Thanks for your purchase of our product Tablet PC . Its MCU is MT8735, it is based on
Android 7.0 operation system, and easy to expand the third application procedure.
The product is designed with various functions, including GSM,WCDMA,LTE, WIFI, BT,
GPS,FM, voice call and so on. It is easy to achieve wireless communication and internet, you have
access to surf the internet anytime and anywhere; it is also built with high accuracy GPS module,
so that it can be used for navigating th rough installing map software. There are many sensors
which offer you brand-new operation and entertainment; besides, it has camera shooting, which
leads electronic consumption to enter into a fresh palm internet entertainment time.
The manual systemically introduces the functions, use techniques and announcements, please
read this manual carefully before your operation.
1.2 Announcements
Preventive maintainance
Please always keep the Tablet PC dry. To avoid the device short trouble, corrosion
fault and electric short, please prevent the device, battery and charger from water and
moisture, and don’t operate the device or charger by wet hand.
To avoid failure of device, battery and charger, please prevent the device, battery,
charger from violent shock or shake.
To avoid failure of device, battery and charger, please prevent the device, battery,
charger of all over heating or too cold circumstance
Never shock, throw, prod the Tablet PC, or drop, extrude,bend the .Tablet PC
Never disassemble the device and accessories arbitrarily, otherwise the device and
accessories are not in our company warranty scope.
1.3 Safety Instruction
Before the operation of the Tablet PC please read this chapter and teach your kids about these
information. For further details, please refer to the safety instructions and a nnouncement.
Never use the Tablet PCwhen driving car, in order to ensure safe driving.
3
Page 4
In the medical area, please abide by related rules and regulations. Please shut
down the Tablet PCwhen it is near to the medical area.
To avoid the wireless signal to interrupt the plane- co ntrolled signal, please shut
down the Tablet PCor using airplane mode when you are boarding a flight,
To avoid electronic equipment failure, please shut down the Tablet PC in the
vicinage of high-accuracy electronic equipments.
F
Please don’t disassemble the Tablet PC and accessories. Only authorized agent has
access to service the Tablet PC.
Please keep the Tablet PC far away from magnetic equipments, the radiation of
Tablet PC may erase the data stored in the magnetic equipments.
Never use the Tablet PCin the vicinage of high temperature, inflammable gas
( gas station).
Protect the Tablet PC and accessories from kids re ach scope, and avoid the kids to
use theTablet PCwithout parents’ supervision.
Please comply with related rules and regulations, and respect others’ privacy and
legal rights whil e using theTablet PC
Please strictly adhere to related instructions in the manual when using USB cable
to ensure the safety of the Tablet PC
Never use the Tablet PC in bathroom or oth er husmartphone environment, and
please protect the Tablet PCfrom liquid wash or wet.
4
Page 5
2 Tablet PC Introduction
2.1 Tablet PCOperation and Preparation
Battery Charging
If this navigator is first used, please use AV adaptor to fully charge it.
1. Applythe power adptor to charge for Tablet PC
2.2Tablet PCStatus and Reminder
Reminder icons
When some remind message appears in your reminder window, please click column and slip
the screen to open the reminder list. Choose the menu you need, and confirm the information.
Then you can close the reminder window through clicking the column to slide up. Please refer to
below status icons:
bluetoothairplain mode
The connected USB
USB connected
debugging
Wi-fi is connected, the
flashlight
network is av ailable
battery capacity
Reminder board
Reminder icons will work while receiving emails, WIFI is open, you can open the reminder
board to view the detailed information.
Open the reminder board
When the reminder column shows new reminder icon, please hold the column and slip down
your finger, then the reminder board is opened.
5
Page 6
3 Quick Start Guide
3.1 Keys Function
Keys Funcction Description:
Power buttonShort press to sleep/wake up, long press to startup and
Volume +(up)increase the volume
Volume -(down)decreasethe volume
HOME button (home)Click it in any interface will return to main interface.
shutdown.
Back button(back)
Menu buttonThis button will display in menu interface.
click it in any interface will return to previous menu
3.2 Startup and Shutdown
Startup
Long press POWER key for three seconds, you can enter into startup picture. The system
enters into screen lock status, please unlock it.
Shutdown
1. Long press POWER, it will popoup shutdown window.
2. Shutdowm window contains mute mode, airplane mode,reboot mode and shutdown
four options.
3. Click Shutdown is the last step.
3.3 Open and Close of the Screen
Screen will be closed on its own when no operation happens.
1. Screen will be closed on its own if no operation happens for some time to save battery
power
2. When screen is open, press POWER key, the screen will be closed immediately.
6
Page 7
Open the screen when it is closed.
If the screen is closed, short press POWER to open the screen. The screen will be locked
open it, it will show the picture as below picture, left slide to unlock and enter into camera, right
slide the unlock icon to unlock the screen.
Picture 3.1
3.4 Usage of Touch Screen
Tablet PCoperating methods
There are below methods to view the main screen, menu and application procedure in your Tablet
PC
Click
When you want to use the screen keyboard typing or choose appli cation in the main interface, you
only need to touch it by your finger.
Press on
Ifyouwanttoopensomeitem(textboxorthelinkinthewebpage),orshortcutandmain
procedure move, you can press on this item.
Quickly slide or slide
Quickly slide or slide indicates make quick vertical or horizoncial movement by finger.
For most pictures, you only need to retate the Tablet PC sidewise to change the screen direction
from horizoncial to vertical. For instance, when you are typing wods, and watching movies.
3.5 Home Page
Main interface as below picture 3.2, long press the blank and it will popup windows to set
wallpaper, folder, widgets, and shortcut.
Batty volume
Notice column
search
time
application program
Picture 3.2
The extended home page
The home page can be extended beyond the wideness of screen to provide more space,
which you can put new-added shortcuts and widgets. Click the blank space in home page
then slide right or left to extend to the right or left of the screen. In the home page, there are
two extended pictures, as Picture 3.3.
8
Page 9
Picture 3.3
The shortcut icons management in desktop application.
Create folder icon in desktop
1. Drag the icons need to be p ut together on one icon(can also overlay several
icons)as Picture 3.4.
Click the unnamed folder in the black box, it will popup the hidden keyboard, the folder name
can be renamed (this is similiar with Apple IOS system), the icons position can be changed
through long press.
9
Page 10
Picture 3.4
Remove the icons in desktop
1.Long press the icons need to be remove, then on the right above of the screen, it
will appearicons.
2.Drag th e icon to the above of the remove icon, till the icon become red, then move
your finger to delete the icon.
Change the wallpaper of desktop
1. In home page, long press any blank space in main screen, it will popup a window
to change the wallpaper.
2.
Click the gallery or wallpaper gallery to select t h e wallpaper.
3.6 VisitApplication Procedures
Clickin right top of Picture 3.2, enter into main interface as Picture 3.6,
choose the application procedure you want to visit.
10
Page 11
Picture 3.6
3.7 USB Connection
Tablet PCstorage configuration
Before transmitting documents, you have to conduct storage configuration for your Tablet PC:
1. Connect the Tablet PCand computer by USB cable, the reminder column will show
the remind information.
2.Open the reminder board; please view the Tablet PCstatus and reminder to learn how
to open the board.
3.In the reminder board, click the “USB Connected”, it will as below Picture 3.4, then
click “open USB storage configuration”.
4.Now the USB is connected successfully.
11
Page 12
Picture 3.7
Copy the document into memory card
1.Connect the Tablet PC to computer with USB cable.
2. As Tablet PC storage configuration, it is connected with computer successfully.
3.Open the “My computer” in your computer, check the items in “removable disc”.
4.Copy the documents you need into “removable disc”.
5.After copying finishes, click “shutdown the USB storage configuration” to uninstall.
3.8 Typing words
Use the screen keyboard
When you start the procedure or choose the words or numbers edition, it will show the screen
keyboard. The keyboard contains below typing options:
1. Android keyboard
2. Google Pinyin
Choose the typing method you want
1. Click Setting pocedure application.
2. Click Language and Keyboard.
3. In the text setting area will reveal all the installed words-typing methods in your Tablet
PC
4. Tick the typing method you want.
12
Page 13
Use and switch of input method
⑤
①
②
Picture 3.8
1switch the capital and small letter
2switch the mode of words input
3click to insert the space
4click input to execute
delete the character in the left of cursor, click and hold to delete all the
5
characters in the left og the cursor.
④
③
3.9 Operation Technique
Enter widgets interface
In the application interface,click widgets on the above of screen, or slide the screen, it
will swtich into widgets interface. Long press any widget to create its shortcut, then
13
Page 14
you can enter into the application through the shortcuticon.
Create application shortcut icons in the desktop
In the application interface or widgets interface, long press any icon to switch into
desktop automatically, drag and hold the icon, you can move to any position in the
desktop.
Remind: If the target position has no space, the widget won’t be add in the main
screen.
4 Basic Setting
4.1 SIM Management
4.1-1 Voice call
Click settings in main menu, choose SIM Management, as Picture 4.1
14
Page 15
Picture 4.1
Click voice call, choose defaulted SIM card, as Picture 4.2
4.2 Wireless and Internet
1. Connect Wi-Fi
1) In the main menu or interface, choose setting application procedure.
2) Click WLAN, open wifi, Tablet PC will automatically search the available Wifi
Picture 4.2
15
Page 16
wireless internet.As Picture 4.3
3) Choose the Wi-Fi internet you want to connect, if it has password, it will popup the
password window, enter password, click connect.
Picture 4.3
2. Add Network
1) Clickicon in right top, as Picture 4.4
Picture 4.4
2) Input network SSID, the wireless network name, click save.
3) Click user name already saved, click connect to use network, as Picture 4.5
16
Page 17
3. Network Notice
If you open Network Notice, when WIFI signal appears, the right bottom will
remind you available WLAN network, as Picture 4.3
4. Keep WI-FI on during sleep..
Picture 4.5
1. Click
icon in right top of Picture 4.6, select advanced.
2. Click Keep WI-FI on during sleep, as Picture 4.7
Picture 4.7
17
Page 18
4.3Bluetooth
Bluetooth function operation
1. Click setting application in main menu interface
2. Click bluetooth and open it.
3. If somebody open bluetooth in your surroudings, click search device in right above,
then Tablet PCwill automatically search the bluetooth device nearby. As picture 4.8
Picture 4.8
4. Click the available Bluetooth device, it will popup request window, enter into related
password,and match the device to connect.
5. After match successfully, choose the operation you want to, click
Picture 4.9.
to enter into
18
Page 19
Bluetooth setting
1. Rename tablet
Picture 4.9
Click
icon in right top of Picture 4.6, as Picture 4.10, select rename tablet, you
can rename it as you want
Picture 4.10
2.Display the file you received
Choose display the file you received in Picture 4.10, you can view download
and upload files.
19
Page 20
4.4 Data Usage
Check SIM card data usage, as Picture 4.11
Picture 4.11
Check WIFI data usage
Click
icon in right top of Picture 4.11 click Data Usage, as Picture 4.12
20
Page 21
Picture 4.12
4.5 More
4.5-1Airplane Mode
Airplane Mode can turn offWIFI and GSM card function quickly, when airplane mode is tu rned
on, WIFI and GSM can’t get any signal, then airplane mode is turned off, WIFI and GSM module
will recover to previous state.
4.5-2VPN
Open VPN, click add VPN network,asPicture4.13.Inputname and server address, then save.
21
Page 22
Picture 4.13
Click VPN, as Picture 4.14, input VPN user name and password, click connect.
Picture 4.14
4.5-3 Network sharing and portable hotspots
Portable WI-FI hotspots
1. Click setting application in main menu.
2. Click more when wifi is well connected, open network share and portable hotspot
22
Page 23
Picture 4.15
Picture 4.16
3. Click keep WI-FI hotspots on, choose open time.
4. Return to previous menu, open portable WLAN hotspots, click Set up WI-FI
hotspots.
23
Page 24
Picture 4.17
5. Set passwords you want to, password should be more than 8 numbers.
4.5-4 Mobile Networks
1.Access Point Name(APN)
Choose access points name (APN), choose SIM card you need to connect,
Choose connect type
3. Network Operator
Click network operator, choose SIM card you need to connect, system will search available GSM
and WCDMA network,asPicture4.18
Picture 4.18
24
Page 25
4.5-5 GPRS data prior mode
After Open GPRS da ta prior mode, systems will priority chooses your network.
4.6 Sound & notification
1. Open settings, click contextual model, as Picture 4.19,
Picture 4.19
2. Click standard to enter into Picture 4.20
Picture 4.20
1. Vibrate
In picture 4.20, click vibrate,Tablet PC will vibrate when someone calls you.
2. Volume
In picture 4.27, click volume, you can set r ingtone, notice, and alarm volume, as Picture 4.21
25
Page 26
Picture 4.21
3. Voice call Ringtone
In picture 4.27, click phone ringtone to choose voice call ringtone, as Picture 4.22
Picture 4.22
(Note: Except standard, silent, meet, outdoor are only for selection, they can’t be set.)
4.7 Display
4.7-1 Adjust the screen brightness
1. Click Setting application procedure.
2. Click display, choose brightness,
3. Drag the portlito to adjust the brightness volume.As Picture 4.23
26
Page 27
Picture 4.23
4. Click OK after brightness is adjusted.
4.7-2Wallpapers
1. Click setting application.
2. Click display, click wallpaper.
3. You can choose different wallpapers as you like—live wallpapers---gallery(user
defined)---wallpapers (system defect)---video wallpaper, as Picture 4.24
Picture 4.24
4.7-3 Auto rotation
System is defaulted as open auto rotation, when it is turned off, system won’t rotate
Tablet PCscreen by G-sensor.
4.7-4 Sleep
27
Page 28
4. Click setting appliation.
5. Click display.
6. Click sleep.
7. Set the sleep time as you want, as Picture 4.25
Picture 4.25
4.7-5 Font size
Click font size to adjust the font size, as Picture 4.26
Picture 4.26
28
Page 29
4.8 Storage
Open setting function, click memory, click preferred install location, you can
choose isntall new application to choose preferred install location.
Check SD card and Tablet PCstorage space.
Enter into setting application.
1.
Click storage, check storage space.
2.
1.Internal storage
(1) System storage
System storage is the spcae Tablet PC leave for system file, as
Picture 4.27. it can’t be viewed.
Picture 4.27
(2)Internal storage
Internal storage is Tablet PClocal NAND storage, as Picture 4.39, if you need to check the
storage content, you can check it in main menu.
29
Page 30
Picture 4.28
2. SD card
You can check storage space, SD card available space, unmount SD card and erease
SD card, as Picture 4.29
Safely remove SD card
1.Click setting application.
2.Click memory.
3.Click uninstall SD card.
Picture 4.29
30
Page 31
4.Now you can remove SD card safely.
Note: Removing SD card safely can protect SD card and increase its lifetime.
4.9Battery
Click setting function, select battery, you can view the battery situation, as Picture 4.30
4.10Application program
1.ClicksettingapplicationinApps.
2.Select application, after enter, you can manage and delete installed application and
check system used storage space and left space. (As Picture 4.31)
Picture 4.30
31
Page 32
Picture 4.31
3.View the working device, used space and available space, as Picture 4.32
4.11 Account and Sync
1. Select setting application
Picture 4.32
32
Page 33
2. Open account and sync, as Picture 4.33
Picture 4.33
3. Click add an account, as Picture 4.34
Picture 4.34
33
Page 34
4.12 Location service
Click setting,selectMode, as Picture 4.36
Picture 4.36
4.13 Safety setting
Set locked screen
Lock the touch screen by unlock icon or password to protect your Tablet PC.
Note: After setting screen locked, you should enter the passcode each time when you
startup or s creen is locked
Set unlocked picture
1. Clicksettingapplicationinmaininterface.
2. Click safe.
3. Click locked the screen.
4. Choose picture in text setting area.
5. Click next following the remind message.
6. The unlocked pattern board pop up, there are nine touch spots, connect 4
points from vertical, horizontal or diagonal direction. As Picture 4.10, move
34
Page 35
your finger from the screen when finish. The system will record yous new
unlock pattern.
7. Click continue.
8. When you see the reminder, enter the unlock pattern, then click confirm.
Set unlock PIN code
1. Click setting application in main interface.
2. Click safe.
3. Click screen locked.
4. Choose PIN in text setting area.
5. Enter new PIN code(numbers) and click continue.
6. Ener new PIN code again and click confirm.
Set unlock password
1. Click setting application in main interface.
2. Click safe.
3. Click screen locked.
4. Set password in text seting area.
5. Set new password(letters and numbers) and then click continue.
6. Enter the password again and the click confirm.
Picture 4.37
Unknown source
1.In main interface, click setting.
2.Click safety.
35
Page 36
3.Click unknown source,as Picture 4.54
Picture 4.38
Note:Manual installing APK files needs to turn on unknown source.
4.14 Language and Input Method
Click setting, select language and input method, choose language to switch language, as
Picture 4.39
Click setting, choose language and input, choose Android keyboard setting, click input
language, as Picture 4.56
36
Page 37
Picture 4.40
Choose the language you want to change in the language list, as Picture 4.41
Picture 4.41
4.15 Backup and Reset
Connect WIFI and login your google account, choose backup my data, system will backup
your data into google server.
37
Page 38
If you need to recovery factory reset, please click reset, as Picture 4 .42, if you need to
formulate NAND, please click reset tablet.
Picture 4.42
4.16 Date and Time
According to the preset, system will voluntorily apply the date, zone, and time provided by
internet.
Manual set date, timeand zone
1. Click Setting application procedure.
2. Slide down the screen, then click date and time.
3. Turn off “auto setting of date and time”.
4. Turn off “auto setting zone’.
5. Click Zone Selecting, then ch oose th e zone l ists. Slide down the list to view more
zones.
6. Click Date setting, then click upper or down buton to adjust date, month, and year,
click setting when you finish selection.
7. Click Time setting, then click upper or down button to adjust hour and minute, click
AM or PM to change morning or afternoon ( there is no such selection when you se
24-hour format).Click Setting to finish.
8. Click 24-hour format, switch between 12-hour or 24-hour formay, the time format you
choose will be usedon the alarmclock.
9. Click date format setting, then choose the time format you want to show on Tablet PC.
38
Page 39
Picture 4.43
Note: If you use the time internet p rovided, you will not able to set the date, ti me and time zone.
4.17 Fixed-time Startup and Shutdown
1.Click Setting application procedure
2.Click fixed-tine startup and shutdown.
3.Operate as below Picture 4.61
Turnon/off
Click it into
fixed-time
startup
setting
Click it into
fixed-time
shutdown
setting
fixed-time
startup
Turnon/off
fixed-time
shutdown
Picture 4.44
39
Page 40
4.18Assisstance Function
4.18-1. Large size
Click it to make system font large size
4.18-2. Click power button to end calls
When Click call, press “power” button, call will end b ut not hold.
4.18-3. Touch and hold delay
Click touch and hold delay to increae time, as Picture 4.45
Picture 4.45
4.18-4 Install webpage script
It will allow you install webpage scrip when you open system,, but it will increase the risk
when you are browsing webpage.
4.19 Engineer Selection
4.19-1 USB adjustment
After opening USB adjustment, you can use some softwa re to read Tablet PCsoftware, but
when USB adjustment is turned on, USB storage needs to manual adjust.
4.19-2 Keep awaken state
If you open keep awaken state, it wll never auto sleep when your Tablet PCis charging.
4.19-3 Pointer Location
If you open pointer location, it will display touch vertical and horizontal direction.
4.19-4 Show touches
40
Page 41
If you open display touch screen operation, it will display touch opeation on the screen. It is
suggested to use with same direction as pointer location.
4.19-5 Show screen update
If you open screen refresh, it will display related area when the area is refreshing.
4.19-6 Show CPU usage
After open CUP usage, in the right top of Tablet PC will show CPU usage situation.as Picture
4.46
4.20 About Tablet
Check Tablet PC state
1.CheckSetting application.
2.Click about tablet,checkstate message, model, Android version, version
No and so on.
3.Click state message, check battery state, battery volumne, SIM state,
IMEI number, IP address.
Picture 4.46
41
Page 42
42
Page 43
5 Multi-Media
5.1 Music
Enter into music player: in menu or desktop click musicicon to enter into music
player, click the music you want to play, as Picture 5.1:
Album
Artist
Album
Song name
Previous song
Picture 5.1
Random play
Next song
Pause/play
Picture 5.2
43
Page 44
Drag the progress bar to adjust play progress.
Operation of music player button as Picture 5.2
5.2 Photo Gallery
Photo gallery application can auto search photos and video files in SD card, and photo
gallery will classify these photos and videos in folder. You can apply photo gallery to
view and edit photos, set the photos as wallpaper and watch the video.
View pictures
1.Click gallery application in main interface.
2.Enter into gallery, click the folder you wantto view.
3.Click the picture you want to view, the system will play it in full screen mode
automatically.
4.The pictures can be zoom in and zoom out, put two fingers on the screen, the
separete the fingers(gather up the fingers, the picture will be zoom in) or
double click the screen.
Note: when you browse the pictures, slide left or right to view more pictures.
Edit and set pictures
When check the pictures in full screen mode, click menu key to display menu
selection, you can choose the selection you need to edit and setting pictures.
Slide Show
1.Open a p icture, use virtual key to click menu key, display menu selection.
2.Click slide show, it will auto loop play(or choose
picture folder)
Crop
1. Click menu key to display menu selection.
2. Then click crop, click and drag related area to adjust the cropper.
3. Click cropper and drag it inside and outside to adjust the image.
4. After adjust the size you want, click crop.
button in
5. Ifyouwishtogiveuptocrop,clickcancel to return to picture browse.
Edit
1. Click menu key, display the menu selection.
2. Click edit.
3.Adjust teh brightness, style, color, antialias setting in selection.
44
Page 45
4.Click save.
5.Ifyouwanttogiveupedit,clickreturn key, click not to return to picture
browse.
5.3 Camera
In the main interface or desktop, click camera application procedure, enter into camera
Operation of camera ,Switch camera: choose Menu key, click switch front/back
camera, as Picture 5.4
normalCamera mode
movement locus
Viewthe pictures and vid eos
camera shooting mode
Camera Mode
Switch front/back
Sub menu
Click it to take pictures
Picture 5.4
5.4 FM Radio
Clickin the main interface or desktop to enter into FM radio interface:
Radio button operation instruction as Picture 5.5:
45
Page 46
Open speaker
Current
frequency
Exit FM
Save
button
Previous
channel
Picture 5.5
Save channels: Clickbutton in the main interface to save the channel,
Next channel
and the channel will be saved in channels list.
Note: You need to insert earphone as antenna when using FM radio, If no
antenna, your Tablet PC can’t search any frequency band.
46
Page 47
6 Communication Function
6.1 Phone
1ClickPhone application procedure
2Operate as Picture 6.1
Display
phone
numbers
Dial phone
numbers
Picture 6.1
6.2 Text Message
1 Enter into main menu, chooseapplication procedure.
47
Page 48
2Click“Edit new message”
Directly input
phone number
Menu(discard,insert
text and settings)
Add receiver
Send
message
Picture 6.2
6.3 Contact List
Click Contact listin the main interface, enter into the contact list as Picture 6.3
48
Page 49
Picture 6.3
Search contact: clickbutton, enter into search function
Add contact: clickbutton, enter into add contact interface.
49
Page 50
7 Internet
7.1 Browser
In case of Wi-Fi or mobile internet is connected well (Please refer to Chapter 4.1 for wireless and
internet setting), click IE browserin the main menu or desktop to enter the IE interface, as
Picture 7.1
Address
column
menu
Save bookmark
Picture 7.1
Click address bar to input the website, click start, enter into related webpage, then you can browse
the website information, as Picture 7.1.2 and you can click the menu you can refresh ,save to
bookmarks,,share page,bookmarks,,history and setting the webpage.
50
Page 51
Picture7.1.2
7.2 Email
Email application procedure contains email setting guide, you can add the external POP3 OR
IMAP email account of normal web email service provider (For instance, Yahoo, Gmail, Hotmail
and 163),as Picture 7.2
a. EmailSetting
Picture 7.2
51
Page 52
1. After you click the sending email icon, you can see the email setting guide,
which can help you to set.
2. Input your email address and password.
3. Click “Next step” button, choose your email type is POP3 or IMAP.
4. Click “Next Step” button to check whether the email box servicer can receive or
send emails
5. Input the email account and display the email subiject, and click finish.
6. If the email box is available, you will enter into your mail box automatically.
b. Delete the email account
You can delete setted POP3 or IMAP email account from your Tablet PC.
Click
。
1. Enterintoyourmailbox.
2. Press Menu key.
3. Click Account
4. Press the account you want to delete.
5. Click confirm to remove.
c. Send E-mail
1. Click
to display your mail box.
2. Click the inbox, it will refresh the new emails automatically; c lick it to read new
email.
3. Press Menu key. Menus will popup.
4. Click Edit
to enter into new email editing interface.
5. Input the receiver’s email address.
6. Input the subject and email content.
7. If you want to add attachment, click menu key, the menu popup.
8. Click “Attach file” (photo,music, video,contacts).
9. Click“send”tosendtheemailout.
52
Page 53
Picture 7.3
Click it and
Add
attachment
53
Page 54
8 Other Application Procedures
8.1 Clock
Click Clockprocedure, enter into below interface as Picture 9.1.
There are clock, picture, music and homepage buttons.
Set alarm
8.2 Calculator
1. Click.
2. Enter into the basic board of calculator.
3. Soft touch the numbers or operator in calulator to calculate.
Picture 8.1
54
Page 55
Pictuer8.2
8.3 File Manager
File manager will copy, cut, delete, rename the documents or the fo lder in the TF card, it also will
share the files, install apk etc.
In the main menu or desktop, click the document manager icon
manager.
RAM
External
SD card
Picture8.3
to enter into documents
a、 Copy, cut, delete, rename the files and folder: choose the fil e or folder, long pressthe file or
55
Page 56
folder to enter into the interface as Picture 8.4, you can operate the file or folder.
Picture8.4
b、Paste the copy or cut file: choose the file you want to paste, choose right top
into Picture 9.5, choose right top
icon to enter into Picture 9.6
Picture8.5
icon to enter
56
Page 57
Picture 8.6 三
C. Share file:choose any file, long press it, it will popup “share”, choose the share way you want
in the list
d、Install apk file:Choose the file suffixed .apk in the file manager, you can install the third part
software as reminder.
e、Build new folder: Choose the menu you want to build the file, clickicon in right top,
choose new folder, you can build new folder as reminder.
8.4 Recorder
In the main interface or desktop, click recorder iconto enter into record interface,
click record keyto start record. Click Stop keyto stop recording. Click Play key
to play the recorded sound. The system will auto remind you to use or abandon this record,
please choose it manually.
Play the record: choose the video player to play the recorded sound, choose the recorded sound in
the source manager, and click it to play.
2. Hold the applicationprocedure you need to install.
3.Itpopup install, click install apk.
4.Finish the installation as g uide, it will operate.
Note: The third party procedure searched from internet to use on the system are all suffixed
with .apk.
9.2 Uninstall
Uninstall application procedure
1. Click setting icon in main interface.
2. Click manage application procedure, list all the application procedures
insralled in the system.
3. Click the APK you want to uninstall, click uninstall.
4. Click confirm t o finish uninstallation.
Skill: The procedure manager installed by system has many convinent methods to uninstal
after opening procedure manager, click uninstall, it will list all the application procedures
installed by system.
59
Page 60
10 Troubles Shooting
1.The first startup ofTablet PC is slow
After the Tablet PC system upgraded, the first startup need to install the
pre-installed application softwares, the lead time is around 2-3 minutes, the
startup afterwards will be much quicker.
2.Tablet PCcan’t connect Wi-Fi
Make sure the wireless router of internet service can work in normal.
Ensure the Tablet PC and wireless router in certain distance, and no wall or
other barrier between them.
Ensure the user name and password both correct.
3.TabletPCfeels hot
When many application procedures a re used in meanwhile, or the brightness of
screen open to the lightest or under charging, Tablet PCmay feel fever. It is
normal.
4.Email can’t be set or Registeration of application procedure.
Ensure your i n te rnet is well connected.
Make sure your email setting way is correct.
Keep your system time and local time consitent.
5.The system is abnormal and can’t work.
When you i nstall some third party application procedure, it may cause abnormal
work, you can press Reset key(next to power port) to reset the system.
6.The webpage ca n’t be opened
Please keep the distance between from route to Tablet PCin effective
range.
Please restart WIFI and try again.
7. Tablet PC works terribly slow sometimes
It is normal phenomenon. Please turn off some application you don’t need in advanced task
management, or uninstall some third party application to release more system resource.
60
Page 61
11 FCCWarning
RF Exposure Information and Statement
The SAR limit of USA (FCC) is 1 .6 W/kg averaged over one gram of tissue. Device has also been
tested against this SAR limit.This device was tested for typical body-worn operations with the
back of the handset kept 0 mm from the body. To maintain compliance with FCC RF exposure
requirements, use accessories that maintain a 10mm separation distance between the user's body
and the back of the handset. The use of belt clips, holsters and similar accessories should not
contain metallic components in its assembly. The use of accessories that do not satisfy these
requirements may not comply with FCC RF exposure requirements, and should be avoided.
NOTE: This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable
protection against harmful interference in a residential installation.This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio co mmunications.However, there is no
guarantee that interference will not occur in a particular installation.If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help
- This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter.
61
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.