Battery
Installation
MGE™ Galaxy™ 300
10-40 kVA
380/400/415 V
10-40 kVA
Contents
Overview .......................................................................... 1
IMPORTANT SAFETY INSTRUCTIONS
- SAVE THESE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Product Overview............................................................ 2
Cables and Batteries....................................................... 3
Prepare for Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Battery enclosure with pre-installed batteries . . . . . . . . . . . . . . . . . 4
Battery enclosure without pre-installed batteries . . . . . . . . . . . . . . 5
Connect Communication Cables between the UPS and
Battery Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
External battery temperature (ATIZ) and external battery breaker
signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Connect the Battery Cables between the UPS and
Battery Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
BAT+, BAT-, and N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Connect an XR Battery Enclosure to a running UPS. . . . . . . . . . . . 10
Replace the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Specifications................................................................ 13
Battery Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Recommended Cable Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Recommended Bolt and Lug Size . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Torque specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
MGE™ Galaxy™ 300 10-40 kVA 3:3 - 380/400/415 V, 10-30 kVA 3:1 - 380/400/415 V Installation
i
Checklist......................................................................... 15
Appendix ........................................................................ 16
One-line diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Battery cabling YUASA 15 kVA 60 min. . . . . . . . . . . . . . . . . . . . . . . 17
Battery cabling YUASA 20/30 kVA 60 min. . . . . . . . . . . . . . . . . . . . 18
Battery cabling YUASA 40 kVA 60 min. . . . . . . . . . . . . . . . . . . . . . . 19
Battery cabling CSB 15 kVA 60 min. . . . . . . . . . . . . . . . . . . . . . . . . 20
Battery cabling CSB 30 kVA 60 min. . . . . . . . . . . . . . . . . . . . . . . . . 21
Battery cabling CSB 40 kVA 60 min. . . . . . . . . . . . . . . . . . . . . . . . . 22
ii
MGE™ Galaxy™ 300 10-40 kVA 3:3 - 380/400/415 V, 10-30 kVA 3:1 - 380/400/415 V Installation
Overview
IMPORTANT SAFETY INSTRUCTIONS
- SAVE THESE INSTRUCTIONS
Warning: ALL safety instructions in the Safety Sheet (990-3620) must be read,
understood and followed when installing the UPS and XR Battery enclsoure(s). Failure
to do so could result in equipment damage, serious injury, or death.
Warning: The maximum storage time of the UPS is limited to six months due to the need
of recharging the integrated batteries. If the UPS remains de-energised for a long period,
we recommend that you energise the UPS for a period of 24 hours, at least once every
month. This charges the battery, thus avoiding possible irreversible damage.
Caution: All electrical power and power control wiring must be installed by a qualified
electrician, and must comply with local and national regulations for maximum power rating.
1MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation
Product Overview
Front view
Battery shelves
Battery circuit breaker
Ground cable connection
(from the UPS)
Battery temperature sensor
(ATIZ)
Connection terminal
MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation2
Cables and Batteries
Front view
Front view
Note: The battery enclosure must be installed on a non-inflammable, level and solid floor.
Prepare for Cables
1. Open the front door.
2. Remove both side panels.
3MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation
Battery enclosure with pre-installed batteries
Front view
Warning: Remove all cardboard used to protect the batteries during transport. Make
sure that cables and copper bars are separated.
Note: A maximum of two battery enclosures can be connected to the UPS (one XR Battery
enclosure with a circuit breaker plus one enclosure without a circuit breaker) by a batch cable
between the UPS and the circuit breaker in the battery enclosure.
1. Remove the left and right plastic cover from the battery breaker by removing the two screws
fastening each plastic cover.
MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation4
2. Connect the batteries to
Front view
+
N
-
the battery breaker by
running the cables from
the battery breaker to
each shelve. Note! Make
sure to run the cables in
this order.
Battery enclosure without pre-installed batteries
Warning: APC by Schneider is not responsible for the wiring of external non-APC
batteries.
Warning: Remove all cardboard used to protect the batteries during transport. Make
sure that cables and copper bars are separated.
Note: Before the installation of batteries, you must select and follow the diagram under
“Appendix” on page 16 which applies to your configuration.
Note: The maximum weight of each battery shelf is 155 kg.
Note: A maximum of four battery shelves can be installed.
5MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation
Note: A maximum of two battery enclosures can be connected to the UPS (one XR Battery
Front view
+
N
-
enclosure with a circuit breaker plus one enclosure without a circuit breaker) by a batch cable
between the UPS and the circuit breaker in the battery enclosure.
1. Insert the batteries on the shelves starting from the bottom according to the relevant diagram for
your configuration under “Appendix” on page 16.
2. Connect the batteries
according to the chosen
configuration diagram.
3. Install a battery breaker.
4. Connect the batteries to
the battery breaker by
running the cables from
the battery breaker to
each shelve. Note! Make
sure to run the cables in
this order.
MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation6
Connect Communication Cables between the UPS
Front view
Battery breaker signal
cable to the UPS
To the UPS
Battery
enclosure
and Battery Enclosure
External battery temperature (ATIZ) and external battery breaker signal
Note: The ATIZ cable is for external battery temperature detection signal (cable is pre-
installed).
Note: The battery cable is for external battery breaker signal (cable is pre-installed).
Note: The connection of communication cables is only applicable between the UPS and XR1.
For the connection of XR2, follow step 2 only.
1. Run the combined
battery breaker and
ATIZ signal cable from
the XR connection
terminal as shown.
Note! See the UPS
installation manual for
information on where
to connect the other
end of the cable(s) to
the UPS.
2. Run the four cables
from the XR
connection terminal to
the XR battery breaker
(see the below table for
cable description).
Cable description (step 2)
Cable color Cable label Description
Yellow QB OF-11 CB contactor signal
White QB OF-14 CB contactor signal
Red QB OF-D4 +12 V power supply
Black QB OF-D1 -12 V power supply
7MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation
Connect the Battery Cables between the UPS and
+
N
-
+
N
-
Front view
Cables to/from the UPS
Battery
enclosure
Battery Enclosure
Warning: This procedure describes how to connect the initial battery cables between
the UPS and XR before start-up. If the UPS is up running, see “Connect an XR Battery
Enclosure to a running UPS” on page 10.
BAT+, BAT-, and N
1. Run the ground cable up
through the bottom front hole of
the XR and connect it to the
busbar.
2. Run the BAT+, N, and BATcables up through the bottom
front hole.
3. Attach the cables to the right
side of the battery breaker.
4. Reinstall the side panels.
MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation8
Ba
t
t
e
r
y
1
0
-
4
0
k
V
A
3
:
3
B
a
t
t
e
r
y
Rear view of the
UPS
B
a
t
t
e
r
y
2
0
-
3
0
k
V
A
3
:
1
1
0
-
1
5
k
V
A
3
:
1
+
,
N
,
-
+
,
N
,
-
+
,
N
,
-
5. Connect the battery cables to the battery terminals in the UPS. See the UPS installation manual
for information on how to remove the I/O sheet metal cover.
6. Re-install the UPS covers. See the UPS installation manual for more information.
9MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation
Connect an XR Battery Enclosure to a running UPS
Warning: Before connecting an XR battery enclosure, ALL safety instructions in the
Safety Sheet (990-3620) must be read, understood and followed. Failure to do so could
result in equipment damage, serious injury, or death.
Note: This procedure describes how to connect an XR battery enclosure to a UPS running in
normal operation.
Note: A maximum of two battery enclosures can be connected to the UPS (one XR Battery
enclosure with a circuit breaker plus one enclosure without a circuit breaker) by a batch cable
between the UPS and the circuit breaker in the battery enclosure.
Note: Before carrying out the below procedure, make sure that the UPS is running in normal
operation with no internal UPS faults displayed. In normal operation all breakers must be in
the ON (closed) position except for the maintenance bypass breaker which must be in the
OFF (opened) position.
1. Turn the UPS into maintenance bypass operation:
a. Turn the static bypass breaker (QM2) to the ON (closed) position.
b. Turn the maintenance bypass breaker (Q3BP) to the ON (closed) position.
c. Turn the static bypass breaker (QM2) to the OFF (opened) position.
d. Turn the output breaker (QOP) to the OFF (opened) position.
2. Isolate the batteries by turning the UPS battery breaker (QB) (and the existing XR battery
breaker (QFB), if present) to the OFF (opened) position.
3. Remove all internal batteries in the UPS enclosure.
4. Prepare for cables. See “Prepare for Cables” on page 3.
5. Install the batteries. See “Battery enclosure with pre-installed batteries” on page 4 or “Battery
enclosure without pre-installed batteries” on page 5.
6. Connect the communication cables between the UPS and the XR. See “Connect Communication
Cables between the UPS and Battery Enclosure” on page 7.
7. Connect the XR Battery enclosure according to the relevant, electrical diagram under
“Appendix” on page 16, and according to the chapter “Connect the Battery Cables between the
UPS and Battery Enclosure” on page 8.
8. Verify the battery wiring as described under “Battery enclosure with pre-installed batteries” on
page 4 or “Battery enclosure without pre-installed batteries” on page 5
MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation10
Electrical Hazard: Check the DC voltages with a DC voltage multimeter versus the battery
voltage before continuing.
7. Turn the XR battery breaker (QFB) to the ON (closed) position.
8. Turn the UPS back into normal operation:
a. Turn the static bypass breaker (QM2) to the ON (closed) position.
b. Turn the output breaker (QOP) to the ON (closed) position.
c. Turn the maintenance bypass breaker (Q3BP) to the OFF (opened) position.
d. Turn the UPS battery breaker (QB) to the ON (closed) position.
e. Turn the input breaker (QM1) to the ON (closed) position.
9. Check the LEDs to see if the UPS is running in normal operation:
• PFC LED: green
• INVERTER LED: green
• LOAD LED: green
• LOAD PROTECTED LED: green
• Other LEDs: OFF
11MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation
Replace the Batteries
Warning: Before battery replacement, ALL safety instructions in the Safety Sheet (990-
3620) must be read, understood and followed. Failure to do so could result in equipment
damage, serious injury, or death.
Caution: Batteries must be replaced by qualified electricians only.
Note: For the replacement of batteries, please refer to the relevant diagram for your
configuration under “Appendix” on page 16.
Note: Before replacing batteries, make sure that the UPS is running in normal operation with
no internal UPS faults displayed. In normal operation all breakers must be in the ON (closed)
position except for the maintenance bypass breaker which must be in the OFF (opened)
position.
Note: Replacing batteries in the UPS and in the XR enclosure(s) requires that the UPS is
turned into maintenance bypass operation and that the batteries are disconnected. Follow the
procedure described under “Connect an XR Battery Enclosure to a running UPS” on page 10.
MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation12
Specifications
Battery Output
Battery Description
Nom voltage (V) 12 v/block
I
discharge
Nom
I
discharge
Max
End Voltage 9.9 v/block
1
Nominal battery discharge current based on rated load and nominal battery voltage.
2
Maximum battery discharge current based on rated load at the end of the discharge.
Recommended Cable Sizes
1
2
See the battery input table in the UPS installation manual 990-3618
See the battery input table in the UPS installation guide 990-3618
Caution: All wiring must comply with all applicable national and/or electrical codes.
Note:
AC cable sizes are determined for:
- the TNS system for copper, single-core cables, type U1000 R02V, 100 m long with a line
voltage drop <3%, installed on perforated cable trays, XLPE-type insulation, single-layer
trefoil formation, THDI between 15% and 33%, 35°C, at 400 V, grouped in four touching
cables.
Battery cable sizes are determined for:
- copper, single-core cables, type U1000 R02V, maximum length 25 m with a line voltage
drop <1%.
3:3 3:1
kVA
Mains input (mm²) 10 35 10 35 10 35 16 35 25 35 10 35 10 35 10 90 16 90
AC output (mm²) 10 35 1035 1035 16352535103525353590 7090
Battery (mm²) 10 35 10 35 16 35 25 35 35 35 10 35 10 35 16 25 25 35
Bypass (mm²) 10 35 103510351635 3535103525343590 7090
10 15 20 30 40 10 15 20 30
min max min max min max min max min max min max min max min max min max
13MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation
Recommended Bolt and Lug Size
Torque specifications
Battery Terminal Bolt size Torque
CSB
910-0631 clip
910-0633 M6 5.4 NM (max 8.2 NM)
YUASA
912-0001 M5 2.5 NM (max 6 NM)
910-0632 M6 4.8 NM (max 6 NM)
MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation14
Checklist
Make sure that all cardboard and strappings have been removed.
Check that the power wiring is torqued as described in the torque specification table above.
Verify clockwise phase-rotation (BAT+, N and BAT-) and make sure that a neutral connection
is present.
Leave a wiring diagram on site for service personnel.
Re-install all wiring access panels on the UPS.
For any optional equipment, refer to product-specific manuals.
Make sure that all battery breakers (on the UPS unit and XR Battery Enclosure(s) if
applicable) are in the
OFF (opened) position.
15MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation
Appendix
One-line diagrams
Note: Use the below table as a help to find the diagram that fits your system.
YUASA CSB
Part no.
Name
Battery
enclosure qty.
15 KVA
60 min
885-4766B 885-4767B 885-4770B 885-4769A 885-4773A 885-4774A
G3HTBAT1 G3HTBAT2 G3HTBAT3 G3HTBAT1 G3HTBAT2 G3HTBAT3
12 2 12 2
20 KVA/
30 KVA
60 min
Note:
- marked cables are assembled by the manufacturer.
- marked cables are assembled on site by APC by Schneider or a sub contractor.
Black diagram lines represent white cables.
40 KVA
60 min
15 KVA
60 min
30 KVA
60 min
40 KVA
60 min
MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation16
Battery cabling YUASA 15 kVA 60 min.
*Torque for screws to link
batteries is 2.5 Nm
No. Item Description Part no. Qty.
A Battery Yuasa battery SWL 1100 912-0001 30
B Copper bar 70*25*2 880-2755 20
C Power cable Wire 16 mm
D Power cable Wire 16 mm
E Power cable Wire Assy 16 mm
F Power cable Wire Assy 16 mm
G Power cable Wire Assy 1 string CBN 0W4989 1
H Power cable Wire Assy 16 mm
2
Ivory 380 mm 0W5032 3
2
Ivory 640mm 0W5035 3
2
Ivory 1200 mm 0W5034 2
2
red 900 mm CB+ 0W4982 1
2
White 900 mm CB- 0W4986 1
17MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation
Battery cabling YUASA 20/30 kVA 60 min.
*Torque for screws to link
batteries is 4.8 Nm
No. Item Description Part no. Qty.
A Battery Yuasa battery SWL 1850 910-0632 30
B Copper bar 110*25*3 880-2754 14
C Power cable Wire 16 mm
D Power cable Wire 16 mm
E Power cable Wire Assy 16 mm
F Power cable Wire Assy 16 mm
G Power cable Wire Assy 1 string CBN 0W4991 1
H Power cable Wire Assy 16 mm
2
Ivory 380 mm 0W5032 4
2
Ivory 640mm 0W5035 6
2
Ivory 1200 mm 0W5034 4
2
red 1800 mm CB+ 0W4983 1
2
White 900 mm CB- 0W4986 1
MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation18
Battery cabling YUASA 40 kVA 60 min.
*Torque for screws to link
batteries is 2.5 Nm
No. Item Description Part no. Qty.
A Battery Yuasa battery SWL 1100 912-0001 64
B Copper bar 70*25*2 880-2755 40
C Power cable Wire 16 mm
D Power cable Wire 16 mm
E Power cable Wire Assy 16 mm
F Power cable Wire Assy 2 strings CB+ 0W4984 1
G Power cable Wire Assy 2 strings CBN 0W4992 1
H Power cable Wire Assy 2 strings CB- 0W4987 1
2
Ivory 380 mm 0W5032 4
2
Ivory 640mm 0W5035 12
2
Ivory 1200 mm 0W5034 4
19MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation
Battery cabling CSB 15 kVA 60 min.
No. Item Description Part no. Qty.
A Battery CSB battery GP12120 910-0631 90
B Power cable Wire 10 BLK 120 mm 0W4946 72
C Power cable Wire Awg 10 BLK 520 mm 0W4969 6
D Power cable Wire Awg 10 BLK 640 mm 0W4971 6
E Power cable Wire Assy 3 strings CB+ 0W4973 1
F Power cable Wire Assy 3 strings CBn 0W4981 1
G Power cable Wire Assy 3 strings CB- 0W4976 1
MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation20
Battery cabling CSB 30 kVA 60 min.
*Torque for screws to link
batteries is 5.4 Nm
No. Item Description Part no. Qty.
A Battery CSB battery GP12340 910-0633 64
B Copper bar Copper bar CU-ETP Battery GP12340 880-6019 36
C Power cable Wire 16mm
D Power cable Wire 16mm
E Power cable Wire 16mm
F Power cable Wire Assy 2 strings CB+ 0W4984 1
G Power cable Wire Assy 2 strings CBn 0W4992 1
H Power cable Wire Assy 2 strings CB- 0W4987 1
2
Ivory 520 mm 0W5033 12
2
Ivory 640 mm 0W5035 8
2
Ivory 1200 mm 0W5034 4
21MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation
Battery cabling CSB 40 kVA 60 min.
*Torque for screws to link
batteries is 5.4 Nm
No. Item Description Part no. Qty.
A Battery CSB battery GP12340 910-0633 90
B Copper bar Copper bar CU-ETP Battery GP12340 880-6019 60
C Power cable Wire 16 mm
D Power cable Wire 16 mm
E Power cable Wire Assy 3 strings CB+ 0W4985 1
F Power cable Wire Assy 3 strings CBn 0W4993 1
G Power cable Wire Assy 3 strings CB- 0W4988 1
2
Ivory 520mm 0W5033 12
2
Ivory 640 mm 0W5035 12
MGE™ Galaxy™ 300 10-40 kVA 3:3, 10-30 kVA 3:1 - 380/400/415 V Installation22
APC Worldwide Customer Support
Customer support for this or any other APC product is available at no charge in any of the following ways:
• Visit the APC Web site to access documents in the APC Knowledge Base and to submit customer
support requests.
– www.apc.com (Corporate Headquarters)
Connect to localized APC Web sites for specific countries, each of which provides customer support
information.
– www.apc.com/support/
Global support searching APC Knowledge Base and using e-support.
• Contact the
– Local, country-specific centers: go to www.apc.com/support/contact for contact information.
For information on how to obtain local customer support, contact the APC representative or other distributors
from whom you purchased your APC product.
APC Customer Support Center by telephone or e-mail.
Entire contents copyright 2010 American Power Conversion Corporation. All rights reserved. Reproduction
in whole or in part without permission is prohibited. APC, the APC logo, and TRADEMARK NAMES are
trademarks of American Power Conversion Corporation. All other trademarks, product names, and corporate
names are the property of their respective owners and are used for informational purposes only.
6/2010990-3617-001
*990-3617-001*
Loading...