Appleton DBR Receptacles with Disconnect Switch Instruction Sheet

300880-4
INSTRUCTION SHEET
U.S. Patent No. 3,735,078
DBR Receptacles with Disconnect Switch:
30, 60, and 100 Amp.; Dust-lgnition-Proof.
Grounding thru Extra Pole and Shell
Class II, Div. 1 and 2 Groups F*, G Class III NEMA 3, 3R, 4X, 9F*G
DBR Enclosure has O-Ring
Gasket for Dust-Tight,
Rain-Tight Fit.
I. TO DISASSEMBLE RECEPTACLE INTERIOR
1. Remove polarizing screw and washer.
2. Rotate terminal holder counter-clockwise.
II. TO CONNECT CONDUCTORS TO RECEPTACLE INTERIOR
1. Strip insulation from ends of individual conductors.
2. Loosen screws in pressure connectors and slide prepared ends of conductors into the connectors, observing proper polarity. Tighten screws.
III. TO REASSEMBLE RECEPTACLE INTERIOR
1.Insert Terminal Holder and turn clockwise until front end is approximately 1/4” inside of casting surface. Recessed radial depression in Terminal Holder must be lined up with polarizing washer/locator. Replace screw through the ground strip.
IV. POLARITY AND PHASE ROTATION
1. ACP CPH Plugs and EBRH Receptacle are polarized so that the plug will enter the receptacle only one way.
2. Special Polarization: suffix – P4 added to catalog number of the receptacle. Prevents plug insertion in a receptacle wired for a different voltage.
V. Wiring
1. Conductors rom Receptacles are connected to the Disconnect Switch as shown.
TERMINAL
HOLDER
Solderless lugs are provided for line connections and receptacle is prewired to the load side of disconnect switch. Cover-mounted components leave entire enclosure space free for pulling of line conductors and wiring.
POLARIZED SCREW AND WASHER
PRESSURE
CONNECTORS
SCREW
DBR
1-1/2” threaded conduit
openings- one in top
and two in bottom
Plug is mechanically locked in receptacle when switch is ON. Design provides interlocked connect and disconnect operation.
Switch operating handle can be padlocked in either “ON” or “OFF” position.
Dimensions of DBR Receptacles
CONDUIT OPENINGS
TAPPED 1-1/2”
C/L OF CONDUIT OPENINGS
2.75”
7.0 CM
30 Amp 60 Amp 100 Amp 30 Amp 60 Amp 100 Amp
A 14.81" 14.81" 15.25" B 15.5" 17.06" 17.75"
(37.6cm) (37.6cm) (38.72cm) (39.4cm) (43.3cm) (45.1cm)
MOUNTING HOLES
FOR 3/8” DIA. BOLTS
1 1/2 - 11 1/2 NPT
TOP VIEW CONDUIT OPENING
BOTTOM VIEW
CONDUIT OPENING
1.75”
45 CM
3/4 - 14
NPT
3/4 - 14
NPT
TWO
THREADED
1 1/2 CONDUIT
OPENINGS IN BOTTOM
3.00”
7.6 CM
A
C/L OF
CONDUIT OPENINGS
7.44”
18.9 CM
9.06”
23 CM
3.0”
76 CM
14.06”
35.7 CM
B
16.69”
42.4 CM
15.13”
38.4 CM
2.63”
6.7 CM
3.81”
9.7 CM
2.00”
5.1 CM
4.50”
11.4 CM
9.00”
22.9 CM
2.63”
8.7 CM
2.00”
5.1 CM
3.81”
9.7 CM
Dimensions Of Plugs in Inches
ACP Plugs for DBR Receptacles
No. Poles A B C D
30 Amp 2, 3, 4 6.00 4.75 3.13 1.86 60 Amp 2, 3 7 81 4.94 3.50 2.23 60 Amp 4 7.81 4.94 3.81 2.55 100 Amp 2, 3 10.50 6.63 4.00 2.47 100 Amp 4 10.50 6.63 4.25 2.72
CPH Plugs for DBR Receptacles
Max.
Amps. Wire/Pole A B C D E
30 2W, 3P; 3W, 4P 6.13 2.38 1.86 1.81 4.44 60 2W, 3P 8.44 3.06 2.23 3.31 5.69 60 3W, 4P 8.44 3.06 2.55 3.31 5.69
C
D
A
B
D C
B
E
A
CPH 30 Amp. Plug
CPH 60 Amp. Plug
CAUTION: To prevent Ignition of hazardous atmospheres do not use in Class II Group F locations that contain elec­trically conductive dusts. Most coal dusts are not elec­trically conductive.
Page 4 Rev. D 10/30/2000 300880-4
Rev. D 10/30/2000 300880-4 Page 1
Rev. D 10/30/2000 300880-4 Page 3
Page 2 Rev. D 10/30/2000 300880-4
ACP Plugs for EBR, EBRH and DBR Receptacles
Cable Dia., 30 Amp 60 Amp 100 Amp Inches 2W, 3P 3W, 4P 2W, 3P 3W, 4P 2W, 3P 3W, 4P
.390 to 1.375 ACP3023BC ACP3034BC ACP6023BC ACP6034BC --------- --------­.875 to 1.906 --------- --------- --------- --------- ACP1023CD ACP1034CD
CPH Plugs for EBR, EBRH and DBR Receptacles
Cable Dia., 30 Amp 60 Amp Inches 2W, 3P 3W, 4P 2W, 3P 3W, 4P
.500 to .875 CPH3023B CPH3034B --------- --------­.390 to 1.375 --------- --------- CPH6023BC CPH6034BC
ACP PLUG
CPH PLUG
2 WIRE - 3 POLE
GREEN WIRE
GROUNDING STRIP
HALF MOON
CONFIGURATION
GREEN WIRE
GROUNDING STRIP
3 WIRE - 4 POLE
GREEN WIRE
GROUNDING STRIP
HALF MOON
CONFIGURATION
GREEN WIRE
GROUNDING STRIP
1
1
2
2
3
CONTACT
SET SCREW
CONTACT
BLOCK
GROUNDING
STRAP
CONDUCTOR INSULATION
BELOW THIS SURFACE
DBR Receptacles with Disconnect Switch:
30, 60, and 100 Amp.; Dust-lgnition-Proof.
Grounding thru Extra Pole and Shell
Class II, Div. 1 and 2, Groups F*, G Class II NEMA 3, 3R, 4X, 9F*G
Field Wiring Instructions To Connect Field Wiring conductors
1. Remove pressure wire connector buss bar of switch by loosening and removing retaining screw.
2. Attach pressure wire connector to end of line conductor. Wire must be flash with end of connector.
3. Reposition terminal under buss bar.
4. Reinsert and tighten retaining screw.
Disconnect switch is mounted within hinged removable cover.
MOUNTING
PLATE
SPACERS
DISCONNECT
SWITCH
TWO MOUNTING
SCREWS
FRONT VIEW
Disconnect switch is to be mounted (with the front of the disconnect switch facing the inside of the cover) by means of two screws through the back of the disconnect switch, through the spacers and into the mounting plate which are then fastened onto the inside of the cover.
* Do not use where electronically conductive dusts are present (most coal dusts are not electrically conductive). Per NEC 502-1, there are only Div. 1 locations where electronical­ly conductive dusts are present.
DBR Plugs Receptacles
Appleton ACP Plugs are mechanically and elec­tronically interchangeable with Crouse-Hinds APJ plugs as listed at right.
ACP Plug Equivalents
Cable Diameter, Wire/ Catalog Number Inches Pole Crouse-Hinds Appleton
30 Amp Plugs
.390 to 1.375 2W, 3P APJ3385 ACP3023BC .390 to 1.375 3W, 4P APJ3485 ACP3034BC
60 Amp Plug.
390 to 1.375 2W, 3P APJ6385 ACP6023BC .390 to 1.375 3W, 4P APJ6485 ACP6034BC
100 Amp Plug
.875 to 1.906 2W, 3P APJ10387 ACP1023CD .875 to 1.906 3W, 4P APJ10487 ACP1034CD
V. WIRING
1. Conductors from Receptacles are connected to the Disconnect Switch as shown.
Note:
Receptacles with the P4 suffix have the interior rotated 22 1/2˚ for special polarization applications. They are compatible only with the Appleton plugs with the P4 option, or Crouse-Hinds plugs with the S4 option.
DBR Enclosure has O-Ring Gasket for Dust-Tight, Rain-Tight Fit.
Disconnect Switch Mounting
Loading...