Antec TPQ-1200 User Manual

U

SER’S

T

M

ANUAL

RUEPOWER QUATTRO

P

OWER SUPPLY

1200-W

ATT

U

SER’S

T

RUEPOWER QUATTRO SERIES

M

ANUAL

TPQ-1200 P

H

IGH-PERFORMANCE POWER SUPPLY

The TPQ-1200 goes beyond the kilowatt range of standard power supply units (PSUs) to power the largest servers
and video workstations. It includes six rails of +12V output to deliver safe and reliable power to your system, and
enough power and cables available to run three or more separate high-end graphics cards simultaneously.

S

TANDARDS AND FEATURES

The TruePower Quattro series is compatible with ATX12V v2.3 and EPS12V v2.91 specifications. The TPQ-1200 PSU
features Universal Input, which automatically senses when you connect the power supply to any AC power source
between 100~240V without having to worry about setting a voltage switch, and Active Power Factor Correction
(Active PFC), which improves the power factor value of the power supply by altering the input current wave shape,
thus helping transmission across the power grid.

C

ONTINUOUS POWER OUTPUT RATING

Unlike other power supplies that are rated by their peak wattage, Antec power supplies are rated based on their
continuous power output. This means that your TPQ-1200 delivers 1200-watt power during normal, continuous
operation; not simply at its peak

OWER SUPPLY

S

YSTEM PROTECTION

The TPQ-1200 also includes a variety of industrial-grade protective circuitry: OCP (Over Current Protection), OVP
(Over Voltage Protection), UVP (Under Voltage Protection), and SCP (Short Circuit Protection). Sometimes the PSU
will “latch” into a protected state. This means that you will need to clear the fault and turn the power off to the
PSU before it will function again. There are no user-replaceable fuses in your TPQ-1200.

80 PLUS® S

80 PLUS® certification is the most widely recognized independent standard in power supply efficiency. An 80
PLUS® certified power supply uses less energy and generates less heat to stay cooler, run quieter and last longer.
The TPQ-1200 earns the rare 80 PLUS® Silver level of efficiency, meaning that it has been certified to be at least
85% efficient at a wide range of operating loads; this will lower your operating costs and help protect the
environment.

ILVER CERTIFICATION

Source: 80 PLUS Verification and Testing Report

NVIDIA™ SLI™-R

Antec’s TruePower Quattro power supplies are NVIDIA™ SLI™-Ready certified for use with multiple high-end
graphics cards for superior parallel graphics processing.

A

DVANCED HYBRID CABLE MANAGEMENT SYSTEM

The TPQ-1200 uses Advanced Hybrid Cable Management. Cables that are important or mandatory are connected
directly to the PSU. There are also modular connectors on the back of the PSU to add additional cables as needed.
Using only the power cables you need will reduce clutter and improve airflow inside your case. For the list of
connected and optional cables, see Table 3.

DC

TO DC CONVERSION

The TPQ-1200 uses DC to DC conversion for the +5V and +3.3V rails. This module operates at 85% efficiency, as
opposed to traditional magnetic amplifiers that operate at only 75% efficiency. Transient response time is almost
100 times faster, providing remarkably stable power output in response to changing loads.

P

ULSE WIDTH MODULATION

Pulse Width Modulation technology allows the TPQ-1200 to finely control the speed of the PSU’s fan. By using this
method instead of the traditional voltage-controlled fans, this PSU’s fan can run up to 50% quieter than standard
fans. A PWM fan can run as slow as 10-15% of the fan’s rated top speed, whereas a voltage regulated fan can only
go as low as 40%.

EADY CERTIFICATION

(PWM) FAN

+12 V

The TPQ-1200 uses six separate +12 volt power rails. The engineers have allocated the rails to different connectors
to prevent voltage sags in one device due to sudden demands for power by another device.

OLT RAIL DISTRIBUTION

Table 1

Direct Cabling Connectors

8-pin (4 + 4) ATX12V, EPS 2

P

OWER OUTPUT

The TPQ-1200 distributes a varying maximum number of amps on each rail. To see the output capacity and
regulation for each different voltage, see Table 2.

+12V

Rail

24-pin main connector 3

8-pin EPS12V 2

PCI-E w/ blue stripe 3

PCI-E w/ green stripe 4

Molex cable from PSU 1

SATA cable from PSU 1

T

ABLE

2

Voltage Min. Load Max. Load Regulation Ripple & Noise

+3,3V 0A 25A -3% ~ +5% <50 mV

+5V 0A 30A -3% ~ +5% <50 mV
+12V1 0A 38A -3% ~ +5% <120 mV
+12V2 0A 38A -3% ~ +5% <120 mV
+12V3 0A 38A -3% ~ +5% <120 mV
+12V4 0A 38A -3% ~ +5% <120 mV
+12V5 0A 38A -3% ~ +5% <120 mV
+12V6 0A 38A -3% ~ +5% <120 mV

–12V 0A 0,5A -3% ~ +5% <120 mV

+5VSB 0A 6A -3% ~ +5% <50 mV

The continuous maximum total output power shall not exceed 1200W.
+12V1, +12V2, +12V3, +12V4, +12V5 and +12V6 DC maximum output power shall not exceed 1200W (100A).
+3.3V and +5V DC maximum combined output power shall not exceed 170W.

T

ABLE

3

Cable

Quantity

N/A

1

1

2

x 3

x 3

Connector

x 3

[Floppy img]

Molex connector

x1

Molex connectors

Part Name

Power Supply
Direct Cabling

and Floppy

connector w/

cable

w/ cable

Serial ATA

connectors w/

cable

Description

Motherboard

8-pin EPS12V

8-pin (4+4) ATX12V, EPS

Molex connectors and one Floppy connector

Includes three Serial ATA connectors

2 x 8-pin (6+2) PCI-E

3 x Molex + 1 x Floppy

3 x SATA

Includes three

Includes three Molex connectors

24-pin (20+4)

1

2

x 1 x 1

x 2

Serial ATA

connectors w/

PCI Express

connector w/

cable

cable

Includes two Serial ATA connectors

Includes one 6-pin and one 8-pin

(6 + 2) PCI Express connector

I

NSTALLATION

1. Install the TPQ-1200 PSU into your case with the four screws provided.

2. Connect the 24-pin main power connector to your motherboard.

:

3. Connect the 8-pin or 4-pin ATX12V connector for the CPU to the appropriate connector on your
motherboard. If your motherboard has an 8-pin socket with a cover on some of the openings, we
recommend that you remove the cover and use the 8-pin connector.
Note: Please also refer to your motherboard user’s manual for any special instructions.

4. Connect the cables from the cable pack to the socket on the power supply as needed. If you are going to
plug the additional PCI-E cable into the PSU, it should go into the red socket. If the red socket is not being
used for PCI-E, then it can be used for another cable from the pack that accompanies the PSU.

5. Connect the AC power cord to the power supply AC inlet. Please be sure to use the heavy-duty cord
supplied with your TPQ-1200.

Antec, Inc.

47900 Fremont Blvd.

Fremont, CA 94538

tel: [phone]

fax: [phone]

Antec Europe B.V.

Stuttgartstraat 12

3047 A Rotterdam

Netherlands

tel: [phone]

fax: [phone]

Technical Support:

US & Canada

1-800-22ANTEC

[e-mail]

Europe

[phone]

[e-mail]

www.antec.com

© Copyright 2009 Antec, Inc. All rights reserved.

All trademarks are the property of their respective owners.

Reproduction in whole or in part without written permission is prohibited.