Bluetooth Water Resistant Speaker
Power
The speaker operates on built-in rechargeable battery
To recharge the built-in battery, open the rubber cap on the back casing and connect micro
USB socket with PC through supplied USB cable
Charging: Red LED indicator turns on
Fully Charged: The red LED turns green when it is fully charged
Close the rubber cap firmly after charging.
Play from a Bluetooth device
Note: The effective operation range between the speaker and your Bluetooth device is
approximately 10 meters (33 feet) line of sight maximum
- Press [ON/OFF] button on back casing to turn on the speaker
- The blue LED indicator will flash
- Activate the Bluetooth function in your Bluetooth device
- Select “BT Speaker” on your Bluetooth device for pairing
- When connected, the blue LED indicator stays steadily on
- Start music play on your Bluetooth device
- Adjust volume on your Bluetooth device or press the [+] or [-] button on the speaker
- Press [Play/Pause] button on the speaker to play or pause music
- Press [Forward] or [Backward] on the speaker to select your music
- Press the [ON/OFF] button again to switch off the unit when it is not in use for power
saving. Blue LED indicator will turn off
Play from an external device
- Press the [ON/OFF] button to turn on the speaker
- Open the rubber cap on the back casing and connect your speaker with an external device
through a 3.5mm line-in cable
- Start music play on your device
- Press the [ON/OFF] button again to switch off the unit when it is not in use for power
saving
- Close the rubber cap firmly after use
Note: The speaker is not water resistant while playing music through a 3.5mm line-in cable
since the rubber cap needs to be open.
Specification
Rated output power: 1.6W RMS
DC Power input: USB: 5V, 500mA
Built-in rechargeable battery: 500 mAh
Bluetooth specification: V3.0 + EDR
Supported Bluetooth Profiles: AVRCP, A2DP
Range: maximum 10 meters (33 feet) line of sight
Water resistance level: IPX4 (protected against splashing water)
Working temperature: 0C – 50C
Troubleshooting
No power:
- Recharge your speaker
No Sound:
- Adjust volume on your Bluetooth device or the speaker
- Make sure that your Bluetooth device is connected with the speaker and they are within
the effective operation range
Care & Maintenance:
- Clean the unit with a damp (never wet) cloth. Solvents or detergents should never be used
- NEVER IMMERSE IN WATER
This product is not designed to be immersed in water or to come in continuous contact with
water since permanent damage to the electrical and mechanical parts will result
- Always wipe the outside of the cabinet thoroughly if it becomes wet with moisture or water
splashes. This will help to prevent the internal parts of the unit from entry of water and
possible moisture damage
- Always close the rubber cap on back casing firmly to protect the unit against water
splashes
- If sand gets inside the speaker grill, open the small rubber cap on the side of the back
casing and pour out the sand
Cautions:
1) Due to the used enclosure material, the device shall only be connected to a USB Interface
of version 2.0 or higher. The connection to so called power USB is prohibited
2) Caution Risk of explosion if battery is replaced by an incorrect type.
3) Dispose of used batteries according to the instructions
4) Do not expose the device to an extremely high electromagnetic filed, this may impair the
correct functioning of the device.
5) The normal function of the product may be disturbed by strong Electro-Magnetic
Interference. If so, simply reset the product to resume normal operation by following the
instruction manual. In case the function could not resume, please use the product in order
location.
FCC Statements
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However , there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct
The interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference, and This device must accept any interference received,
including interference that may cause undesired operation.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. such modifications could void the user’s authority to operate this
equipment.
Loading...