AOC 193FWK User Manual

1
TABLE OF CONTENTS
FOR YOUR SAFETY --------------------------------------------------1
SAFETY PRECAUTIONS -------------------------------------- 2 SPECIAL NOTES ON LCD MONITORS ------------------- 3
BEFORE YOU OPERATE THE MONITOR --------------------- 3
FEATURES -------------------------------------------------------- 3 PACKING LIST --------------------------------------------------- 3 INSTALLATION INSTRUCTIONS ---------------------------4 CONTROLS AND CONNECTORS -------------------------- 5 ADJUSTING THE VIEWING ANGLE ----------------------- 6
OPERATING INSTRUCTIONS ------------------------------------- 7
GENERAL INSTRUCTIONS ---------------------------------- 7 HOW TO ADJUST A SETTING ------------------------------ 9 ADJUSTING THE PICTURE ----------------------------- 10-11 PLUG AND PLAY ----------------------------------------------- 12
TECHNICAL SUPPORT(FAQ) ------------------------------------ 13
ERROR MESSAGE & POSSIBLE SOLUTION -------- 14
APPENDIX -------------------------------------------------------------- 15
SPECIFICATIONS ------------------------------------------15-16 FACTORY PRESET TIMING TABLE ---------------------- 17 CONNECTOR PIN ASSIGNMENT ------------------------- 18
2
Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference.
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE:
1. The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in
order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference.
As an ENERGY STARPartner our company has determined that this product meets the ENERGY STARguidelines for energy efficiency.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously high voltages are present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.
SAFETY: Lamp Disposal
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE INFORMATION, CONTACT THE
3
ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG.
4
PRECAUTIONS
Do not use the monitor near water, e.g. near a bathtub, washbowl,
kitchen sink, laundry tub, swimming pool or in a wet basement.
Do not place the monitor on an unstable cart, stand, or table. If the
monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.
Slots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.
The monitor should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with
a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug.
Unplug the unit during a lightening storm or when it will not be used for
long period of time. This will protect the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result
in fire or electric shock.
Never push any object into the slot on the monitor cabinet. It could short
circuit parts causing a fire or electric shock. Never spill liquids on the monitor.
Do not attempt to service the monitor by yourself; opening or removing
covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel.
To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked between 100 - 240V AC, Min. 5A.
The wall socket shall be installed near the equipment and shall be easily
accessible.
For use only with the attached power adapter (Output 12Vdc) which have
UL, CSA listed license.
5
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a problem.
NOTES
Due to the nature of the fluorescent light, the screen may flicker during
initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
The LCD screen has effective pixels of 99.99% or more. It may include
blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the time.
Due to the nature of the LCD screen, an afterimage of the previous
screen may remain after switching the image when the same image has been displayed for a long time. The monitor will slowly recover from this.
BEFORE YOU OPERATE THE MONITOR
FEATURES
19” (48cm) Wide screen TFT Color LCD Monitor Crisp, Clear Display for Windows Recommened Resolutions: 1440 X 900@60Hz EPA ENERGY STAR
®
Dual Input (DVI + Analog) Ergonomic Design Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
1. LCD Monitor
2. Owner's Manual
3. Power Cord
4. D-Sub Cable
5. DVI Cable
6. External Adapter
6
INSTALLATION INSTRUCTIONS
SWIVEL BASE
Install Remove
Figure 1 Installing and Removing the Swivel Base
POWER CORD Power Source:
1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an External universal power supply that allows
operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.)
3. Connect the AC-power cord into your LCD monitor’s External Adapter
input socket, and then plug the other end of External adapter to LCD monitor’s DC-power-input. The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor.
NOTES
A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G
0.75mm2 or H05VVH2-F2 3G 0.75mm2) shall be used. Alternative a flexible cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G
0.75mm2) shall be used.
7
CONTROLS AND CONNECTORS Connecting Cables
Turn off your computer before performing the procedure below.
1. Connect the power adapter dc cable to the DC-In port on the back of the
monitor.
2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and
connect the other end to the computer’s D-Sub port.
3. Plug the power cable of your monitor into a nearby outlet. Plug the other
end of the power cord into the power adapter.
4. (Optional – Requires a video card with DVI port) - Connect one end of the
24-pin DVI cable to the back of the monitor and
connect the other end to the computer’s DVI port.
5. Turn on your monitor and computer. If you monitor diplays an image,
installation is complete. If not, refer to the FAQ (frequently asked questions) section for troubleshooting.
Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied).
Figure 2 Connecting Cables
1. DC-Jack Power Cable
2. D-sub Cable
3. AC Power Cord
4. DVI Cable
8
ADJUSTING THE VIEWING ANGLE
For optimal viewing it is recommended to look at the full face of the
monitor, then adjust the monitor’s angle to your own preference.
Hold the stand so you do not topple the monitor when you change the
monitor’s angle.
You are able to adjust the monitor’s angle from -5 to 20.
Figure 3
NOTES
Do not touch the LCD screen when you change the angle. It may cause
damage or break the LCD screen.
Careful attention is required not to catch your fingers or hands when you
change the angle.
9
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences.
The power cord should be connected. Connect the video cable from the monitor to the video card. Press the power button to turn on the monitor position. The power
indicator will light up.
Figure 4 External Control Button
EXTERNAL CONTROLS
1. Power Key 2. LED
3. MENU/ENTER 4. Luminance
5. Brightness Preset 6. Auto Adjust Key/Exit
10
FRONT PANEL CONTROL
Power Button:
Press this button to switch ON/OFF of monitor’s power.
MENU / ENTER :
Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Brightness/ Contrast Adjust OSD status.
Luminance :
Adjust contrast and brightness or function adjust. *Only adjustable at “STD” mode (see Brightness Preset below)
Brightness Preset:
Switch between “STD”, “OFFICE” & “VIVID”.
Auto Adjust button / Exit:
1. When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu).
2. When OSD menu is in off status, press this button over 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus.
Power Indicator:
Blue Power On mode.
Orange — Off mode. OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while the monitor is off and then press power button to turn the monitor on.
NOTES
Do not install the monitor in a location near heat sources such as
radiators or air ducts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock.
Save the original shipping carton and packing materials, as they will
come in handy if you ever have to ship your monitor.
For maximum protection, repackage your monitor as it was originally
packed at the factory.
To keep the monitor looking new, periodically clean it with a soft cloth.
Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety precaution, always unplug the monitor before cleaning it.
11
HOW TO ADJUST A SETTING
1. Press the MENU-button to activate the OSD window.
2. Press or to navigate through the functions. Once the desired
function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press or again to navigate
through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it.
3. Press or to change the settings of the selected function.
4. To exit and save, select the exit function. If you want to adjust any other
function, repeat steps 2-3.
Figure 5 The OSD Message
12
ADJUSTING THE PICTURE
Sub Menu
The descriptions for function control LEDS
Main
Menu
Item
Luminance
Image
Setup
Image
Position
Main
Menu
Icon
Sub
Item
Contrast Contrast from Digital-register.
Brightness Backlight Adjustment
Focus
Clock
H. Position
V. Position
Warm N/A
Menu
Icon
Adjust Picture Phase to reduce Horizontal-Line noise
Adjust picture Clock to reduce Vertical-Line noise.
Adjust the horizontal position of the picture.
Adjust the verticalposition of the picture.
Recall Warm Color Temperature from EEPROM.
Description
Color
Temp.
Input
Select
Cool N/A
sRGB N/A
User / Red Red Gain from Digital-register.
User / Green
User / Blue Blue Gain from Digital-register.
Analog N/A
Digital N/A
Recall Cool Color Temperature from EEPROM.
Recall sRGB Temperature from EEPROM.
Green Gain Digital-register.
Select input signal from analog source (D-Sub)
Select input signal from digital source (DVI)
13
Main
Menu Item
Main
Menu
Icon
Sub Menu
Item
Sub
Menu
Icon
Description
H. Position
OSD Setup
V. Position
OSD
Timeout
Language Language N/A Select the language you like.
Information Information N/A
Yes N/A
Reset
No N/A
Adjust the horizontal position of the OSD.
Adjust the verticalposition of the OSD.
Adjust the OSD timeout.
Show the resolution, H/V frequency and input port of current input timing.
Clear each old status of Auto­configuration .
Do not execute reset, return to main menu.
Exit N/A N/A Exit OSD
14
PLUG AND PLAY
Plug & Play DDC 2B Feature
This monitor is equipped with VESA DDC 2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC 2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC 2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video Electronics Standards Association (VESA) and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees (NUTEK). This feature is designed to conserve electrical energy by reducing power consumption when there is no video-input signal present. When there is no video input signal this monitor, following a time-out period, will automatically switch to an OFF mode. This reduces the monitor's internal power supply consumption. After the video input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to a "Screen Saver" feature except the display is completely off. The display is restored by pressing a key on the keyboard, or clicking the mouse.
USING THE RIGHT POWER CORD :
The accessory power cord for the Northern American region is the wallet plug with NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for the power cord shall be 125 volts AC. Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of a minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration. The other end terminates with a molded-on type connector
body, rated 10A, 250V, having standard CEE-22 female configuration. Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European counties.
15
TECHNICAL SUPPORT (FAQ)
make sure that none of the pins are
Problem & Question Possible Solution Power LED is not on *Check if the Power Switch is in the ON
position
*Power Cord should be connected
No Plug & Play *Check if the PC system is Plug & Play
compatible
*Check if the Video Card is Plug & Play
compatible
*Check if the D-15 plug pin of Video
Cable is bent
Picture is fuzzy *Adjust the Contrast and Brightness
Controls. Picture bounces or a wave pattern is present in the picture The power LED is ON (orange) but there’s no video or no picture.
Missing one of the primary colors (RED, GREEN, or BLUE)
Screen image is not centered or sized properly. Picture has color defects (white does not look white) Horizontal or vertical disturbances on the screen
*Move electrical devices that may cause
electrical interference.
*Computer Power Switch should be in
the ON position.
*Computer Video Card should be snugly
seated in its slot.
*Make sure monitor’s video cable is
properly connected to the computer.
*Inspect monitor’s video cable and make
sure none of the pins are bent.
*Make sure computer is operational by
hitting the CAPS LOCK key on the
keyboard while observing the CAPS
LOCK LED. The LED should either
turn ON or OFF after hitting the CAPS
LOCK key.
*Inspect the monitor’s video cable and
bent.
*Adjust pixel frequency (CLOCK) and
FOCUS or press hot-key (AUTO).
*Adjust RGB color or select color
temperature.
*Use win 95/98 shut-down mode Adjust
CLOCK and FOCUS or perform hot­key (AUTO-key).
CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width.
FOCUS adjusts the phase of the pixel clock signal. With a wrong phase adjustment the picture has horizontal disturbances in light picture.
For FOCUS and CLOCK adjustment use “dot-pattern” or win 95/98 shut­down mode pattern.
16
ERROR MESSAGE & POSSIBLE SOLUTION
CABLE NOT CONNECTED :
1. Check that the signal-cable is properly connected , If the connector is loose, tighten the connector’s screws.
2. Check the signal-cable’s connection pins for damage.
INPUT NOT SUPPORT :
Your computer has been set to unsuitable display mode ,set the computer to display mode given in the following table.(see page 17)
17
APPENDIX
SPECIFICATIONS
LCD Panel
Input
Display Colors Dot Clock Max. Resolution Plug & Play EPA ENERGY STAR
Driving system TFT Color LCD Size 48cm(19") Pixel pitch 0.285mm( H ) × 0.285mm( V )
R,G,B Analog InterfaceVideo
Digital Interface Separate Sync. H/V TTL H-Frequency 30kHz –83kHz V-Frequency 55-75Hz
16.2M Colors
135MHz
1440 × 900 @60Hz
VESA DDC 2B
®
ON Mode ≤36W
TM
Input Video Signal
Maximum Screen Size
Power Source Environmental
Considerations
Dimension Weight (N. W.)
OFF Mode ≤1W
15-pin D-SubInput Connector
DVI 24pin
Analog:0.7Vp-p(standard),
75 OHM, Positive
Digital signal
Horizontal : 410mm
Vertical : 256mm
100~240VAC,47~63Hz
Operating Temp: 5° to 50°C
Storage Temp.: -20° to 60°C
Operating Humidity :
10% to 85%
440×356×215 (W ×H×D)mm
4kg Unit (net)
18
Switch
Auto Adjust KeyBrightness Preset
LuminancePower ButtonMENU
External Controls: Functions Contrast
BrightnessFocusClockH. PositionV. Position(Warm)Color(Cool)Color sRGBRGB Color temperatureInput selectOSD SetupLanguage InformationResetExit
Power Consumption ( Maximum )
36 Watts
Regulatory Compliance
cULus, FCC, CE, TUV/S
19
Preset Display Modes
STANDARD
Dos-mode 720 × 400 31.47kHz 70.0Hz
VGA
SVGA
XGA
SXGA
WXGA+ 1440 × 900 55.935kHz 59.8Hz
RESOLUTION
640 × 480 31.47kHz 60.0Hz 640 × 480 37.50kHz 75.0Hz 800 × 600 37.879kHz 60.0Hz
800 × 600 46.875kHz 75.0Hz 1024 × 768 48.363kHz 60.0Hz 1024 × 768 56.476kHz 70.0Hz 1024 × 768 60.021kHz 75.0Hz
1280 × 1024 64.000kHz 60.0Hz 1280 × 1024 80.000kHz 75.0Hz
HORIZONTAL
FREQUENCY
VERTICAL
FREQUENCY
20
CONNECTOR PIN ASSIGNMENT
1 5 6
11 15
15 - Pin Color Display Signal Cable
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1. Red 9. +5V
2. Green 10. Detect Cable
3. Blue 11. Ground
4. Ground 12. DDC-Serial Data
5. Ground 13. H-Sync
6. R-Ground 14. V-Sync
7. G-Ground 15. DDC-Serial Clock
8. B-Ground
10
24 - Pin Color Display Signal Cable
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1. TMDS Data 2- 13. TMDS Data 3+
2. TMDS Data 2+ 14. +5V Power
3. TMDS Data 2/4 Shield
15. Ground(for+5V)
4. TMDS Data 4- 16. Hot Plug Detect
5. TMDS Data 4+ 17. TMDS Data 0-
6. DDC Clock 18. TMDS Data 0+
7. DDC Data
19. TMDS Data 0/5 Shield
8. N.C. 20. TMDS Data 5-
9. TMDS Data 1- 21. TMDS Data 5+
10. TMDS Data 1+ 22. TMDS Clock Shield
11. TMDS Data 1/3 Shield
23. TMDS Clock +
12. TMDS Data 3- 24. TMDS Clock -
21
Loading...