APG PG-5000 datasheet

Page 1
Rev. 10.08
Automation Products Group, Inc.
®
PG-5000 Digital Pressure Gauge
Accessories
■
Panel mount flange (rear pressure port only)
■
AC to DC external power supply
■
Shock dampening rubber boot
■
Operational Description
Battery powered digital gauge offers full four digit display.
e PG-5000 four-digit display unit incorporates an all-stainless steel sensor. e sensor is resistant to most typical exposures of vibration and shock. e APG gauge is also less sensitive to the effects of pulsating pressures, a major advantage when compared to vibration sensitive dial gauges. Available options include peak hold, 4-20 mA two wire, 0-2 VDC, and 0-5 VDC outputs.
PG-5000
Digital Pressure Gauge
■
Large, full 4 digit display with 0.5 in. characters
■
Available ranges from vacuum up to 500 psi, and from 0 up to 10,000 psi
■
Microprocessor-based circuit has “TARE” capability standard
■
Display capability to 9999
■
Self-powered by standard 9 V battery
■
±0.25% accuracy of full scale (on selected ranges)
■
Gauge reference pressure
■
Internally compliant to CE
■
On/off button
Options
■
Other units of measure available
■
Other process connection fittings available
■
16-minute auto-off optional at no extra cost
■
Rear pressure port
■
Peak-hold
■
Zero adjust knob
■
0-2 VDC output (battery powered)
■
4-20 mA output (loop powered)
■
0-5 VDC output (external power)
■
Up to ±0.1% full scale accuracy with NIST certification, on selected ranges
■
Cleaned for oxygen service
■
For OEM applications or other configurations, consult factory
■
Applications
No special tools or adaptors are required for installation of the PG-5000. is makes the unit an easy, cost effective replace ment for less accurate, standard mechanical gauges. e unit’s long life, ease of operation, high accuracy, and low cost make it perfect for all applications where standard 2.5 in. or larger mechanical gauges have been used.
Automation Products Group, Inc.
1025 West 1700 North Tel. 1/888/525-7300 Logan, UT 84321 USA Fax 1/435/753-7490
1
w w w . a p g s e n s o r s . c o m
s a l e s @ a p g s e n s o r s . c o m
Page 2
Automation Products Group, Inc.
4-20mA Output vs. Pressure Type Table
Vacuum
20mA
30.0
N/A
N/A
4mA
0.0
Vacuum
Pressure
Pressure Type
F.S.0
Gauge / Absolute
N/A
N/A
20mA
F.S.
4mA
0.0
Compound Gauge
4mA
-30.0
20mA
F.S.
-
0.0
Output
Display*
*Display in inHg, for example only. Note: For a pressure type of compound gauge, with 4-20 mA output, the full scale pressure range minimum is 100 psi.
®
PG-5000 Digital Pressure Gauge
■
Specications
Performance
Standard Pressure Ranges Compound Gauge: From vac up to 500 psi Gauge: From 0 to 10000 psi
Absolute @ ±0.25% Linear Accuracy: From 0 to 5000 psi Absolute @ ±0.1% Linear Accuracy: From 0 to 10000 psi
Overpressure: 2x full scale Burst Pressure: 10x full scale or 20,000 psi (whichever is less) Accuracy (linearity & hysteresis): ±0.25% of full scale (B.F.S.L.) or 2 digital counts, whichever
is greater; NIST traceable certification also available for ±0.25% and ±0.1% accuracy in selected ranges
Stability – One Year Zero Drift: 15-5: < ±0.5% F.S., 316: < ±1% F.S. Thermal Zero Shift > 100 psi: ±0.02% F.S./°F ≤ 100 psi: ±0.04% F.S./°F Thermal Sensitivity Shift > 100 psi: ±0.02% F.S./°F ≤ 100 psi: ±0.04% F.S./°F Life: 10 million cycles minimum
Environmental
Compensated Temp: 20 to 130°F (-7 to 54°C) Storage Temp: -40 to 160°F (-40 to 71°C) Operating Temp: 0 to 160°F (-18 to 71°C)
Electrical
Batteries: Standard 9 V (1), user replaceable (2-year life typical with auto off option) External Power: 10-32 VDC Display Type: 4 digit LCD, 0.5 in. digits Display Resolution: 1 part in 9999 Low Battery Detection: Displays “LBAT” @ 4.0 VDC ±5% with V Adjustments: Front accessible: “Z” Zero Adjust; “S” Span Adjust Auto-Off: 16 minutes (not available with options L1, L3 or L4)
Physical
Weight: 0.36 lb. Construction Materials Case: Injection molded case material EMI-X Wetted Materials: 15-5 SS; 316L SS available at no extra charge (High resolution ranges under
100 psi, in 316L SS incorporate a Hastelloy® C276 diaphragm); One piece Hastelloy® fitting also available (minimum quantities required) 6 Pin Connector: Electrical receptacle, R04-R6M or equivalent with optional output selections (included with optional output selections)
6 Pin Mating Connector: R04-J6F or equivalent (Sold separately. See accessories.) External Power Connector: 1/8 in. – 3 conductor (included with optional external power selection) External Power Mating Connector: 1/8 in. – 3 conductor (included with optional external power
selection) Process Cavity Volume: 0.07
Specifications are subject to change without notice.
Automation Products Group, Inc.
1025 West 1700 North Tel. 1/888/525-7300 Logan, UT 84321 USA Fax 1/435/753-7490
■
Electrical Specications
4-20 mA Output Input Voltage (Excitation): 7 VDC min (no load)
to 35 VDC max
Input Current: 3-30 mA max Output: 4-20 mA ±0.16 mA at set points Output/Input: 2 wire loop powered Resolution: Infinite Protection: Reversed polarity
0-2 VDC Output Input Voltage (Excitation): Battery powered Output: Zero set point is ±0.15 V with a 2 VDC
span ±0.02 VDC
Output/Input: 2 wire Resolution: Infinite
0-5 VDC Output Input Voltage (Excitation): 12 to 31 VDC Input Current: 6 mA max Output: 0-5 VDC / ±0.05 VDC at set points
= 9.0 VDC
IN
Output/Input: Non-isolated 3 wire Resolution: Infinite Protection: Reversed polarity
■
Common Pressure Ranges
®
PDX-W-88341
Range Unit of Display
Option Range Measure Resolution
30* -30 to 0 inHg 0.1
30 0 to 30 psi 0.1
60 0 to 60 psi 0.1
100 0 to 100 psi 0.1
160 0 to 160 psi 0.1
200 0 to 200 psi 0.1
250 0 to 250 psi 0.1
3
in.
500 0 to 500 psi 0.1
1000 0 to 1000 psi 1
2000 0 to 2000 psi 1
5000 0 to 5000 psi 1
10000 0 to 10000 psi 1
Other ranges available.
*Requires VAC option when ordering.
2
w w w . a p g s e n s o r s . c o m
s a l e s @ a p g s e n s o r s . c o m
Page 3
Automation Products Group, Inc.
Z
Automation Products Group
Logan, Utah 84321
PSI
S
Z
Automation Products Group
Logan, Utah 84321
PSI
S
Mfg.
Date:
Accuracy:
ring:
OPTIONAL REAR PORT
3/4 HEX
1/4 NPT
1.20
30.5
1.55
39.4
2.66
67.6
OPTIONAL ZERO ADJ. KNOB
A B C D
E F
Tip
Ctr
Body
PG-5000 Pin Out Table
4-20 mA
+ Excitation – Excitation
N/C N/C N/C N/C N/A N/A N/A
0-2 VDC
N/A N/A N/A N/A N/A
N/A + Output – Output
N/C
Ex Pwr
N/A N/A N/A N/A N/A
N/A + Pwr – Pwr
N/C
6 Pin Circular
1/8" Plug
0-5 VDC
+ Excitation
+ Output – Output
– Excitation
N/C N/C N/A N/A N/A
N/C indicates no connection. N/A indicates not applicable.
A
F
B
E
C
D
6 Pin Connector
Body Center Tip
(Note: Not to scale)
External Power Plug
A
B
C
D
– EXCITATION
+ EXCITATION
Gauge Connector
Typical 4-20 mA Circuit
4-20 mA
CURRENT
LOOP
E
F
– EXCITATION
+ EXCITATION
Gauge Connector
Typical 0-5 VDC Circuit
+
SUPPLY VOLTAGE
+ OUTPUT
– OUTPUT
Controller
Process
L
R
+Vin
A
B
C
D
E
F
Z
Automation Products Group
Logan, Utah 84321
PSI
S
REMOTE TRANSDUCER
®
PG-5000 Digital Pressure Gauge
■
Dimensions — in./mm
■
Wiring
Electrical Cable Specifications
AWG: 26
Stranding: 7/34
Type: MIL-W-16878E
Shield: 36 AWG TPC Braid
Jacket: PVC
■
Linear Accuracy Chart
Display Standard Accuracy
Full Scale Display Resolution Linear Accuracy Options
15.00 but < 20.00* 0.01 0.25% N0, N1
20.00 but < 80.00* 0.01 0.25% N0, N1, N2
30.0 but < 80.0 0.1 Better than 1% N3, N4
80.0 but < 200.0 0.1 0.25% N0, N1
200.0 but < 800.0 0.1 0.25% N0, N1, N2
800 but < 2,000 1 0.25% N0, N1
2,000 but <10,000 1 0.25% N0, N1, N2
*Requires high resolution option Notes:
1. This table refers to linear accuracy for standard fittings. Contact APG for linear accuracies for non-standard fittings.
2. This table lists linear accuracies for specific ranges. For an explanation of how linear accuracy is calculated, please contact APG.
Automation Products Group, Inc.
1025 West 1700 North Tel. 1/888/525-7300 Logan, UT 84321 USA Fax 1/435/753-7490
3
w w w . a p g s e n s o r s . c o m
s a l e s @ a p g s e n s o r s . c o m
Page 4
Automation Products Group, Inc.
®
PG-5000 Digital Pressure Gauge
■
Option Tables
Unit of Measure Table
There are 9 choices available:
psi
kPa inHg
bar inH2O* kgcm
mbar* mmHg* fsw
*Requires G2 option. Other units of measure available.
2
Pressure Type Table
G Gauge
G2 High resolution gauge
CG Compound gauge
V Vac
A Absolute
S Sealed
Port Table
F0 Bottom
F1 Rear
F2 Bottom with 0
F3 Rear with 0
F5 Remote transducer with mV sensor
F6 Rear port with panel bracket installed
F7 Bottom port with rubber boot installed
clean
2
clean
2
Operation Table
Operation Electrical Connector
L0
9 V battery E0
L1 4-20 mA output E1
L2 0-2 VDC output E2
L3 0-5 VDC output E1
L4 External power E2
Option A4 is not available with option L1, L3 or L4.
Electrical Cable Length Table
Cable Length
W0
0 ft.
W1 2 ft. (0.6 m)
W2 5 ft. (1.5 m)
W3 10 ft. (3 m)
W4 25 ft. (7.6 m)
W5 50 ft. (15.2 m)
Process Connection Table
P0 1/4-18 NPTM
P2 1 1/2 in. sanitary
P5 1/4-18 NPTF
P7 7/16-20 SAE male
P14 1/8-27 NPTM
P16 PT 1/4 (BSPM 1/4)
P22 G3/8 (3/8 BSPP) male
Other options available.
▲
This option is standard.
■
Ordering Information
PG-5000 – Range
Unit of Measure
___ See Unit of Measure Table
Pressure Type
G-S See Pressure Type Table
Auto Off
A0
No auto off
A3 8 minute auto off
A4 16 minute auto off
A5 32 minute auto off
Zero Adjustment
Z0
Cover screw
Z1 Z knob
Port
F0-F7 See Port Table
Peak Hold
H0
No peak hold
H1 Peak hold
Operation
L0-L4 See Operation Table
Electrical Connection
E0
No connector
E1 6 pin circular (Mating connector sold separately. See accessories.)
E2 1/8 in., 3-conductor external power and mate
Electrical Cable Length
W0 0 ft. (Use with E1, E2 (no cable) connections)
Mating connectors (E1) with cable. See accessories.
W1-W5 Use with E2 connection. See Electrical Cable Length Table
Process Connection
P0-P22 See Process Connection Table
Accuracy (see Linear Accuracy Chart for details)
N0
±0.25%
N1 ±0.25% with NIST certification (selected ranges)
N2 ±0.1% with NIST certification (select ranges)
N3 ±1% or better
N4 ±1% or better with NIST certification
Materials
M0
15-5 SS
M1 316L SS (under 100 psi, 316L SS/Hastelloy
Consult factory for other material options.
®
)
Accessories
Please order separately, by part number. When ordering a flange or boot as an accessory, they
will not be installed on the gauge.
Description Part Number
6-pin circular mating connector (E1) 509110
6-pin circular mating connector (E1)
with cable (see note below) 509110-X0XX*
*To order a 6-pin circular mating connector with cable, you will need to specify the operation and cable length. Specify operation: L1=1, L3=2; Specify cable: 2, 10, 25 or 50 ft. Example: 509110-1025 is a 4/20 mA output with 25 ft. cable
Description Part Number
Panel mount flange (rear port only) 512598
AC to DC external power supply
(includes E2 mating connector) 511641
Rubber boot 512625
Automation Products Group, Inc.
1025 West 1700 North Tel. 1/888/525-7300 Logan, UT 84321 USA Fax 1/435/753-7490
4
w w w . a p g s e n s o r s . c o m
s a l e s @ a p g s e n s o r s . c o m
Loading...