AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
1
Page 2
22" LCD Color Monitor AOC 2230FH
Important Safety Notice
Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The servi ce
procedures recommended by AOC and described in this service manual are effective methods of performin g service
operations. Some of these service operations require the use of tools specially designed for the purpose. The
special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIO NS and NOTICES which should be carefully read in
order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. AOC could not possibly know, evaluate and advise the service trade of all conceivable ways in
which service might be done or of the possible hazardous consequences of each way. Consequently, AOC has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not
recommended by AOC mu st first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, AOC Company will be referred to as AOC.
WARNING
Use of substitute replacement parts, which do not have the same, specified safet y characteristics might create
shock, fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from AOC.
AOC assumes no liability, express or implied, arising out of any unauthorized modification of design.
Servicer assumes all liability.
FOR PRODUCTS CONTAINING LASER:
DANGER-Invisible laser radiations when open AVOID DIRECT EXPOSURE TO BEAM.
CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION -The use of optical instruments with this product will increase eye hazard.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF
THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment person’s body is ground ed through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may
damage the panel.)
Model number 2230Fh
Driving system TFT Color LCD
Viewable Image Size 558mm diagoanl
LCD Panel
Resolution
Pixel pitch 0.282mm(H) x 0.282mm(V)
Video R, G, B Analog lnterface & Digital Interface, HDMI
Separate Sync. H/V TTL
Display Color 16.7M Colors
Dot Clock 165 MHz
Horizontal scan range 31 kHz - 83 kHz
Horizontal scan
Size(Maximum)
Vertical scan range 56 Hz - 76 Hz
Vertical scan Size(Maximum) 296.1mm
Optimal preset resolution 1680 x 1050 (60 Hz)
Highest preset resolution 1680 x 1050 (60 Hz)
Plug & Play VESA DDC2B/CI
Input Connector D-Sub & DVI-D,HDMI
Input Video Signal
Power Source 100~240VAC, 50/60Hz
Speakers 2 x 2W
Connector Type 15-pin Mini D-Sub & 24 pin DVI-D, 19 pin HDMI
Signal Cable Type Detachable
Dimensions & Weight:
Height (with base)
Width
Depth
Weight (monitor only)
Weight (with packaging)
Temperature:
Operating 0° to 40°
Non-Operating -20°to 60°
Humidity:
Operating 10% to 85% (non-condensing)
Active < 49 W
Standby < 2 W
416.8 mm
510.2 mm
219.6 mm
5.2kg
6.7 kg
Non-Operating 5% to 80% (non-condensing)
Altitude:
Operating 0~ 3000m (0~ 10000 ft )
Non-Operating 0~ 5000m (0~ 15000 ft )
4
Page 5
22" LCD Color Monitor AOC 2230FH
2. LCD Monitor Description
The LCD Monitor will contain main board, power board, key board which house the flat panel control logic,
brightness control logic and DDC.
The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips
each voltage.
Monitor Block Diagram
CCFT Drive.
Flat Panel and
CCFL backlight
(Include adapter and inverter)
Power Board
Main Board
RS232 Connector
For white balance
adjustment in
factory mode
Key board
AC-IN
100V~240V
HOST Computer
Video signal, DDC
5
Page 6
22" LCD Color Monitor AOC 2230FH
3. Operation Instructions
3.1 General Instructions
Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor
(See Figure ). By changing these settings, the picture can be adjusted to your personal preferences.
* The power cord should be connected.
* Press the power button to turn on the monitor. The power indicator will light up.
3.2 Control Buttons
3.2.1 External Controls
1 Eco mode / Up 4 DCR / Right
2 Source(Auto) / Exit 5 Menu / Power
3 Volume /Left
3.2.2 Attaching the Cables
1. Power 4. Analog
2. HDMI 5. Audio
3. DVI 6. Earphone
6
Page 7
22" LCD Color Monitor AOC 2230FH
3.2.3 Attaching Wall Mounting Arm
Preparing to Install An Optional Wall Mounting Arm
This monitor can be attached to a wall mounting arm you purchase separately. Disconnect p ower before this
procedure. Follow these steps:
1. Remove the base.
2. Follow the manufacturer's instructions to assemble the wall mounting arm.
3. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the
back of the monitor.
4. Insert the 4 screws into the holes and tighten.
5. Reconnect the cables. Refer to the user's manual that came with the optional wall mounting arm for
instructions on attaching it to the wall.
7
Page 8
22" LCD Color Monitor AOC 2230FH
3.3 Adjust the Picture
OSD Settings
•Press the Menu (Power) button to activate the OSD window. Press left, right, up, down button to navigate
through the functions. Once the desired function is highlighted, press the Menu (Power) button to activate
sub-menu .
•In sub-menu, Press up, down button to navigate through the functions. Once the desired function is
highlighted, press
superior menu.
• If you want to adjust any other function, repeat steps 1-2.
• To exit OSD windows, select “exit” icon on main OSD, then press the Menu (Power) button .
• OSD Lock Function: To lock the OSD, press and hold the Left button while the monitor is off and then press
power button to turn the monitor on. To un-lock the OSD - press and hold the Left button while t he monitor is
off and then press power button to turn the monitor on.
•Eco Mode hot key (
no OSD ( Eco mode hot key may not be available in all models).
•Volume adjustment hot key : When there is no OSD , press Volume (
press or to adjust volume ( Only for the models with speakers).
• DCR hot key (
• Source hot key : When the OSD is closed, press Auto/Source button will be Source hot key function (Only
for the models with dual or more inputs) .Press Source button continuously to select the input source
showed in the message bar , press Menu button to change to the source selected.
•Auto configure hot key: When the OSD is closed, press Auto/Source button continuously about 2 second to
do auto configure.
•Press the Power button continuously about 2 second to turn off the monitor.
, button to button to change the setting. Press Menu (Power) button to return to
) : Press the Eco key continuously to select the Eco mode of brightness when there is
) to active volume adjustment bar,
) : Press DCR key continuously to active or disable DCR function when there is no OSD.
8
Page 9
22" LCD Color Monitor AOC 2230FH
Full Enhance: When "Full Enhance" is turned on, the color saturation of the entire screen is fully enriched, thus all
colors become more vibrant.
Nature Skin: When "Natural Skin" is turned on, the red and yellow colors are enriched automatically, thus presents
human skin with more natural and truer colors. "Natural Skin" setting is ideal for viewing human
portrait and detailed skin texture.
Green Field: When "Green Field" is turned on, the green color is enriched so that football field and mountain
landscape would look more natural and fresh. “Green Field” setting is ideal for watching mountain
scenery and outdoor sports.
Sky Blue: When"Sky Blue" is turned on, the color blue is being fine-tuned so that the sky or ocean landscape will
look more vivid and in-depth. "Sky Blue" setting is ideal for viewing sky and ocean images.
Auto Detect: When “Auto Detect” is turned on, every pigment will be detected and self-adjusted to render a lively
picture.
Demo: Screen divided into two for demonstration purposes.
Function Control Illustration
Luminance Adjust Range Description
Brightness 0-100 Backlight Adjustment
Contrast 0-100 Contrast from Digital-register.
Eco mode
Standard
Standard Mode
Text
Internet
Game Mode
9
Text Mode
Internet Mode
Page 10
22" LCD Color Monitor AOC 2230FH
Game
Movie
Sports
Gamma
DCR
Image Setup
Clock 0-100
Phase 0-100
H.Position 0-100
V.Position 0-100
Color Temp.
Warm
Normal
Cool
sRGB
User
Color Boost
Full Enhance on or off
Nature Skin on or off
Green Field on or off
Sky-blue on or off Disable or Enable Sky-blue Mode
AutoDetect on or off
Demo on or off Disable or Enable Demo
Pin No.Signal NamePin No.Signal NamePin No.Signal Name
1 TMDS Data 2- 9 TMDS Data 1- 17 TMDS Data 02 TMDS Data 2+ 10 TMDS Data 1+ 18 TMDS Data 0+
3 TMDS Data 2/4 Shield 11 TMDS Data 1/3 Shield19 TMDS Data 0/5 Shield
4 TMDS Data 4- 12 TMDS Data 3- 20 TMDS Data 55 TMDS Data 4+ 13 TMDS Data 3+ 21 TMDS Data 5+
6 DDC Clock 14 +5V Power 22 TMDS Clock Shield
7 DDC Data 15 Ground(for+5V) 23 TMDS Clock +
8 N.C. 16 Hot Plug Detect 24 TMDS Clock -
Please reinsert and make sure
the AC of 100-240 is no rmal
OK
Measure U103 PIN2=3.3V
U104 PIN2=1.8V
OK
Measure X401 oscillate
waveforms are normal
OK
NG
NG
NG
Reinsert or check the
Adapter/Inverter section
Check CN101 or replace
U103, U104
Replace X401
Replace U401
38
Page 39
22" LCD Color Monitor AOC 2230FH
p
No Picture
No picture
Check the signal cable
OK
NG
Change the signal cable
Measure U103 PIN2=3.3V
U104 PIN2=1.8V
OK
NG
Replace U103, U104
Measure X401 oscillate
waveform is normal
OK
NG
Replace X401
Check HS/VS from CN402
is normal
OK
Replace U401
NG
Check Correspondent
onent
com
39
Page 40
22" LCD Color Monitor AOC 2230FH
White Screen
White screen
Measure Q106 base
is high level?
NG
X401 oscillate
waveform is normal
OK
OK
NG
Replace X401
Check Q107 is broken or
CN404 solder?
Check reset circuit of
U401 is normal
Check Correspondent
component.
NG
OK
OK
Replace U401
NG
Check Correspondent
component.
Replace PANEL
40
Page 41
22" LCD Color Monitor AOC 2230FH
8.2.2 Power Board
1) No power
Check AC line volt 110V or 220V
OK
Check the voltage of C905 (+)
OK
Check start voltage for the pin3 of U901
OK
Check the auxiliary voltage is bigger than
10V and smaller than 20V
NG
NG
NG
Check AC input
Check bridge rectified circuit and F901 circuit
Check R904, R905, R906, Change U901
1) Check U901
OK
Check U901 pin8 PWM wave
OK
Check Q901/D900/D903
NG
NG
2) Check R906/D908 circuit
Check U901
41
Page 42
22" LCD Color Monitor AOC 2230FH
2.) No Backlight
Check C811=16V ?
NG
OK
Check ON/OFF signal
NG
OK
Check U801 PIN12=16V
OK
NG
Check adapter circuit
Check Interface or main board
Change on/off circuit
Check U801 PIN5/6 have triangle wave
NG
OK
Check U801 PIN9/10 PWM wave
OK
Check Q804, Q809 Drain wave
OK
NG
NG
Change U801
Check U801
Check Q810/Q805/Q811/Q806
Check the output of T801, T802
NG
OK
Check connecter & lamp, feedback and protect circuit
42
Change T801, T802
Page 43
22" LCD Color Monitor AOC 2230FH
8.2.3 Key Board
OSD is unstable or not working
Is Keypad board connecting normally?
OK
Is Button Switch normally?
OK
Is Keypad board normally?
OK
NG
Connect Keypad Board
NG
Replace Button Switch
NG
Replace Keypad Board
Check main board
43
Page 44
22" LCD Color Monitor AOC 2230FH
9. White- Balance, Luminance Adjustment
Approximately 30 minutes should be allowed for warm up before proceeding White-Balance adjustment.
1. How to do the Chroma-7120 MEM .Channel setting
A. Reference to chroma 7120 user guide
B. Use “SC” key and “NEXT” key to modify xyY value and use “ID” key to modify the TEXT description Following is
the procedure to do white-balance adjust
2. Setting the color temp. You want
A. 9300 color:
9300 color temp. parameter is x = 283 ±25, y = 297 ±25, Y = 180 ±25 cd/m
B. 7300 color:
7300 color temp. parameter is x = 297 ±25, y = 316 ±25, Y = 180 ±25 cd/m2
C. 6500 color:
6500k color temp. parameter is x = 313 ±25, y = 329 ±25, Y = 180 ±25 cd/m2
D.SRGB
SRGB color temp. parameter is x = 313 ±25, y = 329 ±25, Y = 150 cd/m
2 ,
2
3. Enter into factory mode of 2217V
Turn on power, press the Menu button, pull out the power cord, and then plug the power cord. Then the factory
OSD will be at the left top of the panel.
4. Bias adjustment:
Set the Contrast
to 90
Adjust the Brightness to 100.
5. Gain adjustment :
Move cursor to “-F-” and press MENU key
A. Adjust 9300k color-temperatu re
1. Switch the Chroma-7120 to 9300k channel.
2
2. The chroma 7120 will show x = 283 ±25, y = 297 ±25, Y = 180 ±25 cd/m
3. Switch the chroma-7120 to RGB MODE (with press “MODE” button to change)
4. Adjust the RED on factory windo w until chroma 7120 indicator reached the value R=100
5. Adjust the GREEN on factory window until chroma 7120 indicator reached the value G=100
6. Adjust the BLUE on factory window until chroma 7120 indicator reached the value B=100
7. Repeat above procedure (item 4, 5, 6) until chroma 7120 RGB value meet the tolerance =100±2
B. Adjust 7300k color-temperature
1. Switch the chroma-7120 to 7300k channel.
2
2. The chroma 7120 will show x = 297 ±25, y = 316 ±25, Y = 180 ±25 cd/m
3. Switch the chroma 7120 to RGB MODE (with press “MODE” button to change)
4. Adjust the RED on factory windo w until chroma 7120 indicator reached the value R=100
5. Adjust the GREEN on factory windo w until chroma 7120 indicator reached the value G=100
6. Adjust the BLUE on fact ory window until chroma 7120 indicator reached the value B=100
7. Repeat above procedure (item 4, 5, 6) until chroma 7120 RGB value meet the tolerance =100±2
44
Page 45
22" LCD Color Monitor AOC 2230FH
C. Adjust 6500k color-temperature
1. Switch the chroma-7120 to 6500K channel.
2
2. The chroma 7120 will show x = 313 ±25, y = 329 ±25, Y = 180 ±25 cd/m
3. Switch the chroma 7120 to RGB MODE (with press “MODE” button to change)
4. Adjust the RED on factory windo w until chroma 7120 indicator reached the value R=100
5. Adjust the GREEN on factory windo w until chroma 7120 indicator reached the value G=100
6. Adjust the BLUE on factory wind ow until chroma 7120 indicator reached the value B=100
7. Repeat above procedure (item 4, 5, 6) until chroma 7120 RGB value meet the tolerance =100±2
D. Adjust SRGB color-temperature
1. Switch the chroma-7120 to SRGB channel.
2. The chroma 7120 will show x = 313 ±25, y = 329 ±25, Y = 150cd/m
3. Switch the chroma 7120 to RGB MODE (with press “MODE” button to change)
4. Adjust the RED on factory windo w until chroma 7120 indicator reached the value R=100
5. Adjust the GREEN on factory windo w until chroma 7120 indicator reached the value G=100
6. Adjust the BLUE on factory wind ow until chroma 7120 indicator reached the value B=100
2
7. Repeat above procedure (item 4, 5, 6) until chroma 7120 RGB value meet the tolerance =100±2
E. Press reset key and Turn the Powe r-button “off to on” to quit from factory mode.
45
Page 46
22" LCD Color Monitor AOC 2230FH
10. Monitor Exploded View
46
Page 47
22" LCD Color Monitor AOC 2230FH
11. BOM List
TC8MM8NKWCA1DN
Location Part No. Description
040G 581 26704 SHIPPING LABEL
040G 58162461A EPA LABEL
041G 68508 A CONTROL CARD
044G6000 4 6B PAPER BOARD
044G6002821 1A PAPER BOARD
044GH600 1 HANDLE 2
045G 77 3 PE PACKING
050G 600 4 HANDLE 1
052G 1150 C INSULATING TAPE
052G 1186 SMALL TAPE
052G 1207 A ALUMINIUM TAPE
052G 1211 B AL TAPE
052G6019 1 INSULATING TAPE
070GHDCP500HDC HDCP CODE
078G311A500 G SPK 4 OHM 3.5 W 57.5X23.1MM 390MM
089G 184GAA500 HDMI CABLE
089G 725HAA DB D-SUB
089G1745HAA AC DVI CABLE
089G179J30N518 FFC CABLE
089G402A15N IS POWER CORD
095G8014 6X 51 HARNESS 6P-6P 216MM
0M1G 130 5120 SCREW
0M1G 930 6120 SCREW
0M1G1730 6120 SCREW,42-D020523
0M1G1730 6120 SCREW,42-D020523
0M1G1740 10 47 CR3 SCREW
705GQ834148 22" LCD STAND ASS'Y
0M1G 340 10 47 CR3 SCREW
A34G0690AEP 1B STAND
A37G0069 1 HINGE ASS’Y
705GQ834149 22" LCD BEZEL ASS'Y
A19G0004 1 SPRING-POWER
A33G0349 X2 1L BEZEL DECO
A33G0350 X2 1L FUNCTION BUTTON
A33G0351 KGA1C POWER BUTTON
A33G0352 1 1C POWER LENS
A34G0687AEPA1X 30 BEZEL(22")
E750 750GLMC0Z1312N PANEL M220Z1-L03 C1 NB CMO
A15G0380101 MAINFRAME
A33G0353AEP 1X CABLE CLIP MGT
A34G0688ABJ 1B REAR COVER(L22WA-830)
A34G0689AEP 1X 30 VESA COVER
A34G0691AEP 1X 33 BASE
A34G0693AEP 1X STAND COVER BACK
CBPC8MM8A1Q1 MAIN BOARD G2808-1-X-X-3-080401
040G 45762412B CBPC LABEL
C630 067G305V229 3 EC CAP 2.2UF M 16V 5*11
CN601 088G 30255S PHONE JACK TWO LAYER 3.5MM 5P BLK
CN402 088G 35315F H D-SUB 15PIN
CN403 088G 35424F C DVI 24PIN CONN
X401 093G 2253B J 14.31818MHZ/85C
C114 067G 305100 3T 10UF 16V
C401 067G 305100 3T 10UF 16V
C402 067G 305100 3T 10UF 16V
C412 067G 305100 3T 10UF 16V
C414 067G 305100 3T 10UF 16V
C439 067G 305100 3T 10UF 16V
C465 067G 305100 3T 10UF 16V
C503 067G 305100 3T 10UF 16V
C602 067G 305100 3T 10UF 16V
C611 067G 305100 3T 10UF 16V
C632 067G 305100 3T 10UF 16V
C633 067G 305100 3T 10UF 16V
C102 067G 305101 3T 100UF 16V 105C
C466 067G 305101 3T 100UF 16V 105C
C116 067G 305101 3T 100UF 16V 105C
C637 067G 305221 4T 6T 810 1 LG220UF 25V
C638 067G 305221 4T 6T 810 1 LG220UF 25V
C604 067G 3052293PT
C105 067G215B101 3T
C109 067G215B101 3T
C463 067G305M220 7T
U401 056G 562569 IC TSUMO58GDJ-LF PQFP-128
U104 056G 563930 IC AIC1117A-18PE SOT-252
U103 056G 585 4A IC AP1117E33L-13
U602 056G 628 8 IC FSA2257MTCX TSSOP-14
U504 056G 634 13 IC FSHDMI08MTDX TSSOP-56
U502 056G 662 10 IC RCLAMP0524P.TCT
U501 056G 662 10 IC RCLAMP0524P.TCT
U505 056G 662 13 IC AZC099-04S SOT23-6L
U601 056G1124 3 IC PCM1754DBQR SSOP-16
U403 056G1133 32 IC M24C04-WMN6TP SO8
U405 056G1133 84 AF24BC02-S1
U406 056G1133 84 AF24BC02-S1
U503 056G1133 84 AF24BC02-S1
U402
Q501 057G 417 12 T KEC 2N3904S-RTK/PS
Q503 057G 417 12 T KEC 2N3904S-RTK/PS
Q506 057G 417 12 T KEC 2N3904S-RTK/PS
Q505 057G 417 12 T KEC 2N3904S-RTK/PS
Q504 057G 417 12 T KEC 2N3904S-RTK/PS
Q404 057G 417 12 T KEC 2N3904S-RTK/PS
056G1133120(WA8M8PCMDQ1)
ELCAP 105℃ 470UF M 16V
EC 105℃ CAP 2.2UF M 16V
CAP 105℃ 100UF M 16V
CAP 105℃ 100UF M 16V
105℃ 22UF M 50V
040G 45762412B CBPC LABEL
CN804 033G8021 2E U INVERT CONNECTOR
CN803 033G8021 2E U INVERT CONNECTOR
CN802 033G8021 2E U INVERT CONNECTOR
CN801 033G8021 2E U INVERT CONNECTOR
E.C 105℃ CAP 470UF M 25V ED SERIES
E.C 105℃ CAP 470UF M 25V ED SERIES
CAP 105℃ 680UF M 25V
CAP 105℃ 680UF M 25V
105℃ 1000UF M 16V
105℃ 1000UF M 16V
EC 105℃ CAP 1000UF M 25V
EC 105℃ CAP 470UF M 16V
Q36G 600517 DUSTER CLOTH
Q40G 22N61553A RATING LABEL
Q40G0001624 4A PALLET LABEL
Q40G000262469A POP LABEL FOR 2230FH
Q40G0002850 9A VISTA LABEL
Q41G780A61587A QSG
Q44G6002132108 PAPER BOARD
Q44G9003220 CORNER PAPER
Q44GC043101 EPS
Q44GC043201 EPS
Q44GC043615 4A 22"LCD CARTON
Q45G 88606 R PE BAG FOR BASE
Q45G 88609130 EPE BAG
Q52G 1185 66 BIG TAPE FOR AOC CARTON
089G 17356G553 AUDIO CABLE 1800MM
Q41G780A61592A NA WARRANTY CARD
Q41G780A61593A EASE CARD
Q45G 76 28 RN R PE BAG MANUAL
Q70G220161521A CD MANUAL
040G 58162435A P/N LABEL
Q26G 800504 2 BAR CODE LABEL
POWER BOARD
PCB,FR-1,94V-0,T1.6MM,160*160MM
59
Page 60
22" LCD Color Monitor AOC 2230FH
12. Different Parts List
Diversity of TC8MM8NQWCA15N compared with TC8MM8NKWCA1DN
Location
026G 800504 3 BARCODE LABEL FOR 4
040G 154501 1 HI-POT GND LABEL
040G 581 26646 EANCODE LABEL
044G6000 4E CARTON
045G 77500 BARCODE RIBBON
051G6001 2 DESICCANT
052G6026 1 MESH PRINTTING PAPER
052G6026 2 MESH PRINTTING PAPER
089G402A15NIS1 POWER CORD
A15G0380101CKD MAINFRAME
A34G0687AEPA1X BEZEL(22")
A34G0689AEP 1X VESA COVER
A34G0691AEP 1X BASE
A34G0693AEP 1X STAND COVER BACK
A37G0069 1CKD HINGE ASS'Y
Q40G 22N61549A RATING LABEL
Q40G000262452A DEEVO STICK
Q41G780A61566A WARRANTY CARD
Q45G 76 28CK2 R PE BAG
Q45G 88606CK2 R PE BAG FOR BASE
Q52G 1185 98 MIDDLE CARTON TAPE FOR AOC
040G 581 26646 EANCODE LABEL
Q44G600019S 2A GP CARTON
040G 581 26646 EANCODE LABEL
045G 88525 B PE BAG
Q44G600024D 1A CARTON FOR MAIN BOARD
040G 581 26646 EANCODE LABEL
Q44G6000 TV 1A GP CARTON
Q45G 99606 24 ESD INSULATING PE BAG
Part No. Description
60
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.