anvil international 383 User Manual

MALLEABLE IRON & CAST IRON FITTINGS

Malleable Iron Hex Bushing

FIGURE 383

q

Hex Bushing

Outside Hex – Type A

Inside Hex – Type B

See Cast Iron section on next
page for other available sizes.

Size

NPS DN Hex Type NPS DN lbs kg lbs kg

1

⁄8 6 0.12 0.05 0.12 0.05

1

⁄4 8 0.14 0.06 0.14 0.06

3

⁄8 10 0.11 0.05 0.11 0.05

1

⁄2 15 0.09 0.04 0.09 0.04

1

⁄8 6 0.24 0.11 0.24 0.11

1

⁄4 8 0.18 0.08 0.18 0.08

3

⁄8 10 0.18 0.08 0.18 0.08

1

⁄2 15 0.20 0.09 0.20 0.09

3

⁄4 20 0.16 0.07 0.16 0.07

1

⁄4 8 0.33 0.15 0.33 0.15

3

⁄8 10 0.27 0.12 0.27 0.12

1

⁄2 15 0.34 0.15 0.34 0.15

3

⁄4 20 0.39 0.18 0.39 0.18

3

⁄4 10

1 25

1

⁄4 32

1

A

A

A

A

B

B

B

A

A

B

B

B

A

Black Galv.

Unit Weight

A 1 25 0.30 0.14 0.30 0.14

1

⁄2 40 A 11⁄4 32 0.30 0.14 0.30 0.14

1

1

2 50 A 1

1

⁄2 65 A 2 50 1.02 0.46 1.02 0.46

2

⁄2 40 0.64 0.29 0.64 0.29

Note: Hexagon head or octagon head bushings 21⁄2 NPS

iron or steel. Face bushings 21⁄2 NPS
iron or steel. Face bushings 3NPS
used with 150# malleable iron and 125# cast iron. Solid plugs and face bushings are recommended for use with 250# and 300# fittings.

(65 DN)

(80 DN

) and larger reducing two sizes or more may be made of cast or malleable iron, ductile iron, or steel. According to specifications, hex bushings and cored plugs should be

(65 DN)

and smaller may be made of malleable iron, ductile iron or steel. Face bushings 3NPS

and smaller reducing one size may be made of malleable iron, ductile iron or steel. Other sizes may be made of cast iron, ductile iron, malleable

(80 DN

) and larger reducing one size may be made of malleable iron, ductile

Cast Iron Hex Bushings on next page.

PROJECT INFORMATION APPROVAL STAMP

Project:

Address:

Contractor:

Engineer: Remarks:

Submittal Date:

Notes 1:

Notes 2:

PF-6.13

Approved

q

Approved as noted

q

Not approved

q

MALLEABLE IRON & CAST IRON FITTINGS

Cast Iron Hex Bushing

q

FIGURE 383

Hex Bushing

Outside Hex

Type A

Inside Hex

Type B

Size

NPS DN Hex Type All Cast Iron NPS DN lbs kg lbs kg

1

/4 8 0.47 0.21 0.47 0.21

3

/8 10 0.47 0.21 0.47 0.21

1

/2 15 0.42 0.19 0.42 0.19

3

/4 20 0.47 0.21 0.47 0.21

11/2 40

A C

B C

B C

B C

Unit Weight

Black Galv.

A C 1 25 0.50 0.23 0.50 0.23

1

A C

A C

B C

2 50

B C

/4 8 0.75 0.34 0.75 0.34

3

/8 10 0.75 0.34 0.75 0.34

1

/2 15 0.70 0.32 0.70 0.32

3

/4 20 0.71 0.32 0.71 0.32

B C 1 25 0.73 0.33 0.73 0.33

1

/4 32 0.81 0.37 0.81 0.37

1

/2 15 1.28 0.58 1.28 0.58

3

/4 20 1.25 0.57 1.25 0.57

1

/4 32 1.24 0.56 1.24 0.56

1

/2 40 1.29 0.59 1.29 0.59

1

/2 15 1.93 0.88 1.93 0.88

3

/4 20 1.92 0.87 1.92 0.87

1

/2 65

2

A C 1

B C

B C

B C 1 25 1.16 0.53 1.16 0.53

B C 1

B C 1

B C

B C

B C 1 25 1.90 0.86 1.90 0.86

1

3 80

B C 1

B C 1

/4 32 1.77 0.80 1.77 0.80

1

/2 40 1.79 0.81 1.79 0.81

A C 2 50 1.90 0.86 1.90 0.86

1

A C 2

/2 65 1.63 0.74 1.63 0.74

B C 1 25 2.42 1.10 2.42 1.10

1

/4 32 2.56 1.16 2.56 1.16

1

/2 40 2.65 1.20 2.65 1.20

1

3

/2 80

B C 1

B C 1

B C 2 50 2.54 1.15 2.54 1.15

1

See Malleable Iron section on

previous page for other available sizes.

According to specifications, hex bushings and cored plugs should be used with 150# malleable iron and 125# cast iron. Solid plugs and face bushings are recommended for use with 250# and 300# fittings.

A C 2

A C 3 80 1.96 0.89 1.96 0.89

/2 65 3.23 1.46 3.23 1.46

Additional Cast Iron Hex Bushings on next page.

PF-6.13

MALLEABLE IRON & CAST IRON FITTINGS

Cast Iron Hex Bushing

FIGURE 383

Hex Bushing

Outside Hex

Type A

Inside Hex

Type B

See Malleable Iron section on

first page for other available sizes.

Size

NPS DN Hex Type All Cast Iron NPS DN lbs kg lbs kg

4 100

5 125

6 150

8 200

10 250

B

B

B

B

B

A

A

B

B

B

A

A

B

B

B

B

A

B

B

B

A

B

A

C 1 25 3.59 1.63 3.59 1.63

C 1

C 1

1

/4 32 3.54 1.61 3.54 1.61

1

/2 40 3.44 1.56 3.44 1.56

C 2 50 3.11 1.41 3.11 1.41

1

C 2

/2 65 3.29 1.49 3.29 1.49

C 3 80 3.15 1.43 3.15 1.43

1

C 3

/2 90 2.50 1.13 2.50 1.13

C 2 50 5.12 2.32 5.12 2.32

1

C 2

/2 65 4.87 2.21 4.87 2.21

C 3 80 4.83 2.19 4.83 2.19

1

C 3

/2 90 4.00 1.81 – –

C 4 100 3.94 1.79 3.94 1.79

C 2 50 8.00 3.63 8.00 3.63

1

C 2

/2 65 7.72 3.50 – –

C 3 80 7.75 3.51 7.75 3.51

C 4 100 6.83 3.10 6.83 3.10

C 5 125 5.24 2.38 5.24 2.38

C 3 80 15.50 7.03 – –

C 4 100 13.93 6.32 – –

C 5 125 13.65 6.19 – –

C 6 150 13.19 5.98 13.19 5.98

C 6 150 24.50 11.11 – –

C 8 200 22.00 9.98 – –

Unit Weight

Black Galv.

According to specifications, hex bushings and cored plugs should be used with 150# malleable iron and 125# cast iron. Solid plugs and face bushings are recommended for use with 250# and 300# fittings.

PF-6.13

MALLEABLE IRON FITTINGS

Malleable Iron Threaded Pipe Unions

Pressure - Temperature Ratings

Temperature

(°F) (°C) psi bar psi bar psi bar

-20°

150°

200° 93.3° 265 18.3 455 31.4 550 37.9

250° 121.1° 225 15.5 405 27.9 505 34.8

300° 148.9° 185 12.8 360 24.8 460 31.7

350° 176.7° 150 10.3 315 21.7 415 28.6

400° 204.4° 110 7.6 270 18.6 370 25.5

450° 232.2° 75 5.2 225 15.5 325 22.4

500° 260.0° – – 180 12.4 280 19.3

550° 287.8° – – 130 9.0 230 15.9

Note: Unions with Copper or Copper Alloy seats are not intended for use where temperature exceeds
450°F

For Listings/Approval Details and Limitations, visit our website at

-28.9°

to

to

65.6°

www.anvilintl.com or contact an Anvil Sales Representative.

Class 150 Class 250 Class 300

300 20.7 500 34.5 600 41.4

Pressure

Malleable Iron Threaded Fittings

Pressure - Temperature Ratings

Pressure

Temperature

(°F) (°C) psi bar psi bar psi bar psi bar

-20°
to

150°

200° 93.3 265 18.3 1,785 123.1 1,350 93.1 910 62.7

250° 121.1 225 15.5 1,575 108.6 1,200 82.7 825 56.9

300° 148.9 185 12.8 1,360 93.8 1,050 72.4 735 50.7

350° 176.7 150 10.3 1,150 79.3 900 62.1 650 44.8

400° 204.4 – – 935 64.5 750 51.7 560 38.6

450° 232.2 – – 725 50.0 600 41.4 475 32.8

500° 260.0 – – 510 35.2 450 31.0 385 26.5

550° 287.8 – – 300 20.7 300 20.7 300 20.7

Class 150

-28.9°
to

300 20.7 2,000 137.9 1,500 103.4 1,000 68.9

65.6°

Sizes 1⁄4"–1"

(6–25 mm)

Anvil Class 150/300 Malleable Iron Fittings conform to ASME
B16.3 and Unions conform to ASME B16.39.

ALL ELBOWS & TEES 3⁄8" (10 DN) and LARGER ARE 100% GAS TESTED AT
A MINIMUM OF 100 PSI. (6.9 bar)

Class 300

Sizes 11⁄4"–2"

(32–51 mm)

Sizes 21⁄2"–3"

(64–76 mm)

Standards and Specifications

Dimensions Material Galvanizing

****

Thread Pressure Rating Federal/Other

MALLEABLE IRON FITTINGS

Class 150/PN 20 ASME B16.3• ASTM A-197 ASTM A-153 ASME B1 20.1+ ASME B16.3• ASME B16.3**
Class 300/PN 50 ASME B16.3• ASTM A-197 ASTM A-153 ASME B1 20.1+ ASME B16.3•

MALLEABLE IRON UNIONS

Class 150/PN 20 ASME B16.39• ASTM A-197 ASTM A-153 ASME B1 20.1+ ASME B16.39• ASME B16.39***
Class 250 ASME B16.39• ASTM A-197 ASTM A-153 ASME B1 20.1+ ASME B16.39•
Class 300/PN 50 ASME B16.39• ASTM A-197 ASTM A-153 ASME B1 20.1+ ASME B16.39•

• an American National standard (ANSI), + ASME B1.20.1 was ANSI B2.1, ** Formerly WW-P-521, *** Formerly WW-U-531
**** ASTM B 633. Type I, SC 4, may be supplied as alternate zinc coating per applicable ASME B16 product standard.

PF-6.13

PF-11.13

CAST IRON FITTINGS

Anvil standard and extra heavy cast iron threaded fittings are
manufactured in accordance with ASME-B16.4 (except plugs
and bushings, ASME B16.14). Dimensions also conform to Federal
Specifications, WW-P-501 (except plugs and bushings WW-P-471).

For Listings/Approval Details and Limitations, visit our website at

www.anvilintl.com or contact an Anvil Sales Representative.

(°F) (°C) psi bar psi bar

-20° to 150° -28.9 to 65.6 175 12.1 400 27.6

200° 93.3 165 11.4 370 25.5

250° 121.1 150 10.3 340 23.4

300° 148.9 140 9.7 310 21.4

350° 176.7 125 8.6 300 20.7

400° 204.4 – – 250 17.2

Cast Iron Threaded Fittings

Pressure - Temperature Ratings

Temperature

Class 125 Class 250

Pressure

Standards and Specifications

Dimensions Material Galvanizing

****

Thread Pressure Rating Federal/Other

CAST IRON THREADED FITTINGS

Class 125 ASME B16.4• ASTM A-126 (A) ASTM A-153 ASME B1.20.1+ ASME B16.4• ASME B16.4■
Class 250 ASME B16.4• ASTM A-126 (A) ASTM A-153 ASME B1.20.1+ ASME B16.4• ASME B16.4■

CAST IRON PLUGS AND BUSHINGS

ASME B16.14• ASTM A- 126 (A) ASTM A-153 ASME B1.20.1+ ASME B16.14• WW-P-471

• an American National standard (ANSI), + ASME B1.20.1 was ANSI B2.1, ■ Formerly WW-P-501
**** ASTM B 633. Type I, SC 4, may be supplied as alternate zinc coating per applicable ASME B16 product standard.

PF-11.13

General Assembly of Threaded Fittings

1) Inspect both male and female components prior to assembly.

• Threads should be free from mechanical damage, dirt, chips and excess cutting oil.

• Clean or replace components as necessary.

2) Application of thread sealant

• Use a thread sealant that is fast drying, sets-up to a semi hard condition and is vibration resistant. Alternately, an anaerobic
sealant may be utilized.

• Thoroughly mix the thread sealant prior to application.

• Apply a thick even coat to the male threads only. Best application is achieved with a brush stiff enough to force sealant down
to the root of the threads.

3) Joint Makeup

• For sizes up to and including 2" pipe, wrench tight makeup is considered three full turns past handtight. Handtight engagement
for 1⁄2" through 2" thread varies from 41⁄2 turns to 5 turns.

• For 21⁄2" through 4" sizes, wrench tight makeup is considered two full turns past handtight. Handtight engagement for 21⁄2"
through 4" thread varies from 51⁄2 turns to 63⁄4 turns.

PF-11.13