LS 1/2
Product Manual
English
Foreword
Thank you for purchasing the Light Storm
The Light storm
carefully to have over 95 CRI value. Delicate design and elaborating production make a robust but
exquisite housing, which can fulll low forward heat of the xture.
You can use V-Mount or Anton Bauer battery in a location shooting. Besides, adapter attached is for
your indoor shooting.
surrounding within 360°. You can also control the brightness of
under the standard DMX512 protocol. Light storm, the best choice for your shooting.
Instructions
Please read this product manual carefully.
Keep this product manual. Always iincludes this product manual when passing the products on to
the third parties.
Heed all warnings and follow all instructions in this product manual as stated.
Please do not disassemble or modify the Light Storm
product malfunction.
Please do not handle with wet hands or immerse in or expose to water or rain, or it could result in
re or electric shock.
Please do not use the Light Storm
explosion.
Please keep all liquids and ammable gas away from the Light Storm.
Keep away from strong sunlight or other high temperature, or it may explode.
Please do not damage, disassemble, drag or wind power cable. Do not place heavy things on the
Light Storm, or it may cause re or electric shock.
Please clean the Light Storm
Use of original Aputure cable accessories is recommended. Please note that this warranty does not
apply to repairs arising out of the malfunction of non-original Aputure accessories, although you
may request such repairs on a chargeable basis.
The product is certicated by ROSH, CE and FCC. Please operate the product in full compliance with
the operation standards. Please note that this warranty does not apply to repairs arising from
malfunction, although you may request such repairs on a chargeable basis.
The instructions and information in this manual are based on thorough, controlled company testing
procedures. Further notice will not be given if the design or specications change.
Intended use
Intended use of the Light Storm
The user has read the instructions of this manual.
The user is using the products within the operating conditions and limitations described in this
product manual.
“Improper use” means using the products other than as described in these instructions or under
operating conditions which dier from those described herein.
LS 1/2
is made of 264 SMD lamp beads which are designed and manufactured
LS 1/2
oers dual power solutions.
LS 1/2
is with the ability to adjust the brightness. Two antennas can cover all the
LS 1/2
in the presence of ammable gas, or it could result in
LS 1/2
with a dry cloth.
LS 1/2
means:
Detailed product manual for Light Storm can be found on the movie solution page on www.aputure.com .
-1-
LS 1/2
by a DMX console which is
LS 1/2
, or it could result in electric shock or
Item check list
Before starting, please check that all the following items have been included
with the Light Storm LS 1/2. If anything is missing, contact your dealer
immediately.
Light Controller box
Controller Button battery
WarrantyProduct manual
*The exceed is for clipping. See the details from "Clipping the tracing paper by the clamps"
Tracing papers (10PCS)
Hook
-2-
Buckle
AC/DC adapter
Power cable
Magic strip
Connect cable
Nomenclature
1. Light
LED beads
Clamp handle Supporting
2. Controller box
3. Controller
Channel indicators
Channel chosing button
Battery compartment
tube
Eyelet bar
Socket
Power switch
Display window
Brightness wheel
DMX input/output
Group A on/o
Group B on/o
Group C on/o
Group D on/o
Cable box
Clip
Antennas
(*The signal strength is the best
when pulling the antennas as
the picture's show.)
Battery Mount
(*Anton Bauer or V-mount)
DC power socket
-3-
HookCooling nsU-frame
Group A brightness button
Group B brightness button
Group C brightness button
Group C color temperature button
Group D brightness button
Group D color temperature button
Tilt knob
4. Display window
Channels indicator
Groups indicator
DMX indicator
Brightness percent indicator
Channel setting button
DMX channel setting button(+)
Group setting button
DMX channel setting button(-)
DMX model setting button
Installations
1. Install the hook
2. Install the light
1) Turn around the clamp handle to install the light on the tripod.
2) Set the light at a specic angle, and pull or turn around the tilt knob to fasten the light.
-4-
3. Insert the connect cable dot to dot to power the light .
*Tie the connect cable around the hook
4. Power the controller box
1) Powered by the adapter
AC 100V-240V
Locking
spring
* Please pull the power adapter out by pushing the locking spring down on the controller box.
-5-
Locking
slot
2) Powered by the battery
V-Mount Battery Anton Bauer Battery
* Battery output current ≥ 4A;
* Please choose the model of the Light Storm by your battery need.
5. Clip the tracing paper by the clamps
Tracing paper
Cable box of the Light
6. Insert the button battery to power the controller.
-6-
Operations
1. Press power switch to turn on the Light Storm.
* “Channel 1 ,Group A” is by default. The brightness is 10% by default.
2. Manual controlled by the controller box
Brightness adjustment and display
3. Remote controlled by the controller
You can control the LS 1/2 of channel 2, group C according to the following directions.
1) The controller box setting
*1) Channel setting and display
-7-
*2) Group setting and display
2) The controller setting and display
Press ( ) to set the channel 2
The controller setting is nished.
*The Light Storm has three channels (1/2/3) and four groups (A、B、C、D).
“ ” indicator lights
3) Brightness adjustment
Press ( or ) of group C to adjust the brightness . The brightness varies in 1% at one press.
Brightness changes between 10 and 100.
-8-
4.The DMX control
1) Connect a standard DMX console
OUTPUT
DMX512
DMX512
Only one Light Storm
OUTPUT
DMX512
DMX512
One by one
* See the interface denition of the DMX as the picture shows:
ground
ground
empty
-9-
groundempty
negative
ground
positive
2) The DMX setting
*1) Press DMX model setting button on the controller box to enter into the DMX model.
*2) Press the DMX channel setting button (+/-) on the controller box to your needed DMX channel.
3) The standard DMX console control
Control the Light Storm by the standard console within the same DMX channel setting as above.
* Channel 1 is by default when in DMX model，DMX channel is between 1 and 512.
Tips and trouble setting
Please turn o the Light Storm
Please do not look at the Light Storm
Please do not keep touching the Light Storm
make you injured.
Please do not drop the Light Storm down; it could result in the reducing of heat dissipation.
Keep a distance of over 10 meters away from the Light Storm
Suggest to take out of the button battery of the controller if do not use the controller for a long
period .
LS 1/2
before removing batteries.
LS 1/2
straightly, or it could damage your eyes.
LS 1/2
-10-
over 5 minutes during lighting, or it could
LS 1/2
.
Specifications
Model
Operation Current
Power Supply
Power Input
Beam Angle
Color Temperature
Average Life Span
Cooling Mode
Radio Frequency
Channels
Groups
Remote Range
Light
Sizes
(L*W*H)
Controller box
(Anton Bauer Battery)
Controller box
(V-Mount)
Brightness (average)
Model
LS 1/2w
LS 1/2w
4A
DC 15V
60W
120°
5500K
≥100,000 hours
Natural convection heat transfer
2.4GHz
1/2/3
A/B/C/D
≤100m
360.5*217.2*25.4 mm
238.0*118.7*48.1 mm
238.0*118.7*59.6 mm
(*vertical antennas included)
(*vertical antennas included)
Distance LUXFootcandles
0.5m
372
1m
4000
1100102
-11-
Loading...