Series 37XXXC
Vector Network Analyzer
GPIB QUICK REFERENCE GUIDE
This manual supplements the 37XXXC Series Vector Network
Analyzer Programming Manual. Insert it behind the tab marked
Appendix B, GPIB Quick Reference Guide in that manual.
490 JARVIS DRIVE l MORGAN HILL, CA 95037-2809
P/N: 10410-00229
REVISION: D
PRINTED: MARCH 2004
COPYRIGHT 2004 ANRITSUCO.
WARRANTY
The ANRITSU product(s) listed on the title page is (are) warranted against defects in materials
and workmanship for one year from the date of shipment.
ANRITSU's obligation covers repairing or replacing products which prove to be defective during
the warranty period. Buyers shall prepay transportation charges for equipment returned to
ANRITSU for warranty repairs. Obligation is limited to the original purchaser. ANRITSU is not
liable for consequential damages.
LIMITATION OF WARRANTY
The foregoing warranty does not apply to ANRITSU connectors that have failed due to normal
wear. Also, the warranty does not apply to defects resulting from improper or inadequate
maintenance by the Buyer, unauthorized modification or misuse, or operation outside of the
environmental specifications of the product. No other warranty is expressed or implied, and the
remedies provided herein are the Buyer's sole and exclusive remedies.
TRADEMARK ACKNOWLEDGEMENTS
V Connector and K Connector are registered trademarks of ANRITSU Company.
Windows and Excel are registered trademarks of Microsoft Corporation.
NOTICE
ANRITSU Company has prepared this manual for use by ANRITSU Company personnel and
customers as a guide for the proper installation, operation and maintenance of ANRITSU
Company equipment and computer programs. The drawings, specifications, and information
contained herein are the property of ANRITSU Company, and any unauthorized use or
disclosure of these drawings, specifications, and information is prohibited; they shall not be
reproduced, copied, or used in whole or in part as the basis for manufacture or sale of the
equipment or software programs without the prior written consent of ANRITSU Company.
UPDATES
Updates to this manual, if any, may be downloaded from the Anritsu Internet site at:
http://www.anritsu.com
37XXXC VNA GPIB
Quick Reference Guide
Table of Contents
1. INTRODUCTION ....................3
2. GENERAL ........................3
37XXXC VNA GPIB
Quick Reference Guide
1. INTRODUCTION This appendix provides a quick reference to the 37XXXC GPIB Pro
gramming commands.
2. GENERAL This guide is divided into two listings: alphabetical and functional.
The alphabetical listing begins on page 5 and lists the commands al
phabetically with a brief description. The functional listing begins on
page 39 and lists the commands, a brief description, and the functional
group with the list sorted alphabetically by the functional group.
All of these commands are described in detail in Chapter 10 of the
37XXXC Programming Manual.
-
-
37XXXC GPIB QRG 3
ALPHABETICAL LISTING
Command Description
*CLS Clear status bytes and structures
*DDT Enter the 488.2 Define Device Trigger command string
*DDT? Output the 488.2 Define Device Trigger command string
*ESE Enter the 488.2 Standard Event Status Enable mask
*ESE? Output the 488.2 Standard Event Status Enable mask
*ESR? Output the 488.2 Standard Event Status Register value
*IDN? Output the 488.2 instrument identification string
*IST? Output the value of the ist message
*OPC Initiate the 488.2 Operation Complete sequence
*OPC? Initiate the 488.2 Operation Complete Query sequence
*OPT? Output the 488.2 options installed string
*PRE Enter the 488.2 Parallel Poll Register Enable mask
*PRE? Output the 488.2 Parallel Poll Register Enable mask
*RST Instrument reset
*SRE Enter the 488.2 Service Request Enable mask
*SRE? Output the 488.2 Service Request Enable mask
*STB? Output the 488.2 Status Byte value
*TRG Initiate a Group Execute Trigger sequence
*TST? Perform self test and output status
*WAI Wait to continue
A12 Simulate 12-term calibration
A8R Simulate 1-path 2-port calibration reverse path
A8T Simulate 1-path 2-port calibration forward path
ABORTCAL Abort calibration in progress and keep existing calibration data
ABT Simulate trans freq response calibration forward and reverse
ACAA Set AutoCal standard to assurance
ACADPL Enter AutoCal adapter length
ACADPL? Output AutoCal adapter length
ACADR Set AutoCal type to adapter removal
ACAL1R2 Set adapter removal port configuration to ADAPT & L=1 and R=2
ACAR1L2 Set adapter removal port configuration to ADAPT & R=1 and L=2
ACARP? Output AutoCal adapter removal port configuration
ACDEF Select default AutoCal isolation averaging factor
ACF2P? Output AutoCal full 2 port configuration
ACF2TC Set AutoCal 2 port thru type to calibrator
ACF2TT Set AutoCal 2 port thru type to true thru
ACF2TX? Output AutoCal 2 port thru type selection
ACHFD Save AutoCal characterization data to floppy disk
ACHHD Save AutoCal characterization data to hard disk
37XXXC GPIB QRG 5
ALPHABETICAL LISTING
Command Description
ACIAF Enter user AutoCal isolation averaging factor
ACIAF? Output user AutoCal isolation averaging factor
ACIAX? Output AutoCal isolation averaging factor omit/default/user selection
ACISO Enter AutoCal isolation averaging number
ACISO? Output AutoCal isolation averaging number
ACL1AR2 Set adapter removal port configuration to L=1 and ADAPT & R=2
ACL1R2 Set AutoCal full 2 port configuration to L=1 and R=2
ACLO Enter AutoCal load averaging number
ACLO? Output AutoCal load averaging number
ACLOAD Set AutoCal standard to load
ACOMIT Omit using AutoCal isolation averaging factor
ACOPEN Set AutoCal standard to open
ACP1? Output AutoCal S11 port configuration
ACP1L Set AutoCal S11 port configuration to left
ACP1R Set AutoCal S11 port configuration to right
ACP2? Output AutoCal S22 port configuration
ACP2L Set AutoCal S22 port configuration to left
ACP2R Set AutoCal S22 port configuration to right
ACPL Set AutoCal S11 port configuration to left
ACPR Set AutoCal S11 port configuration to right
ACR1AL2 Set adapter removal port configuration to R=1 and ADAPT & L=2
ACR1L2 Set AutoCal full 2 port configuration to R=1 and L=2
ACRFL Enter AutoCal reflection averaging number
ACRFL? Output AutoCal reflection averaging number
ACS11 Set AutoCal type to S11
ACS22 Set AutoCal type to S22
ACSF2P Set AutoCal type to full 2 port
ACSHORT Set AutoCal standard to short
ACSTD? Output AutoCal standard
ACSW Enter AutoCal switch averaging number
ACSW? Output AutoCal switch averaging number
ACTHRU Set AutoCal standard to thru
ACTU Enter AutoCal thru averaging number
ACTU? Output AutoCal thru averaging number
ACTUAVG Enter AutoCal thru update averaging number
ACTUAVG? Output AutoCal thru update averaging number
ACTULS Apply last thru update cal setup
ACX? Output AutoCal type
ADD Select addition as trace math for active channel
6 37XXXC GPIB QRG
ALPHABETICAL LISTING
Command Description
ADDFC Enter frequency counter GPIB address
ADDFC? Output frequency counter GPIB address
ADDPLT Enter plotter GPIB address
ADDPLT? Output plotter GPIB address
ADDPM Enter power meter GPIB address
ADDPM? Output power meter GPIB address
ADPL Enter electrical length for adapter removal
ADPL? Output electrical length for adapter removal
ADRIVE Select the floppy drive as the default drive
AFT Simulate transmission frequency response calibration forward path
AH0 Turn automatic DUT protection off
AH1 Turn automatic DUT protection on
AHX? Output automatic DUT protection on/off status
ALC Perform ALC loop internal calibration
AMKR Select active marker on all channels marker mode
ANNCOL Enter the color number for annotation and menu text
ANNCOL? Output the color number for annotation and menu text
AOF Turn averaging off
AOF? Output averaging on/off status
AON Turn averaging on
APR Enter group delay aperture setting on active channel
APR? Output group delay aperture setting on active channel
ARB Simulate reflection only calibration both ports
ARF Simulate reflection only calibration port 1
ARR Simulate reflection only calibration port 2
ART Simulate trans freq response calibration reverse path
ASC Autoscale the active channel display
ASP Enter polar stop sweep position angle
ASP? Output polar stop sweep position angle
AST Enter polar start sweep position angle
AST? Output polar start sweep position angle
ATTN Attach next segment and make the active segment
AVG Enter averaging count and turn on
AVG? Output averaging count
AVGCNT? Output the current sweep-by-sweep average sweep count
BBL Select broadband load for calibration
BBZ Enter broadband load impedance for calibration
BBZL Enter broadband load inductance for calibration
BC0 Turn CRT display off (disabled)
37XXXC GPIB QRG 7
ALPHABETICAL LISTING
Command Description
BC1 Turn CRT display on (disabled)
BCKCOL Enter the color number for background
BCKCOL? Output the color number for background
BCX? Output CRT display on/off status
BD1 Select band 1 for definition
BD2 Select band 2 for definition
BD3 Select band 3 for definition
BD4 Select band 4 for definition
BD5 Select band 5 for definition
BDMM Define Millimeter Wave band equations
BEEP0 Disable the instrument beeper on GPIB errors
BEEP1 Enable the instrument beeper on GPIB errors
BEEPX? Output GPIB beep on error enable/disable status
BEG Begin taking calibration data
BEGAC Start AutoCal
BEGCH Start AutoCal characterization
BEGN Begin next segment and make it the active segment
BEGTU Start AutoCal thru update
BH0 Turn bias off while in hold
BH1 Turn bias on while in hold
BHX? Output bias on/off during hold status
BMPB Select Black on White as bitmap type
BMPC Select Color on White as bitmap type
BMPT Select true color as bitmap type
BPF Enter break point frequency for 3 line LRL calibration
BRILL Activate color configuration Brilliant
BSP Enter band stop frequency
BSP? Output band stop frequency
BST Enter band start frequency
BST? Output band start frequency
BWL3 Set bandwidth loss value to 3 dB
BWLS Enter bandwidth loss value
BWLS? Output bandwidth loss value
C12 Select 12 term calibration
C8R Select 1-path 2-port calibration reverse path
C8T Select 1-path 2-port calibration forward path
CALR Perform receiver cal for gain compression testing
CAS Clear active segmented limit vertical/horizontal definitions
CBT Select trans freq response calibration forward and reverse
8 37XXXC GPIB QRG
Command Description
CC0 Enter capacitance coefficient 0 for open
CC1 Enter capacitance coefficient 1 for open
CC2 Enter capacitance coefficient 2 for open
CC3 Enter capacitance coefficient 3 for open
CCD Collect corrected data in an internal buffer
CD Change default directory
CDRIVE Select the hard disk as the default drive
CF1 Select female 1.0 mm connector for current port
CF2 Select female 2.4mm connector for current port
CF3 Select female GPC-3.5 connector for current port
CF716 Select female 7/16 connector for current port
CFC Select female TNC connector for current port
CFD Collect final data in an internal buffer
CFK Select female K connector for current port
CFN Select female Type N connector for current port
CFN75 Select Female type N 75-ohm connector for current port
CFS Select female SMA connector for current port
CFSP Select Special Female connector for current port
CFSPA Select Band A special female connector for current port
CFSPB Select Band B special female connector for current port
CFSPC Select Band C special female connector for current port
CFT Select trans freq response calibration forward path
CFV Select female V connector for current port
CH1 Make channel 1 the active channel
CH2 Make channel 2 the active channel
CH3 Make channel 3 the active channel
CH4 Make channel 4 the active channel
CHX? Output active channel number
CL0 Enter inductive coefficient 0 for short
CL1 Enter inductive coefficient 1 for short
CL2 Enter inductive coefficient 2 for short
CL3 Enter inductive coefficient 3 for short
CLASS Activate color configuration Classic
CLB Clear all multiple source band definitions
CLBMM Clear the new Millimeter Wave band definitions
CM Suffix sets distance data type and scales by 1E-2
CM1 Select male 1.0 mm connector for current port
CM2 Select male 2.4mm connector for current port
CM3 Select male GPC-3.5 connector for current port
ALPHABETICAL LISTING
37XXXC GPIB QRG 9
ALPHABETICAL LISTING
Command Description
CM716 Select male 7/16 connector for current port
CMC Select male TNC connector for current port
CMK Select male K connector for current port
CMN Select male N connector for current port
CMN75 Select Male type N 75-Ohm connector for current port
CMS Select male SMA connector for current port
CMSP Select Special Male connector for current port
CMSPA Select Band A special male connector for current port
CMSPB Select Band B special male connector for current port
CMSPC Select Band C special male connector for current port
CMT Suffix sets distance data type and scales by 1E-2
CMV Select male V connector for current port
CMX? Output calibration method
CND Select user specified connector for current port
CNG Select GPC-7 connector for current port
CNTR Enter center frequency
CNTR? Output center frequency
COF Turn error correction off
CON Turn error correction on
CON? Output error correction on/off status
COO Enter offset for open for user specified connector (Standard Calibration)
COPY Copy a files contents to another file
COS Enter offset for short for user specified connector
CRB Select reflection only calibration both ports
CRD Collect raw data in an internal buffer
CRF Select reflection only calibration port 1
CRR Select reflection only calibration port 2
CRT Select trans freq response calibration reverse path
CSB Clear status bytes and structures (same as *CLS)
CSF? Output cal start frequency
CSL Clear service log
CTF? Output cal stop frequency
CTN Continue sweeping from current point
CWC Select CW frequency calibration data points
CWD? Output current working directory string
CWDEC Subtract 1 from the current CW index
CWF Enter CW frequency and turn CW on
CWF2I? Output index for frequency given
CWF? Output CW frequency
10 37XXXC GPIB QRG
ALPHABETICAL LISTING
Command Description
CWI Enter index for CW frequency and turn CW on
CWI2F? Output frequency for index given
CWI? Output current index number
CWINC Add 1 to the current CW index
CWN2I Add N to the current CW index
CWON Turn CW on at current CW frequency
CWON? Output CW on/off status
CWP Enter number of points drawn in CW
CWP? Output number of points drawn in CW
CWSRT Set CW frequency to the start frequency
CWSTP Set CW frequency to the stop frequency
CXD? Output internal buffer data collection mode
CXX? Output calibration type
D13 Display channels1&3
D14 Display all four channels
D24 Select dual channel display with channels2&4
DA1 Select a1 = Ra as denominator for parameter being defined
DA2 Select a2 = Rb as denominator for parameter being defined
DAT Display data only on active channel
DAT? Output trace memory display mode
DATCOL Enter the color number for data
DATCOL? Output the color number for data
DATE Enter the system date
DATE? Output the system date
DB Suffix sets power data type
DB1 Select b1 = Ta as denominator for parameter being defined
DB2 Select b2 = Tb as denominator for parameter being defined
DBL Suffix sets power data type
DBM Suffix sets power data type
DBP Select distance bandpass mode for active channel
DC1 Display channel 1 and 2 operating parameters
DC3 Display channel 3 and 4 operating parameters
DCA Select automatic DC term calculation for lowpass
DCCTN Resume internal buffer data collection
DCCTN? Output internal buffer data collection resume/suspend status
DCHLD Suspend internal buffer data collection
DCMRK Inserts the mark value into the internal buffer
DCO Select open for DC term for lowpass
DCOFF Turn internal buffer data collection mode off
37XXXC GPIB QRG 11
ALPHABETICAL LISTING
Command Description
DCP Display calibration parameters 1st page
DCP1 Display calibration parameters 1st page
DCP2 Display calibration parameters 2nd page
DCPCUR? Outputs the current point count in the collect buffer
DCPMAX? Outputs the maximum number of points that can be collected in the collect buffer
DCS Select short for DC term for lowpass
DCV Enter value for DC term for lowpass
DCV? Output lowpass DC term value
DCX? Output lowpass DC term selection
DCZ Select line impedance for DC term for lowpass
DD0 Turn data drawing off
DD1 Turn data drawing on
DD1? Output data drawing on/off status
DDX? Output active channel domain parameter frequency distance or time
DE1 Select unity as denominator for parameter being defined
DEG Suffix sets phase data type
DEL Delete a file from disk
DEN? Output denominator selection for parameter being defined
DF1 Display 1.0 mm female connector information
DF2 Display 2.4mm female connector information
DF3 Display GPC-3.5 female connector information
DF716 Display 7/16 female connector information
DFC Select discrete frequency calibration data points
DFD Done specifying discrete frequency ranges
DFK Display K female connector information
DFN Display N female connector information
DFN75 Display N Female 75-Ohm connector information
DFP Display Front panel instrument state
DFQ Enter single discrete frequency
DFS Display SMA female connector information
DFSP Display Special Female connector information
DFT Display TNC female connector information
DFV Display V female connector information
DG7 Display GPC-7 Male connector information
DGS Display GPIB status information
DGT Display 1st CRT test pattern
DGT1 Display 1st CRT test pattern
DGT2 Display 2nd CRT test pattern
DGT3 Display 3rd CRT test pattern
12 37XXXC GPIB QRG
ALPHABETICAL LISTING
Command Description
DIA Select air as active dielectric
DIE Enter a dielectric value
DIM Select microporous teflon as active dielectric
DIP Select polyethylene as active dielectric
DIR Output a directory listing to the GPIB
DIS Display active segmented limit
DIS? Output active segmented limit on/off status
DISKRD Output disk file data to the GPIB
DISKWR Write GPIB data to a disk file
DIT Select Teflon as active dielectric
DIV Select division as trace math for active channel
DIX? Output dielectric constant
DLA Select group delay display for active channel
DLP Select distance lowpass mode for active channel
DM1 Display 1.0 mm male connector information
DM2 Display 2.4mm male connector information
DM3 Display GPC-3.5 male connector information
DM716 Display 7/16 male connector information
DMK Display K male connector information
DMN Display N male connector information
DMN75 Display N Male 75-Ohm connector information
DMS Display SMA male connector information
DMSP Display Special Male connector information
DMT Display TNC male connector information
DMV Display V male connector information
DNM Display data normalized to trace memory on active channel
DOASF Display band A special female connector offset-short information
DOASM Display band A special male connector offset-short information
DOBSF Display band B special female connector offset-short information
DOBSM Display band B special male connector offset-short information
DOCSF Display band C special female connector offset-short information
DOCSM Display band C special male connector offset-short information
DOF1 Display 1.0 mm female connector offset-short information
DOM1 Display 1.0 mm male connector offset-short information
DPI Select distance phasor impulse mode for active channel
DPN Enter pen number for data
DPN? Output pen number for data
DPR0 Visible data only OFD format
DPR1 Data pair always OFD format
37XXXC GPIB QRG 13
ALPHABETICAL LISTING
Command Description
DPRX? Output data pair mode visible only or pair always
DR1 Select Marker 1 as Delta Reference Marker
DR2 Select Marker 2 as Delta Reference Marker
DR3 Select Marker 3 as Delta Reference Marker
DR4 Select Marker 4 as Delta Reference Marker
DR5 Select Marker 5 as Delta Reference Marker
DR6 Select Marker 6 as Delta Reference Marker
DRF Turn delta reference mode on
DRL Diagnostic read latch
DRO Turn delta reference mode off
DRO? Output delta reference mode on/off status
DRX? Output delta reference marker number
DSF0 Disable filter shape factor calculation
DSF1 Enable filter shape factor calculation
DSFX? Output filter shape factor calculation enable/disable status
DSP Select single channel display
DSP? Output channel display mode
DSPS21 Select Gain Compression bottom graph displays S21
DSPS21? Output Gain Compression bottom graph selection Normalized/S2
DSQ0 Disable filter Q calculation
DSQ1 Enable filter Q calculation
DSQX? Output filter Q calculation enable/disable status
DTM Display measurement data and trace memory on active channel
DVM Enter DVM channel number
DWG Display waveguide parameters
DWL Diagnostic write latch
E12 Set Millimeter Wave band to E band (WR-12)
E12E Set Millimeter Wave band to E band (WR-12)
EANAIN Measure External Analog In on active channel
ECW Select CW operation for component being edited
ED1 Edit source 1 equation
ED2 Edit source 2 equation
EDG End diagnostics mode
EDR Edit receiver equation
EDV Enter divisor value for equation being edited
EDV? Output divisor value for equation being edited
EKT Select external keyboard testing
EML Enter multiplier value for equation being edited
EML? Output multiplier value for equation being edited
14 37XXXC GPIB QRG
ALPHABETICAL LISTING
Command Description
EOS Enter offset frequency for equation being edited
EOS? Output offset frequency for equation being edited
ESW Select sweep operation for component being edited
EX1RF0 Turn external source 1 rf off
EX1RF1 Turn external source 1 rf on
EX2RF0 Turn external source 2 rf off
EX2RF1 Turn external source 2 rf on
EXD Display external A/D input
EXISTD? Output directory existence information
EXISTF? Output file existence information
EXW? Output multiple source sweep flag for equation being edited
F08 Set Millimeter Wave Band to F Band (WR-8)
FCW0 Turn fast CW measurement mode off
FCW1 Turn fast CW measurement mode on
FCW2 Turn Fast CW mode 2 on
FCWX? Output fast CW measurement mode on/off status
FDE0 Disable Output Data End Message
FDE1 Enable Output Data End Message
FDEX? Output Output Data End Message enable/disable status
FDH0 Select variable length arbitrary block headers
FDH1 Select fixed length arbitrary block headers
FDH2 Select zero length arbitrary block headers
FDHX? Output arbitrary block header length selection
FFD Send form feed to printer and stop print/plot
FGT Select frequency with time gate for active channel
FHI Set data points to 1601
FIL Fill defined discrete frequency range
FLC Source frequency linearity internal calibration
FLO Set data points to 101
FLTBW? Output filter bandwidth
FLTC? Output filter center frequency
FLTL? Output filter loss at reference value
FLTQ? Output filter Q
FLTS? Output filter shape factor
FMA Select ASCII data transfer format
FMB Select IEEE754 64 bit data transfer format
FMC Select IEEE754 32 bit data transfer format
FME Set data points to 401
FMKR Select filter parameters marker mode
37XXXC GPIB QRG 15
ALPHABETICAL LISTING
Command Description
FMT0 Select normal ascii data element delimiting
FMT1 Select enhanced ascii data element delimiting
FMTX? Output ascii data element delimiting mode
FMX? Output data output mode FMA FMB or FMC
FOF Blank frequency information
FON Display frequency information
FOX? Output frequency information on/off status
FP0 Turn flat power correction off
FP1 Turn flat power correction on
FPT Select front panel keypad testing
FPX? Output flat power correction on/off status
FQD Select frequency domain for active channel
FRC Clear all defined discrete frequency ranges
FRI Enter Discrete Fill increment frequency
FRP Enter Discrete Fill number of points
FRS Enter Discrete Fill start frequency
GCMP Enter gain compression point search value
GCMP? Output gain compression point search value
GCT Enter gate center value distance or time
GCT? Output gate center value
GDS Gate symbols displayed on active channel
GHZ Suffix sets frequency data type and scales by 1E9
GLS Select low sidelobe gate shape
GMS Select minimum sidelobe gate shape
GNM Select nominal gate shape
GOF Turn off gating on active channel
GOF? Output gating mode on active channel
GON Turn on gating on active channel
GPN Enter pen number for graticule
GPN? Output pen number for graticule
GRF? Output graph type for active channel
GRT Select Rectangular gate shape
GRTCOL Enter the color number for the graticule
GRTCOL? Output the color number for the graticule
GSN Enter gate span value distance or time
GSN? Output gate span value
GSP Enter gate stop value distance or time
GSP? Output gate stop value
GST Enter gate start value distance or time
16 37XXXC GPIB QRG
ALPHABETICAL LISTING
Command Description
GST? Output gate start value
GSX? Output gate shape
HC0 Disable internal IF calibration
HC1 Enable internal IF calibration and trigger an IF calibration
HCT Trigger an IF calibration
HCX? Output internal IF calibration enable/disable status
HD0 Turn off tabular data headers and page formatting
HD1 Turn on tabular data headers and page formatting
HID Hide active segmented limit
HIST0 Turns off GPIB history writing to disk
HIST1 Turns on GPIB history writing to disk
HISTX? Outputs the history writes to hard disk enable/disable status
HLD Put sweep into hold mode
HLD? Output the sweep hold status
HLDX? Output hold mode (continue, restart, or single sweep)
HPN Enter pen number for header
HPN? Output pen number for header
HZ Suffix sets frequency data type
IACCHAR Input AutoCal characterization data from the GPIB
IARF Enter adapter removal data from GPIB and calibrate
IC1 Enter calibration coefficient 1
IC10 Enter calibration coefficient 10
IC11 Enter calibration coefficient 11
IC12 Enter calibration coefficient 12
IC2 Input Calibration Coefficient 2
IC3 Enter calibration coefficient 3
IC4 Enter calibration coefficient 4
IC5 Enter calibration coefficient 5
IC6 Enter calibration coefficient 6
IC7 Enter calibration coefficient 7
IC8 Enter calibration coefficient 8
IC9 Enter calibration coefficient 9
ICA Enter calibration coefficient 10
ICB Enter calibration coefficient 11
ICC Enter calibration coefficient 12
ICD Enter corrected data for active channel parameter
ICF Enter front panel setup and calibration data
ICL Enter all applicable calibration coefficients for cal type
IEM Enter extended status byte mask
37XXXC GPIB QRG 17
ALPHABETICAL LISTING
Command Description
IF1 Select 10 Hz IF bandwidth
IF2 Select 100 Hz IF bandwidth
IF3 Select 1 KHz IF bandwidth
IF4 Select 10 KHz IF bandwidth
IFA Select 30 KHz IF bandwidth
IFB Select 1st IF bandpass testing
IFD Enter final data for active channel parameter
IFM Select 10 Hz IF bandwidth
IFN Select 1 KHz IF bandwidth
IFP Enter current front panel setup
IFPC Enter flat power coefficients
IFR Select 100 Hz IF bandwidth
IFV Enter frequency values
IFX? Output IF bandwidth
IHDW Enter hardware cal data from GPIB
IKIT Enter calkit data from GPIB
ILM Enter limits status byte mask
IMCF Enter merge calibration files from GPIB and combine
IMG Select imaginary display for active channel
IMU Suffix sets imaginary data type
IND Input Normalization data
INRM Enter normalization data from GPIB
INT Initialize (format) floppy disk
INVER Activate color configuration Inverse
IODF Enter the optical file data from GPIB and calibrate
IPM Enter the 488.2 Service Request Enable mask
IPSC Enter power sweep linearity calibration coefficients
IS1 Enter front panel setup 1
IS10 Enter front panel setup 10
IS2 Enter front panel setup 2
IS3 Enter front panel setup 3
IS4 Enter front panel setup 4
IS5 Enter front panel setup 5
IS6 Enter front panel setup 6
IS7 Enter front panel setup 7
IS8 Enter front panel setup 8
IS9 Enter front panel setup 9
ISC Enter scale and select inverted compressed Smith Chart display
ISE Enter scale and select inverted expanded Smith Chart display
18 37XXXC GPIB QRG
ALPHABETICAL LISTING
Command Description
ISF Exclude isolation
ISM Select normal inverted Smith Chart for active channel
ISN Include isolation
KEC Keep existing calibration data
KHZ Suffix sets frequency data type and scales by 1E3
L1C Perform LO1 internal calibration
L2C Perform LO2 internal calibration
LA1 Select a1 = Ra as phase lock for parameter being defined
LA2 Select a2 = Rb as phase lock for parameter being defined
LAND Select landscape mode for output plot
LAX? Output phase lock selection for parameter being defined
LAYCOL Enter the color number for overlay data
LAYCOL? Output the color number for overlay data
LB0 Turn limits testing beep on failure off
LB1 Turn limits testing beep on failure on
LBX? Output limits testing beeper enable status
LCM Select LRL calibration method
LDARF Load adapter removal files from disk and calibrate
LDMCF Load merge calibration files from disk and combine
LDODF Load optical data files from disk and calibrate
LDT0 Disable printing date/time
LDT1 Enable printing date/time
LFD Enter limit frequency readout delta value
LFD2 Enter limit frequency readout delta value for bottom graph
LFD2? Output limit frequency readout delta value for bottom graph
LFD? Output limit frequency readout delta value
LFP Select limit frequency readout for phase displays
LFR Select limit frequency readout for active channel
LID Enter string for DUT identity
LID? Output string for DUT identity
LIN Select linear magnitude display for active channel
LKS0 Disable lock search mode
LKS1 Enable lock search mode
LKT Load calibration kit information from floppy disk
LL1 Enter length of line 1 for LRL calibration
LL2 Enter length of line 2 for LRL calibration
LL3 Enter length of line 3 for LRL calibration
LLM? Output limit line display mode single or segmented
LLO Enter lower limit value for top graph on active channel
37XXXC GPIB QRG 19
ALPHABETICAL LISTING
Command Description
LLO2 Enter lower limit value for bottom graph on active channel
LLO2? Output lower limit value for bottom graph on active channel
LLO? Output lower limit value for top graph on active channel
LLZ Enter line impedance for LRL calibration
LM2 Select a match for the second device during a LRM type calibration
LM3 Select a match for the third device during a LRM type calibration
LMS Enter string for DUT model/serial number
LMS? Output string for DUT model/serial number
LMZ Enter match impedance for LRM calibration
LMZ? Output match impedance for LRM calibration
LMZL Enter match inductance for LRM calibration
LMZL? Output match inductance for LRM calibration
LNM Enter string for operator name
LNM? Output string for operator name
LO11 Select LO1 phase lock voltage testing
LO12 Select LO1 D/A voltage testing
LO21 Select LO2 main phase lock voltage testing
LO22 Select LO2 offset phase lock voltage testing
LO23 Select LO2 DDS phase lock voltage testing
LO24 Select LO2 main D/A voltage testing
LO25 Select LO2 offset D/A voltage testing
LOC Enter string for operator comment
LOC? Output string for operator comment
LOF Limits display off
LOGO0 Turn hard copy logo off
LOGO1 Turn hard copy logo on
LOGO? Output hard copy logo selection standard/user defined
LOGOS Select standard hard copy logo
LOGOU Select user defined hard copy logo
LOGOX? Output hard copy logo on/off status
LOL0 Turn lower limit off
LOL1 Turn lower limit on at current value
LOL20 Turn lower limit off for bottom graph
LOL21 Turn lower limit on at current value for bottom graph
LOL2X? Output lower limit on/off status for bottom graph
LOLX? Output lower limit on/off status
LON Limits display on
LON? Output limits display on/off status
LPF1? Output limit test failure status on channel 1
20 37XXXC GPIB QRG
ALPHABETICAL LISTING
Command Description
LPF2? Output limit test failure status on channel 2
LPF3? Output limit test failure status on channel 3
LPF4? Output limit test failure status on channel 4
LPF? Output limit test failure status all channels
LPH Select linear magnitude and phase display for active channel
LPI Select lowpass impulse response for active channel
LPS Select lowpass step response for active channel
LPSX? Output lowpass response for active channel impulse or step
LR2 Specify 2 line LRL calibration
LR3 Specify 3 line LRL calibration
LS1 Set lower segmented limit 100 as the active segment
LS10 Select lower segmented limit 10 as the active segment
LS2 Select lower segmented limit 2 as the active segment
LS3 Select lower segmented limit 3 as the active segment
LS4 Select lower segmented limit 4 as the active segment
LS5 Select lower segmented limit 5 as the active segment
LS6 Select lower segmented limit 6 as the active segment
LS7 Select lower segmented limit 7 as the active segment
LS8 Select lower segmented limit 8 as the active segment
LS9 Select lower segmented limit 9 as the active segment
LSB Select least significant byte first binary transfer
LSEG Select segmented limit line display mode
LSNG Select single limit line display mode
LSX? Output active segmented limit
LT0 Turn limits testing off
LT1 Turn limits testing on
LT1? Output limits testing enable status
LTC Select coaxial transmission line for calibration
LTRD Output response data from the dedicated GPIB bus
LTST Display the limits testing menu
LTU Select microstrip transmission line for calibration
LTW Select waveguide transmission line for calibration
LTWRT Send program data to the dedicated GPIB bus
LTX? Output line type
LUP Enter upper limit value for top graph on active channel
LUP2 Enter upper limit value for bottom graph on active channel
LUP2? Output upper limit value for bottom graph on active channel
LUP? Output upper limit value for top graph on active channel
LVH Select high as limits testing TTL level
37XXXC GPIB QRG 21
ALPHABETICAL LISTING
Command Description
LVL Select low as limits testing TTL level
LVX? Output limits testing ttl level status
M Suffix sets distance data type
M1C Set CW mode at marker 1 frequency
M1E Set sweep/zoom end to marker 1 frequency distance or time
M1S Set sweep/zoom start to marker 1 frequency distance or time
M2C Set CW mode at marker 2 frequency
M2E Set sweep/zoom end to marker 2 frequency distance or time
M2S Set sweep/zoom start to marker 2 frequency distance or time
M3C Set CW mode at marker 3 frequency
M3E Set sweep/zoom end to marker 3 frequency distance or time
M3S Set sweep/zoom start to marker 3 frequency distance or time
M4C Set CW mode at marker 4 frequency
M4E Set sweep/zoom end to marker 4 frequency distance or time
M4S Set sweep/zoom start to marker 4 frequency distance or time
M5C Set CW mode at marker 5 frequency
M5E Set sweep/zoom end to marker 5 frequency distance or time
M5S Set sweep/zoom start to marker 5 frequency distance or time
M6C Set CW mode at marker 6 frequency
M6E Set sweep/zoom end to marker 6 frequency distance or time
M6S Set sweep/zoom start to marker 6 frequency distance or time
MAG Select log magnitude display for active channel
MAT Select matched reflective devices during cal
MD Create a new disk directory
MEASDLY Set Measurement Delay time
MEASDLY0 Disable Measurement Delay
MEASDLY1 Enable Measurement Delay
MEASDLY? Output Measurement Delay time
MEASDLYX? Output Measurement Delay on/off status
MEM Display trace memory on active channel
MFGCT Start multiple frequency swept power gain compression test
MHZ Suffix sets frequency data type and scales by 1E6
MIN Select subtraction as trace math for active channel
MIX Select mixed reflective devices during calibration
MK1 Enter marker 1 frequency distance or time and turn on
MK1? Output marker 1 frequency distance or time
MK2 Enter marker 2 frequency distance or time and turn on
MK2? Output marker 2 frequency distance or time
MK3 Enter marker 3 frequency distance or time and turn on
22 37XXXC GPIB QRG
ALPHABETICAL LISTING
Command Description
MK3? Output marker 3 frequency distance or time
MK4 Enter marker 4 frequency distance or time and turn on
MK4? Output marker 4 frequency distance or time
MK5 Enter marker 5 frequency distance or time and turn on
MK5? Output marker 5 frequency distance or time
MK6 Enter marker 6 frequency distance or time and turn on
MK6? Output marker 6 frequency distance or time
MKRC Select interpolated marker functionality
MKRCOL Enter the color number for the markers
MKRCOL? Output the color number for the markers
MKRD Select discrete marker functionality
MKRX? Output interpolated/discrete marker functionality
MKSL Marker search left
MKSR Marker search right
MKT0 Turn marker tracking off
MKT1 Turn marker tracking on
MKTX? Output marker tracking on/off status
MM Suffix sets distance data type and scales by 1E-3
MMBX? Output Millimeter Wave band selection
MMN Move active marker to minimum trace value
MMT Suffix sets distance data type and scales by 1E-3
MMX Move active marker to maximum trace value
MNUCOL Enter the color number for the menu headers
MNUCOL? Output the color number for the menu headers
MO1 Turn off marker 1
MO2 Turn off marker 2
MO3 Turn off marker 3
MO4 Turn off marker 4
MO5 Turn off marker 5
MO6 Turn off marker 6
MOF Turn marker display off
MON Turn marker display on
MON? Output marker display on/off status
MOSET Enter constant offset log magnitude for active channel
MOSET? Output constant offset log magnitude for active channel
MPH Select log magnitude and phase display for active channel
MPN Enter pen number for markers and limits
MPN? Output pen number for markers and limits
MR1 Turn marker 1 on and make it the active marker
37XXXC GPIB QRG 23
ALPHABETICAL LISTING
Command Description
MR1? Output marker 1 on/off status
MR2 Turn marker 2 on and make it the active marker
MR2? Output marker 2 on/off status
MR3 Turn marker 3 on and make it the active marker
MR3? Output marker 3 on/off status
MR4 Turn marker 4 on and make it the active marker
MR4? Output marker 4 on/off status
MR5 Turn marker 5 on and make it the active marker
MR5? Output marker 5 on/off status
MR6 Turn marker 6 on and make it the active marker
MR6? Output marker 6 on/off status
MRM Display the Marker Readout menu
MRR Restore original marker range
MRX? Output active marker number
MS Suffix sets time data type and scales by 1E-3
MS0 Turn multiple source mode off
MS1 Turn multiple source mode on
MSB Select most significant byte first binary transfer
MSD Select multiple source define mode
MSFH Enter high loss value for shape factor calculation
MSFH? Output high loss value for shape factor calculation
MSFL Enter low loss value for shape factor calculation
MSFL? Output low loss value for shape factor calculation
MSR0 Select 0 as reference for marker search and bandwidth calculation
MSRD Select delta reference marker as reference for marker search and bandwidth calculation
MSRM Select maximum as reference for marker search and bandwidth calculation
MSRX? Output reference selection for marker search and bandwidth calculation
MSX? Output multiple source mode on/off/define
MTH? Output trace math math type
MTR Suffix sets distance data type
MUL Select multiplication as trace math for active channel
MV Suffix sets voltage data type and scales by 1E-3
NA1 Select a1 as numerator for parameter being defined
NA2 Select a2 as numerator for parameter being defined
NB1 Select b1 as numerator for parameter being defined
NB2 Select b2 as numerator for parameter being defined
NCS Go to next calibration step
NEWCO Activate color configuration New
NMKR Select normal markers on active channel marker mode
24 37XXXC GPIB QRG
ALPHABETICAL LISTING
Command Description
NOC Select normal calibration data points
NOFST Enter nominal offset value for external gain
NOFST? Output nominal offset value for external gain
NP101 Set data points to 101
NP1601 Set data points to 1601
NP201 Set data points to 201
NP401 Set data points to 401
NP51 Set data points to 51
NP801 Set data points to 801
NRD Display non-ratioed parameters on 4 channels
NRMS Normalize S21 for gain compression testing
NRMS21 Select Gain Compression bottom graph displays Normalized S21
NS Suffix sets time data type and scales by 1E-9
NSC Suffix sets time data type and scales by 1E-9
NU1 Select unity as numerator for parameter being defined
NUM? Output numerator selection for parameter being defined
O3CM Select Triple Offset Short calibration method
O4FD Output final data for all 4 channels to the GPIB
O4SC Output corrected data for all four S-parameters
O4SR Output raw data for all four S-parameters
OACCHAR Output AutoCal characterization data to the GPIB
OACSER Output auto-cal box serial number
OACTYPE Output auto-cal box type
OAM1 Output channel 1 active marker value
OAM2 Output channel 2 active marker value
OAM3 Output channel 3 active marker value
OAM4 Output channel 4 active marker value
OBMP Output the display as a bitmap
OC1 Output calibration coefficients 1
OC10 Output calibration coefficients 10
OC11 Output calibration coefficients 11
OC12 Output calibration coefficients 12
OC2 Output calibration coefficients 2
OC3 Output calibration coefficients 3
OC4 Output calibration coefficients 4
OC5 Output calibration coefficients 5
OC6 Output calibration coefficients 6
OC7 Output calibration coefficients 7
OC8 Output calibration coefficients 8
37XXXC GPIB QRG 25
ALPHABETICAL LISTING
Command Description
OC9 Output calibration coefficients 9
OCA Output calibration coefficient A
OCB Output calibration coefficient B
OCC Output calibration coefficient C
OCD Output corrected data for active channel parameter
OCF Output front panel setup and calibration data
OCL Output all applicable calibration coefficients for cal type
OCM Select offset short calibration method
OCS Output internal buffer collected data
ODAT Output hard copy tabular data to GPIB
ODR Output directory listing of the floppy drive
ODRH Output directory listing of the hard drive
ODV Output distance values for time domain
OEB Output extended status byte
OEL Output error list
OEM Output extended status byte mask
OFD Output final data for active channel parameter
OFD1 Output final data for channel 1 parameter
OFD2 Output final data for channel 2 parameter
OFD3 Output final data for channel 3 parameter
OFD4 Output final data for channel 4 parameter
OFF Enter offset value for top graph of active channel
OFF2 Enter offset value for bottom graph of active channel
OFF2? Output offset value for bottom graph of active channel
OFF? Output offset value for top graph of active channel
OFP Output current front panel setup
OFPC Output flat power coefficients
OFV Output frequency values
OGCFD Output gain compression final data to GPIB
OGCFV Output gain compression frequency values to GPIB
OGCTXT Output text format gain compression data to GPIB
OGE Output extended description of current GPIB error
OGL Output extended description of previous GPIB error
OHDR Output hard copy header information to GPIB
OHDW Output hardware cal data to GPIB
OHGL Output HPGL format data to GPIB
OHM Suffix sets impedance data type
OID Output instrument identification string
OLB Output limits status byte
26 37XXXC GPIB QRG
Command Description
OLM Output limits status byte mask
OM1 Output marker 1 value
OM2 Output marker 2 value
OM3 Output marker 3 value
OM4 Output marker 4 value
OM5 Output marker 5 value
OM6 Output marker 6 value
ONCP Output number of points for current calibration
ONCT Output number of cal terms for current calibration
OND Output Normalization data
ONDF Output number of discrete frequencies
ONE Output number of lines in the error list
ONP Output number of points currently being measured
ONPV Output the number of power sweep power values
ONRM Output stored normalization data to GPIB
OPB Output the 488.2 Status Byte value (same as *STB?)
OPSC Output power sweep linearity calibration coefficients
OPSV Output power sweep power values
ORD Output raw data for active channel parameter
OS1 Output front panel setup number 1
OS10 Output front panel setup number 10
OS11C Output corrected S11 data
OS11R Output raw S11 data
OS12C Output corrected S12 data
OS12R Output raw S12 data
OS2 Output front panel setup number 2
OS21C Output corrected S21 data
OS21R Output raw S21 data
OS22C Output corrected S22 data
OS22R Output raw S22 data
OS2P Output S2P format data to GPIB
OS3 Output front panel setup number 3
OS4 Output front panel setup number 4
OS5 Output front panel setup number 5
OS6 Output front panel setup number 6
OS7 Output front panel setup number 7
OS8 Output front panel setup number 8
OS9 Output front panel setup number 9
OSL Output service log
ALPHABETICAL LISTING
37XXXC GPIB QRG 27
ALPHABETICAL LISTING
Command Description
OTV Output time values for time domain
OTXT Output text format data to GPIB
P1C Select port 1 for connector specification
P1C? Output port 1 connector type
P1MMA Set Port 1 Millimeter Wave Head to Amplified (3742)
P1MMN Set Port 1 Millimeter Wave Head to None
P1MMR Set Port 1 Millimeter Wave Head to Receiver (3741)
P1MMT Set Port 1 Millimeter Wave Head to Transmit/Receiver (3740)
P1MMX? Output Port 1 Millimeter Wave Head type
P1P? Output approximate power level at port 1
P2ALC Perform Port 2 ALC loop internal calibration
P2C Select port 2 for connector specification
P2C? Output port 2 connector type
P2MMA Set Port 2 Millimeter Wave Head to Amplified (3742)
P2MMN Set Port 2 Millimeter Wave Head to none
P2MMR Set Port 2 Millimeter Wave Head to Receiver (3741)
P2MMT Set Port 2 Millimeter Wave Head to Transmit/Receiver (3740)
P2MMX? Output Port 2 Millimeter Wave Head type
PBL Select 1/4 size plot bottom left corner
PBR Select 1/4 size plot bottom right corner
PCP Select measurement phase polar chart mode
PCS Select sweep position polar chart mode
PCX? Output polar chart mode
PDR Print directory listing of the floppy drive
PDRH Print directory listing of the hard drive
PEL Print the error list
PFL Select full-size plot
PFS Print full screen image
PFSC Configure for printing entire screen graphic image
PGR Print graph area screen image
PGRC Configure for printing data area graphic image
PGT Plot graticule
PGTC Configure for plotting graticule
PHA Select phase display for active channel
PHO Enter phase offset for display channel
PHO? Output phase offset for display channel
PLD Plot data area only
PLDC Configure for plotting data area
PLG Select log polar display for active channel
28 37XXXC GPIB QRG
ALPHABETICAL LISTING
Command Description
PLH Plot header
PLHC Configure for plotting header
PLM Plot markers and limits
PLMC Configure for plotting markers and limits
PLO? Output plot mode portrait or landscape
PLR Select linear polar display for active channel
PLS Plot entire screen
PLSC Configure for plotting entire screen
PLT Plot data traces only
PLTC Configure for plotting data traces
PMK Print tabular data for Markers
PMKC Configure for printing tabular data for markers
PMN Plot menu
PMNC Configure for plotting menu
PMT Print tabular data for traces and markers
PMTC Configure for printing tabular data for traces and markers
PORT Select portrait mode for output plot
POSET Enter constant offset phase for active channel
POSET? Output constant offset phase for active channel
POW Select power out display for active channel
PRT? Perform printer test and output status
PS Suffix sets time data type and scales by 1E02
PSC Suffix sets time data type and scales by 1E02
PSCNFRQ? Output the power sweep linearity cal number of frequency poi
PSCNPWR? Output the power sweep linearity cal number of power points
PSCSTEP? Output the power sweep linearity cal power step size
PSL Print the service log
PSP Enter number of power sweeps for flat power correction (obsolete)
PSP? Output number of power sweeps for flat power correction (obsolete)
PSPWR Enter power sweep off power level
PSPWR? Output power sweep off power level
PST Stop print/plot
PSTEP Enter power sweep step size
PSTEP? Output power sweep step size
PSTOP Enter power sweep stop power
PSTOP? Output power sweep stop power
PSTRT Enter power sweep start power
PSTRT? Output power sweep start power
PSWC Perform power sweep linearity calibration
37XXXC GPIB QRG 29
ALPHABETICAL LISTING
Command Description
PSWC0 Turn power sweep linearity calibration off
PSWC1 Turn power sweep linearity calibration on
PSWCX? Output power sweep linearity calibration on/off status
PSWP0 Turn power sweep off
PSWP1 Turn power sweep on
PSWPX? Output power sweep on/off status
PT0 Set tabular printout points skipped to 0
PT1 Set tabular printout points skipped to 1
PT2 Set tabular printout points skipped to 2
PT3 Set tabular printout points skipped to 3
PT4 Set tabular printout points skipped to 4
PT5 Set tabular printout points skipped to 5
PT6 Set tabular printout points skipped to 6
PT7 Set tabular printout points skipped to 7
PT8 Set tabular printout points skipped to 8
PT9 Set tabular printout points skipped to 9
PTAVG Set averaging type to point-by-point averaging
PTB Print tabular data for Traces
PTBC Configure for printing tabular data for traces
PTL Select 1/4 size plot top left corner
PTP Enter the target power for flat power correction
PTP? Output the target power for flat power correction
PTR Select 1/4 size plot top right corner
PTS Enter number of points to be skipped during flat power correction
PTS? Output number of points to be skipped during flat power correction
PW1 Enter external source 1 power level
PW1? Output external source 1 power level
PW2 Enter external source power level
PW2? Output external source power level
PWR Enter internal source power level
PWR? Output internal source power level
Q22 Set Millimeter Wave Band to Q Band (WR-22)
RAD Suffix sets phase data type and scales by 180/pi
RC1 Recall front panel setup number 1 from memory
RC10 Recall front panel setup number 10 from memory
RC2 Recall front panel setup number 2 from memory
RC3 Recall front panel setup number 3 from memory
RC4 Recall front panel setup number 4 from memory
RC5 Recall front panel setup number 5 from memory
30 37XXXC GPIB QRG
ALPHABETICAL LISTING
Command Description
RC6 Recall front panel setup number 6 from memory
RC7 Recall front panel setup number 7 from memory
RC8 Recall front panel setup number 8 from memory
RC9 Recall front panel setup number 9 from memory
RD Remove a disk directory
RDA Select automatic reference delay calculation
RDD Enter reference delay in distance for active channel
RDD? Output reference delay in distance for active channel
RDT Enter reference delay in time for active channel
RDT? Output reference delay in time for active channel
RECALL Recall a data file from disk to a task
REF Enter reference line for top graph of active channel
REF2 Enter reference line for bottom graph of active channel
REF2? Output reference line for bottom graph of active channel
REF? Output reference line for top graph of active channel
REL Select real display for active channel
REU Suffix sets real data type
RGZ Select reflective device greater than Z0
RH0 Select RF off in hold mode
RH1 Select RF on in hold
RHX? Output RF on/off during hold status
RIM Select real and imaginary display for active channel
RLZ Select reflective device less than Z0
RM1 Select reference plane at line 1 midpoint
ROL Enter reflective device offset length
RPC Repeat previous calibration
RPO Enter rear panel dc voltage value
RPO? Output rear panel dc voltage value
RRP Select reference plane at reflection plane
RST Instrument reset (same as *RST)
RST0 Reset instrument front panel memories and reserved parameters
RST1 Reset instrument and front panel memories
RSTAVG Reset the sweep-by-sweep averaging sweep count
RSTCOL Reset color configuration to default
RSTGC Reset gain compression parameters to default
RT0 Turn retrace rf off
RT1 Turn retrace rf on
RTL Return to local
RTX? Output retrace rf on/off status
37XXXC GPIB QRG 31
ALPHABETICAL LISTING
Command Description
RV0 Turn rear panel output voltage off
RV1 Turn rear panel output voltage on
RV1? Output rear panel output voltage on/off status
RVD Set rear panel output mode to dc value
RVH Set rear panel output mode to horizontal
RVL Set rear panel output mode to lock direction
RVV Set rear panel output mode to vertical
RVX? Output rear panel output mode
S Suffix sets time data type
S11 Measure S11 on active channel
S12 Measure S12 on active channel
S21 Measure S21 on active channel
S22 Measure S22 on active channel
SA1 Enter port 1 source attenuator value
SA1? Output port 1 source attenuator value
SA1MAX? Output port 1 source attenuator max value
SAMP2 Use 2 samplers for measurements
SAMP3 Use 3 samplers for measurements
SAMP? Output the number of samplers used for measurements
SAVE Save a data file to disk
SAVEGC Save text format gain compression data to disk
SBD Enter substrate dielectric for microstrip calibration
SBT Enter substrate thickness for microstrip calibration
SCL Enter Scale Resolution for top graph of active channel
SCL2 Enter Scale Resolution for bottom graph of active channel
SCL2? Output Scale Resolution for bottom graph of active channel
SCL? Output Scale Resolution for top graph of active channel
SCM Select standard calibration method
SDG Start diagnostics mode
SDR Select standard receiver mode
SDR? Output receiver mode
SELBB Select Broadband test set operation
SELINT Select Internal (normal) test set operation
SELMM Select Millimeter Wave test set operation
SELSP Select S-parameter test set operation
SELXX? Output the test set selection MMWave/Internal
SETUP Display setup menu
SFC Perform flat test port calibration
SFGCA Select swept frequency gain compression application
32 37XXXC GPIB QRG
ALPHABETICAL LISTING
Command Description
SFGCT Start swept frequency gain compression test
SH1 Set offset short 1 or 2 offset length for offset short calibration
SH2 Set offset short 1 or 2 offset length for offset short calibration
SL1 Select source lock mode
SLC Clear all segmented limits definitions
SLD Select sliding load for calibration
SLH Enter segmented limits horizontal offset
SLH? Output segmented limits horizontal offset
SLL0 Turn lower segmented limits display off
SLL1 Turn lower segmented limits display on
SLLX? Output lower segmented limits display on/off status
SLT Perform SLT internal calibration
SLU0 Turn upper segmented limits display off
SLU1 Turn upper segmented limits display on
SLUX? Output upper segmented limits display on/off status
SLV Enter segmented limits vertical offset
SLV? Output segmented limits vertical offset
SMC Enter scale and select compressed Smith Chart display
SME Enter scale and select expanded Smith Chart display
SMI Select normal Smith Chart for active channel
SMKR Select marker search marker mode
SOF Turn off smoothing
SOF? Output smoothing on/off status
SOFTCO Activate color configuration Soft
SON Enter smoothing value and turn on
SON? Output smoothing value
SPAMPMT Start swept power gain compression AM/PM test
SPAN Enter frequency span
SPAN? Output frequency span
SPD Enter pen speed percentage
SPGCA Select swept power gain compression application
SPGCT Start swept power gain compression test
SPH Enter active segmented limit horizontal stop position
SPH? Output active segmented limit horizontal stop position
SPLN Select normal source lock polarity
SPLR Select reverse source lock polarity
SPLX? Output source lock polarity normal/reverse status
SPR0 Turn spur reduction off
SPR1 Turn spur reduction on
37XXXC GPIB QRG 33
ALPHABETICAL LISTING
Command Description
SPRX? Output spur reduction on/off status
SPTS? Output number of smoothing points
SPV Enter active segmented limit vertical stop position
SPV? Output active segmented limit vertical stop position
SRC1 Select source linearity voltage testing
SRC1? Output external source 1 existence information
SRC1AC Select source 1 as active
SRC1AC? Output source 1 active/inactive status
SRC1ADD Enter external source 1 GPIB address
SRC1ADD? Output external source 1 GPIB address
SRC1EX Select source 1 as external
SRC1EX? Output source 1 external/internal status
SRC1G0 Turn source 1 GPIB control off
SRC1G1 Turn source 1 GPIB control on
SRC1GX? Output source 1 GPIB control on/off status
SRC1MOD? Output external source 1 model/version string
SRC1NA Select source 1 as not active
SRC1NT Select source 1 as internal
SRC2 Select source power voltage testing
SRC2? Output external source 2 existence information
SRC2AC Select source 2 as active
SRC2AC? Output source 2 active/inactive status
SRC2ADD Enter external source 2 GPIB address
SRC2ADD? Output external source 2 GPIB address
SRC2G0 Turn source 2 GPIB control off
SRC2G1 Turn source 2 GPIB control on
SRC2GX? Output source 2 GPIB control on/off status
SRC2MOD? Output external Source 2 model/version string
SRC2NA Select source 2 as not active
SRCH Enter marker search value
SRCH? Output marker search value
SRT Enter start frequency
SRT? Output start frequency
ST1 Select set on mode
STD Store trace to memory on active channel
STH Enter active segmented limit horizontal start position
STH? Output active segmented limit horizontal start position
STOCO Store the current color configuration as Reset
STP Enter stop frequency
34 37XXXC GPIB QRG
ALPHABETICAL LISTING
Command Description
STP? Output stop frequency
STV Enter active segmented limit vertical start position
STV? Output active segmented limit vertical start position
SV1 Save front panel setup number 1 to memory
SV10 Save front panel setup number 10 to memory
SV2 Save front panel setup number 2 to memory
SV3 Save front panel setup number 3 to memory
SV4 Save front panel setup number 4 to memory
SV5 Save front panel setup number 5 to memory
SV6 Save front panel setup number 6 to memory
SV7 Save front panel setup number 7 to memory
SV8 Save front panel setup number 8 to memory
SV9 Save front panel setup number 9 to memory
SVB Save current band definitions
SVBMM Save and activate the new Millimeter Wave band definitions
SWAVG Set averaging type to sweep-by-sweep averaging
SWAVG? Output averaging type (sweep-by-sweep or point-by-point)
SWP Return to normal sweep mode
SWP? Output sweep mode
SWPDIR? Output instantaneous sweep direction forward/reverse
SWR Select SWR display for active channel
SXX? Output s parameter or user defined parameter of active channel
T13 Select overlaid channel 1 and 3 display
T24 Select overlaid channel 2 and 4 display
TA2 Enter port 2 test attenuator value
TA2? Output port 2 test attenuator value
TA2MAX? Output port 2 test attenuator max value
TACD Take AutoCal data
TBP Select time bandpass mode for active channel
TC1 Take calibration data for port 1
TC2 Take calibration data for port 2
TCD Take calibration data on one or both ports as necessary
TCM Select the TRM calibration method
TDC Select time domain harmonic frequency calibration data points
TDDIST Set time domain parameter to distance for active channel
TDDIST? Output active channel time domain parameter distance or time
TDPI0 Turn phasor impulse response off for active channel
TDPI1 Turn phasor impulse response on for active channel
TDPIX? Output phasor impulse on/off status for active channel
37XXXC GPIB QRG 35
ALPHABETICAL LISTING
Command Description
TDTIME Set time domain parameter to time for active channel
TDX? Output domain mode for active channel
TEB Select external trigger and executes *DDT definition
TEX Select external (rear panel) measurement triggering
TIB Select GPIB measurement triggering
TIME Enter the system time
TIME? Output the system time
TIN Select internal measurement triggering
TK1 Select tracking mode
TLP Select time lowpass mode for active channel
TLZ Enter through line impedance for calibration
TOL Enter through offset length for calibration
TPI Select time phasor impulse mode for active channel
TPN Enter pen number for trace overlay data
TPN? Output pen number for trace overlay data
TRCCOL Enter the color number for memory data
TRCCOL? Output the color number for memory data
TRS Trigger/restart sweep
TST Perform self test and output status (same as *TST?)
TXX? Output trigger source internal/external/get/extddt status
U10 Select 10 mil UTF calibration kit
U15 Select 15 mil UTF calibration kit
U25 Select 25 mil UTF calibration kit
UNDOGC Exit gain compression and undo changes
UPL0 Turn upper limit off
UPL1 Turn upper limit on at current value
UPL20 Turn upper limit off for bottom graph
UPL21 Turn upper limit on at current value for bottom graph
UPL2X? Output upper limit on/off status for bottom graph
UPLX? Output upper limit on/off status
US Suffix sets time data type and scales by 1E-6
US1 Select upper segmented limit 1 as the active segment
US10 Select upper segmented limit 10 as the active segment
US2 Select upper segmented limit 2 as the active segment
US3 Select upper segmented limit 3 as the active segment
US4 Select upper segmented limit 4 as the active segment
US5 Select upper segmented limit 5 as the active segment
US6 Select upper segmented limit 6 as the active segment
US7 Select upper segmented limit 7 as the active segment
36 37XXXC GPIB QRG
ALPHABETICAL LISTING
Command Description
US8 Select upper segmented limit 8 as the active segment
US9 Select upper segmented limit 9 as the active segment
USC Suffix sets time data type and scales by 1E-6
USE Enter effective dielectric for microstrip calibration
USL Enter label string for user parameter being defined
USL? Output label string for user parameter being defined
USR1 Measure user parameter 1 on active channel
USR2 Measure user parameter 2 on active channel
USR3 Measure user parameter 3 on active channel
USR4 Measure user parameter 4 on active channel
USW Enter microstrip width for microstrip calibration
USZ Enter microstrip impedance for microstrip calibration
V Suffix sets voltage data type
V15 Set Millimeter Wave Band to V Band (WR-15)
VLT Suffix sets voltage data type
VSP Enter rear panel stop voltage value
VSP? Output rear panel stop voltage value
VST Enter rear panel start voltage value
VST? Output rear panel start voltage value
W10 Set Millimeter Wave Band to W Band (WR-10)
W10E Set Millimeter Wave Band to extended W Band (WR-10E)
WCO Enter waveguide cutoff frequency for user defined kit
WFS Wait full sweep until all display data is valid
WIDE Use entire display width for graphs
WKD Select user defined waveguide calibration kit
WKI Select installed waveguide calibration kit
WLS Select low sidelobe window shape
WMS Select minimum sidelobe window shape
WNM Select nominal window shape
WRT Select rectangular window shape
WSH1 Enter waveguide short offset 1 for user defined kit
WSH2 Enter waveguide short offset 2 for user defined kit
WSH3 Enter waveguide short 3 offset for user defined kit
WSX? Output window shape
XM3 Suffix sets unitless data type and scales by 1E-3
XMKR? Output marker mode
XSB? Output byte order for output data LSB or MSB
XX1 Suffix sets unitless data type
XX3 Suffix sets unitless data type and scales by 1E3
37XXXC GPIB QRG 37
ALPHABETICAL LISTING
Command Description
ZCT Enter zoom range center value time or distance
ZCT? Output zoom range center value
ZSN Enter zoom range span value time or distance
ZSN? Output zoom range span value
ZSP Enter zoom range stop value time or distance
ZSP? Output zoom range stop value
ZST Enter zoom range start value time or distance
ZST? Output zoom range start value
38 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
ADPL Enter electrical length for adapter removal ADAPTER REMOVAL (Ch 9)
ADPL? Output electrical length for adapter removal ADAPTER REMOVAL (Ch 9)
IARF Enter adapter removal data from GPIB and calibrate ADAPTER REMOVAL (Ch 9)
ADDFC Enter frequency counter GPIB address ADDRESSING (Ch 8)
ADDFC? Output frequency counter GPIB address ADDRESSING (Ch 8)
ADDPLT Enter plotter GPIB address ADDRESSING (Ch 8)
ADDPLT? Output plotter GPIB address ADDRESSING (Ch 8)
ADDPM Enter power meter GPIB address ADDRESSING (Ch 8)
ADDPM? Output power meter GPIB address ADDRESSING (Ch 8)
SRC1ADD? Output external source 1 GPIB address ADDRESSING (Ch 8)
ABORTCAL Abort calibration in progress and keep existing calibra
ACAA Set AutoCal standard to assurance AUTOCAL (Ch 5)
ACADPL Enter AutoCal adapter length AUTOCAL (Ch 5)
ACADPL? Output AutoCal adapter length AUTOCAL (Ch 5)
ACADR SetAutoCal type to adapter removal AUTOCAL (Ch 5)
ACAL1R2 Set adapter removal port configuration to ADAPT & L=1
ACAR1L2 Set adapter removal port configuration to ADAPT & R=1
ACARP? Output AutoCal adapter removal port configuration AUTOCAL (Ch 5)
ACDEF Select default AutoCal isolation averaging factor AUTOCAL (Ch 5)
ACF2P? Output AutoCal full 2 port configuration AUTOCAL (Ch 5)
ACF2TC Set AutoCal 2 port thru type to calibrator AUTOCAL (Ch 5)
ACF2TT Set AutoCal 2 port thru type to true thru AUTOCAL (Ch 5)
ACF2TX? Output AutoCal 2 port thru type selection AUTOCAL (Ch 5)
ACHFD Save AutoCal characterization data to floppy disk AUTOCAL (Ch 5)
ACHHD Save AutoCal characterization data to hard disk AUTOCAL (Ch 5)
ACIAF Enter user AutoCal isolation averaging factor AUTOCAL (Ch 5)
ACIAF? Outputuser AutoCal isolation averaging factor AUTOCAL (Ch 5)
ACIAX? Output AutoCal isolation averaging factor omit/de
ACISO Enter AutoCal isolation averaging number AUTOCAL (Ch 5)
ACISO? OutputAutoCal isolation averaging number AUTOCAL (Ch 5)
ACL1AR2 Set adapter removal port configuration to L=1 and
ACL1R2 Set AutoCal full 2 port configuration to L=1 and R=2 AUTOCAL (Ch 5)
ACLO Enter AutoCal load averaging number AUTOCAL (Ch 5)
ACLO? OutputAutoCal load averaging number AUTOCAL (Ch 5)
ACLOAD Set AutoCal standard to load AUTOCAL (Ch 5)
tion data
and R=2
and L=2
-
fault/user selection
ADAPT & R=2
AUTOCAL (Ch 5)
-
AUTOCAL (Ch 5)
AUTOCAL (Ch 5)
AUTOCAL (Ch 5)
AUTOCAL (Ch 5)
37XXXC GPIB QRG 39
FUNCTIONAL LISTING
Command Description Group
ACOMIT Omit using AutoCal isolation averaging factor AUTOCAL (Ch 5)
ACOPEN Set AutoCal standard to open AUTOCAL (Ch 5)
ACP1? Output AutoCal S11 port configuration AUTOCAL (Ch 5)
ACP1L Set AutoCal S11 port configuration to left AUTOCAL (Ch 5)
ACP1R Set AutoCal S11 port configuration to right AUTOCAL (Ch 5)
ACP2? Output AutoCal S22 port configuration AUTOCAL (Ch 5)
ACP2L Set AutoCal S22 port configuration to left AUTOCAL (Ch 5)
ACP2R Set AutoCal S22 port configuration to right AUTOCAL (Ch 5)
ACPL Set AutoCal S11 port configuration to left AUTOCAL (Ch 5)
ACPR Set AutoCal S11 port configuration to right AUTOCAL (Ch 5)
ACR1AL2 Set adapter removal port configuration to R=1 and
ADAPT & L=2
ACR1L2 Set AutoCal full 2 port configuration to R=1 and L=2 AUTOCAL (Ch 5)
ACRFL Enter AutoCal reflection averaging number AUTOCAL (Ch 5)
ACRFL? Output AutoCal reflection averaging number AUTOCAL (Ch 5)
ACS11 Set AutoCal type to S11 AUTOCAL (Ch 5)
ACS22 Set AutoCal type to S22 AUTOCAL (Ch 5)
ACSF2P Set AutoCal type to full 2 port AUTOCAL (Ch 5)
ACSHORT Set AutoCal standard to short AUTOCAL (Ch 5)
ACSTD? Output AutoCal standard AUTOCAL (Ch 5)
ACSW EnterAutoCal switch averaging number AUTOCAL (Ch 5)
ACSW? Output AutoCal switch averaging number AUTOCAL (Ch 5)
ACTHRU Set AutoCal standard to thru AUTOCAL (Ch 5)
ACTU Enter AutoCal thru averaging number AUTOCAL (Ch 5)
ACTU? Output AutoCal thru averaging number AUTOCAL (Ch 5)
ACTUAVG Enter AutoCal thru update averaging number AUTOCAL (Ch 5)
ACTUAVG? Output AutoCal thru update averaging number AUTOCAL (Ch 5)
ACTULS Apply last thru update cal setup AUTOCAL (Ch 5)
ACX? Output AutoCal type AUTOCAL (Ch 5)
BEGAC StartAutoCal AUTOCAL (Ch 5)
BEGCH Start AutoCal characterization AUTOCAL (Ch 5)
BEGTU Start AutoCal thru update AUTOCAL (Ch 5)
IACCHAR Input AutoCal characterization data from the GPIB AUTOCAL (Ch 5)
OACCHAR Output AutoCal characterization data to the GPIB AUTOCAL (Ch 5)
OACSER Output auto-cal box serial number AUTOCAL (Ch 5)
OACTYPE Output auto-cal box type AUTOCAL (Ch 5)
TACD Take AutoCal data AUTOCAL (Ch 5)
A12 Simulate12-term calibration CALIBRATION (Ch 5)
A8R Simulate 1-path 2-port calibration reverse path CALIBRATION (Ch 5)
AUTOCAL (Ch 5)
40 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
A8T Simulate 1-path 2-port calibration forward path CALIBRATION (Ch 5)
ABT Simulate trans freq response calibration forward and re
verse
AFT Simulate transmission frequency response calibration
forward path
ARB Simulate reflection only calibration both ports CALIBRATION (Ch 5)
ARF Simulate reflection only calibration port 1 CALIBRATION (Ch 5)
ARR Simulate reflection only calibration port 2 CALIBRATION (Ch 5)
ART Simulate trans freq response calibration reverse path CALIBRATION (Ch 5)
BBL Select broadband load for calibration CALIBRATION (Ch 5)
BBZ Enter broadband load impedance for calibration CALIBRATION (Ch 5)
BBZL Enter broadband load inductance for calibration CALIBRATION (Ch 5)
BEG Begin taking calibration data CALIBRATION (Ch 5)
BPF Enter break point frequency for 3 line LRL calibration CALIBRATION (Ch 5)
C12 Select 12 term calibration CALIBRATION (Ch 5)
C8R Select 1-path 2-port calibration reverse path CALIBRATION (Ch 5)
C8T Select 1-path 2-port calibration forward path CALIBRATION (Ch 5)
CBT Select trans freq response calibration forward and re-
verse
CC0 Enter capacitance coefficient 0 for open CALIBRATION (Ch 5)
CC1 Enter capacitance coefficient 1 for open CALIBRATION (Ch 5)
CC2 Enter capacitance coefficient 2 for open CALIBRATION (Ch 5)
CC3 Enter capacitance coefficient 3 for open CALIBRATION (Ch 5)
CF1 Select female 1.0 mm connector for current port CALIBRATION (Ch 5)
CF2 Select female 2.4mm connector for current port CALIBRATION (Ch 5)
CF3 Select female GPC-3.5 connector for current port CALIBRATION (Ch 5)
CF716 Selectfemale 7/16 connector for current port CALIBRATION (Ch 5)
CFC Select female TNC connector for current port CALIBRATION (Ch 5)
CFK Select female K connector for current port CALIBRATION (Ch 5)
CFN Select female Type N connector for current port CALIBRATION (Ch 5)
CFN75 Select Female type N 75-ohm connector for current port CALIBRATION (Ch 5)
CFS Select female SMA connector for current port CALIBRATION (Ch 5)
CFSP Select Special Female connector for current port CALIBRATION (Ch 5)
CFSPA Select Band A special female connector for current port CALIBRATION (Ch 5)
CFSPB Select Band B special female connector for current port CALIBRATION (Ch 5)
CFSPC Select Band C special female connector for current port CALIBRATION (Ch 5)
CFT Select trans freq response calibration forward path CALIBRATION (Ch 5)
CFV Select female V connector for current port CALIBRATION (Ch 5)
CL0 Enter inductive coefficient 0 for short CALIBRATION (Ch 5)
CL1 Enter inductive coefficient 1 for short CALIBRATION (Ch 5)
CALIBRATION (Ch 5)
-
CALIBRATION (Ch 5)
CALIBRATION (Ch 5)
37XXXC GPIB QRG 41
FUNCTIONAL LISTING
Command Description Group
CL2 Enter inductive coefficient 2 for short CALIBRATION (Ch 5)
CL3 Enter inductive coefficient 3 for short CALIBRATION (Ch 5)
CM1 Select male 1.0 mm connector for current port CALIBRATION (Ch 5)
CM2 Select male 2.4mm connector for current port CALIBRATION (Ch 5)
CM3 Select male GPC-3.5 connector for current port CALIBRATION (Ch 5)
CM716 Select male 7/16 connector for current port CALIBRATION (Ch 5)
CMC Select male TNC connector for current port CALIBRATION (Ch 5)
CMK Select male K connector for current port CALIBRATION (Ch 5)
CMN Select male N connector for current port CALIBRATION (Ch 5)
CMN75 Select Male type N 75-Ohm connector for current port CALIBRATION (Ch 5)
CMS Select male SMA connector for current port CALIBRATION (Ch 5)
CMSP Select Special Male connector for current port CALIBRATION (Ch 5)
CMSPA Select Band A special male connector for current port CALIBRATION (Ch 5)
CMSPB Select Band B special male connector for current port CALIBRATION (Ch 5)
CMSPC Select Band C special male connector for current port CALIBRATION (Ch 5)
CMV Select male V connector for current port CALIBRATION (Ch 5)
CMX? Output calibration method CALIBRATION (Ch 5)
CND Select user specified connector for current port CALIBRATION (Ch 5)
CNG Select GPC-7 connector for current port CALIBRATION (Ch 5)
COF Turn error correction off CALIBRATION (Ch 5)
CON Turn error correction on CALIBRATION (Ch 5)
CON? Output error correction on/off status CALIBRATION (Ch 5)
COO Enter offset for open for user specified connector (Stan
dard Calibration)
COS Enter offset for short for user specified connector CALIBRATION (Ch 5)
CRB Select reflection only calibration both ports CALIBRATION (Ch 5)
CRF Select reflection only calibration port 1 CALIBRATION (Ch 5)
CRR Select reflection only calibration port 2 CALIBRATION (Ch 5)
CRT Select trans freq response calibration reverse path CALIBRATION (Ch 5)
CSF? Output cal start frequency CALIBRATION (Ch 5)
CTF? Output cal stop frequency CALIBRATION (Ch 5)
CWC Select CW frequency calibration data points CALIBRATION (Ch 5)
CXX? Output calibration type CALIBRATION (Ch 5)
DFC Select discrete frequency calibration data points CALIBRATION (Ch 5)
DFD Done specifying discrete frequency ranges CALIBRATION (Ch 5)
DFQ Enter single discrete frequency CALIBRATION (Ch 5)
OCM Select offset short calibration method CALIBRATION (Ch 5)
IC2 Input Calibration Coefficient 2 CALIBRATION (Ch 5)
IC3 Enter calibration coefficient 3 CALIBRATION (Ch 5)
-
CALIBRATION (Ch 5)
42 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
IC4 Enter calibration coefficient 4 CALIBRATION (Ch 5)
IC5 Enter calibration coefficient 5 CALIBRATION (Ch 5)
IC6 Enter calibration coefficient 6 CALIBRATION (Ch 5)
IC7 Enter calibration coefficient 7 CALIBRATION (Ch 5)
IC8 Enter calibration coefficient 8 CALIBRATION (Ch 5)
IC9 Enter calibration coefficient 9 CALIBRATION (Ch 5)
ICA Enter calibration coefficient 10 CALIBRATION (Ch 5)
ICB Enter calibration coefficient 11 CALIBRATION (Ch 5)
ICC Enter calibration coefficient 12 CALIBRATION (Ch 5)
ICD Enter corrected data for active channel parameter CALIBRATION(Ch 5)
ICF Enter front panel setup and calibration data CALIBRATION (Ch 5)
ICL Enter all applicable calibration coefficients for cal type CALIBRATION (Ch 5)
IFD Enter final data for active channel parameter CALIBRATION (Ch 5)
ISF Exclude isolation CALIBRATION (Ch 5)
ISN Include isolation CALIBRATION (Ch 5)
KEC Keep existing calibration data CALIBRATION (Ch 5)
LCM Select LRL calibration method CALIBRATION (Ch 5)
LL1 Enter length of line 1 for LRL calibration CALIBRATION (Ch 5)
LL2 Enter length of line 2 for LRL calibration CALIBRATION (Ch 5)
LL3 Enter length of line 3 for LRL calibration CALIBRATION (Ch 5)
LLZ Enter line impedance for LRL calibration CALIBRATION (Ch 5)
LM2 Select a match for the second device during a LRM type
calibration
LM3 Select a match for the third device during a LRM type
calibration
LMZ Enter match impedance for LRM calibration CALIBRATION (Ch 5)
LMZ? Output match impedance for LRM calibration CALIBRATION (Ch 5)
LMZL Enter match inductance for LRM calibration CALIBRATION (Ch 5)
LMZL? Output match inductance for LRM calibration CALIBRATION (Ch 5)
LR2 Specify 2 line LRL calibration CALIBRATION (Ch 5)
LR3 Specify 3 line LRL calibration CALIBRATION (Ch 5)
LTC Select coaxial transmission line for calibration CALIBRATION (Ch 5)
LTU Select microstrip transmission line for calibration CALIBRATION (Ch 5)
LTW Select waveguide transmission line for calibration CALIBRATION (Ch 5)
LTX? Output line type CALIBRATION (Ch 5)
MAT Select matched reflective devices during cal CALIBRATION (Ch 5)
MIX Selectmixed reflective devices during calibration CALIBRATION (Ch 5)
NCS Go to next calibration step CALIBRATION (Ch 5)
NOC Select normal calibration data points CALIBRATION (Ch 5)
CALIBRATION (Ch 5)
CALIBRATION (Ch 5)
37XXXC GPIB QRG 43
FUNCTIONAL LISTING
Command Description Group
O3CM Select Triple Offset Short calibration method CALIBRATION (Ch 5)
ONCT Outputnumber of cal terms for current calibration CALIBRATION (Ch 5)
P1C Select port 1 for connector specification CALIBRATION (Ch 5)
P1C? Output port 1 connector type CALIBRATION (Ch 5)
P1P? Output approximate power level at port 1 CALIBRATION (Ch 5)
P2C Select port 2 for connector specification CALIBRATION (Ch 5)
P2C? Output port 2 connector type CALIBRATION (Ch 5)
PSP Enter number of power sweeps for flat power correction
(obsolete)
PSP? Output number of power sweeps for flat power correction
(obsolete)
PTS Enter number of points to be skipped during flat power
correction
PTS? Output number of points to be skipped during flat power
correction
RGZ Select reflective device greater than Z0 CALIBRATION (Ch 5)
RLZ Select reflective device less than Z0 CALIBRATION (Ch 5)
RM1 Select reference plane at line 1 midpoint CALIBRATION (Ch 5)
ROL Enter reflective device offset length CALIBRATION (Ch 5)
RPC Repeat previous calibration CALIBRATION (Ch 5)
RRP Select reference plane at reflection plane CALIBRATION (Ch 5)
SBD Enter substrate dielectric for microstrip calibration CALIBRATION (Ch 5)
SBT Enter substrate thickness for microstrip calibration CALIBRATION (Ch 5)
SCM Select standard calibration method CALIBRATION (Ch 5)
SFC Perform flat test port calibration CALIBRATION (Ch 5)
SH1 Set offset short 1 or 2 offset length for offset short cali
bration
SH2 Set offset short 1 or 2 offset length for offset short cali
bration
SLD Select sliding load for calibration CALIBRATION (Ch 5)
TC1 Take calibration data for port 1 CALIBRATION (Ch 5)
TC2 Take calibration data for port 2 CALIBRATION (Ch 5)
TCD Take calibration data on one or both ports as necessary CALIBRATION (Ch 5)
TCM Select the TRM calibration method CALIBRATION (Ch 5)
TDC Select time domain harmonic frequency calibration data
points
TLZ Enterthrough line impedance for calibration CALIBRATION (Ch 5)
TOL Enter through offset length for calibration CALIBRATION (Ch 5)
U10 Select 10 mil UTF calibration kit CALIBRATION (Ch 5)
U15 Select 15 mil UTF calibration kit CALIBRATION (Ch 5)
U25 Select 25 mil UTF calibration kit CALIBRATION (Ch 5)
CALIBRATION (Ch 5)
CALIBRATION (Ch 5)
CALIBRATION (Ch 5)
CALIBRATION (Ch 5)
-
CALIBRATION (Ch 5)
-
CALIBRATION (Ch 5)
CALIBRATION (Ch 5)
44 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
USE Enter effective dielectric for microstrip calibration CALIBRATION (Ch 5)
USW Enter microstrip width for microstrip calibration CALIBRATION (Ch 5)
USZ Enter microstrip impedance for microstrip calibration CALIBRATION (Ch 5)
WCO Enter waveguide cutoff frequency for user defined kit CALIBRATION (Ch 5)
WKD Select user defined waveguide calibration kit CALIBRATION (Ch 5)
WKI Select installed waveguide calibration kit CALIBRATION (Ch 5)
WSH1 Enter waveguide short offset 1 for user defined kit CALIBRATION (Ch 5)
WSH2 Enter waveguide short offset 2 for user defined kit CALIBRATION (Ch 5)
WSH3 Enter waveguide short 3 offset for user defined kit CALIBRATION (Ch 5)
CH1 Make channel 1 the active channel CHANNELS (Ch 4)
CH2 Make channel 2 the active channel CHANNELS (Ch 4)
CH3 Make channel 3 the active channel CHANNELS (Ch 4)
CH4 Make channel 4 the active channel CHANNELS (Ch 4)
CHX? Output active channel number CHANNELS (Ch 4)
D13 Display channels1&3 CHANNELS (Ch 4)
D14 Display all four channels CHANNELS (Ch 4)
D24 Select dual channel display with channels2&4 CHANNELS (Ch 4)
DSP Select single channel display CHANNELS (Ch 4)
DSP? Output channel display mode CHANNELS (Ch 4)
T13 Select overlaid channel 1 and 3 display CHANNELS (Ch 4)
T24 Select overlaid channel 2 and 4 display CHANNELS (Ch 4)
CM Suffix sets distance data type and scales by 1E-2 DATA ENTRY SUFFIXES (Ch 4)
CMT Suffix sets distance data type and scales by 1E-2 DATA ENTRY SUFFIXES (Ch 4)
DB Suffixsets power data type DATA ENTRY SUFFIXES (Ch 4)
DBL Suffix sets power data type DATA ENTRY SUFFIXES (Ch 4)
DBM Suffix sets power data type DATA ENTRY SUFFIXES (Ch 4)
DEG Suffix sets phase data type DATA ENTRY SUFFIXES (Ch 4)
RAD Suffix sets phase data type and scales by 180/pi DATA ENTRY SUFFIXES (Ch 4)
GHZ Suffix sets frequency data type and scales by 1E9 DATA ENTRY SUFFIXES (Ch 4)
HZ Suffix sets frequency data type DATA ENTRY SUFFIXES (Ch 4)
IMU Suffix sets imaginary data type DATA ENTRY SUFFIXES (Ch 4)
KHZ Suffix sets frequency data type and scales by 1E3 DATA ENTRY SUFFIXES (Ch 4)
M Suffix sets distance data type DATA ENTRY SUFFIXES (Ch 4)
MHZ Suffix sets frequency data type and scales by 1E6 DATA ENTRY SUFFIXES (Ch 4)
MM Suffix sets distance data type and scales by 1E-3 DATA ENTRY SUFFIXES (Ch 4)
MMT Suffix sets distance data type and scales by 1E-3 DATA ENTRY SUFFIXES (Ch 4)
MS Suffix sets time data type and scales by 1E-3 DATA ENTRY SUFFIXES (Ch 4)
MTR Suffix sets distance data type DATA ENTRY SUFFIXES (Ch 4)
MV Suffix sets voltage data type and scales by 1E-3 DATA ENTRY SUFFIXES (Ch 4)
37XXXC GPIB QRG 45
FUNCTIONAL LISTING
Command Description Group
NS Suffixsets time data type and scales by 1E-9 DATA ENTRY SUFFIXES (Ch 4)
NSC Suffix sets time data type and scales by 1E-9 DATA ENTRY SUFFIXES (Ch 4)
OHM Suffix sets impedance data type DATA ENTRY SUFFIXES (Ch 4)
PS Suffix sets time data type and scales by 1E02 DATA ENTRY SUFFIXES (Ch 4)
PSC Suffix sets time data type and scales by 1E02 DATA ENTRY SUFFIXES (Ch 4)
REU Suffix sets real data type DATA ENTRY SUFFIXES (Ch 4)
S Suffix sets time data type DATA ENTRY SUFFIXES (Ch 4)
US Suffixsets time data type and scales by 1E-6 DATA ENTRY SUFFIXES (Ch 4)
USC Suffix sets time data type and scales by 1E-6 DATA ENTRY SUFFIXES (Ch 4)
V Suffix sets voltage data type DATA ENTRY SUFFIXES (Ch 4)
VLT Suffix sets voltage data type DATA ENTRY SUFFIXES (Ch 4)
XM3 Suffix sets unitless data type and scales by 1E-3 DATA ENTRY SUFFIXES (Ch 4)
XX1 Suffix sets unitless data type DATA ENTRY SUFFIXES (Ch 4)
XX3 Suffix sets unitless data type and scales by 1E3 DATA ENTRY SUFFIXES (Ch 4)
DPR0 Visible data only OFD format DATA TRANSFER (Ch 7)
DPR1 Data pair always OFD format DATA TRANSFER (Ch 7)
FDE0 Disable Output Data End Message DATA TRANSFER (Ch 7)
FDE1 Enable Output Data End Message DATATRANSFER (Ch 7)
FDEX? Output Output Data End Message enable/disable status DATA TRANSFER (Ch 7)
FMA Select ASCII data transfer format DATA TRANSFER (Ch 7)
FMB Select IEEE754 64 bit data transfer format DATA TRANSFER (Ch 7)
FMC Select IEEE754 32 bit data transfer format DATA TRANSFER (Ch 7)
FMX? Output data output mode FMA FMB or FMC DATA TRANSFER (Ch 7)
OCA Output calibration coefficient A DATA TRANSFER (Ch 7)
OCB Output calibration coefficient B DATA TRANSFER (Ch 7)
OCC Output calibration coefficient C DATA TRANSFER (Ch 7)
OCD Output corrected data for active channel parameter DATA TRANSFER (Ch 7)
OCF Output front panel setup and calibration data DATA TRANSFER (Ch 7)
OCL Output all applicable calibration coefficients for cal type DATA TRANSFER (Ch 7)
IC1 Enter calibration coefficient 1 DATA TRANSFER (Ch 7)
IC10 Enter calibration coefficient 10 DATA TRANSFER (Ch 7)
IC11 Enter calibration coefficient 11 DATA TRANSFER (Ch 7)
IC12 Enter calibration coefficient 12 DATA TRANSFER (Ch 7)
IFPC Enter flat power coefficients DATA TRANSFER (Ch 7)
LSB Select least significant byte first binary transfer DATA TRANSFER (Ch 7)
MSB Select most significant byte first binary transfer DATA TRANSFER (Ch 7)
O4FD Output final data for all 4 channels to the GPIB DATA TRANSFER (Ch 7)
O4SC Output corrected data for all four S-parameters DATA TRANSFER (Ch 7)
O4SR Output raw data for all four S-parameters DATA TRANSFER (Ch 7)
46 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
OAM1 Outputchannel 1 active marker value DATA TRANSFER (Ch 7)
OAM2 Outputchannel 2 active marker value DATA TRANSFER (Ch 7)
OAM3 Outputchannel 3 active marker value DATA TRANSFER (Ch 7)
OAM4 Outputchannel 4 active marker value DATA TRANSFER (Ch 7)
OC1 Output calibration coefficients 1 DATA TRANSFER (Ch 7)
OC10 Output calibration coefficients 10 DATA TRANSFER (Ch 7)
OC11 Output calibration coefficients 11 DATA TRANSFER (Ch 7)
OC12 Output calibration coefficients 12 DATA TRANSFER (Ch 7)
OC2 Output calibration coefficients 2 DATA TRANSFER (Ch 7)
OC3 Output calibration coefficients 3 DATA TRANSFER (Ch 7)
OC4 Output calibration coefficients 4 DATA TRANSFER (Ch 7)
OC5 Output calibration coefficients 5 DATA TRANSFER (Ch 7)
OC6 Output calibration coefficients 6 DATA TRANSFER (Ch 7)
OC7 Output calibration coefficients 7 DATA TRANSFER (Ch 7)
OC8 Output calibration coefficients 8 DATA TRANSFER (Ch 7)
OC9 Output calibration coefficients 9 DATA TRANSFER (Ch 7)
ODR Output directory listing of the floppy drive DATA TRANSFER (Ch 7)
ODRH Output directory listing of the hard drive DATA TRANSFER (Ch 7)
ODV Output distance values for time domain DATA TRANSFER (Ch 7)
OEL Output error list DATA TRANSFER (Ch 7)
OFD Output final data for active channel parameter DATA TRANSFER (Ch 7)
OFD1 Output final data for channel 1 parameter DATA TRANSFER (Ch 7)
OFD2 Output final data for channel 2 parameter DATA TRANSFER (Ch 7)
OFD3 Output final data for channel 3 parameter DATA TRANSFER (Ch 7)
OFD4 Output final data for channel 4 parameter DATA TRANSFER (Ch 7)
OFP Output current front panel setup DATA TRANSFER (Ch 7)
OFPC Output flat power coefficients DATA TRANSFER (Ch 7)
OFV Output frequency values DATA TRANSFER (Ch 7)
OGE Output extended description of current GPIB error DATA TRANSFER (Ch 7)
OGL Output extended description of previous GPIB error DATA TRANSFER (Ch 7)
OID Outputinstrument identification string DATA TRANSFER (Ch 7)
OLM Output limits status byte mask DATA TRANSFER (Ch 7)
OM1 Output marker 1 value DATA TRANSFER (Ch 7)
OM2 Output marker 2 value DATA TRANSFER (Ch 7)
OM3 Output marker 3 value DATA TRANSFER (Ch 7)
OM4 Output marker 4 value DATA TRANSFER (Ch 7)
OM5 Output marker 5 value DATA TRANSFER (Ch 7)
OM6 Output marker 6 value DATA TRANSFER (Ch 7)
ONCP Output number of points for current calibration DATA TRANSFER (Ch 7)
37XXXC GPIB QRG 47
FUNCTIONAL LISTING
Command Description Group
OND Output Normalization data DATA TRANSFER (Ch 7)
ONE Output number of lines in the error list DATA TRANSFER (Ch 7)
ORD Output raw data for active channel parameter DATA TRANSFER (Ch 7)
OS1 Output front panel setup number 1 DATA TRANSFER (Ch 7)
OS10 Output front panel setup number 10 DATA TRANSFER (Ch 7)
OS2 Output front panel setup number 2 DATA TRANSFER (Ch 7)
OS3 Output front panel setup number 3 DATA TRANSFER (Ch 7)
OS4 Output front panel setup number 4 DATA TRANSFER (Ch 7)
OS5 Output front panel setup number 5 DATA TRANSFER (Ch 7)
OS6 Output front panel setup number 6 DATA TRANSFER (Ch 7)
OS7 Output front panel setup number 7 DATA TRANSFER (Ch 7)
OS8 Output front panel setup number 8 DATA TRANSFER (Ch 7)
OS9 Output front panel setup number 9 DATA TRANSFER (Ch 7)
OSL Output service log DATA TRANSFER (Ch 7)
XSB? Output byte order for output data LSB or MSB DATA TRANSFER (Ch 7)
ALC Perform ALC loop internal calibration DIAGNOSTICS (Ch 8)
DBP Select distance bandpass mode for active channel DIAGNOSTICS (Ch 8)
DCA Select automatic DC term calculation for lowpass DIAGNOSTICS (Ch 8)
DCO Select open for DC term for lowpass DIAGNOSTICS (Ch 8)
DLP Select distance lowpass mode for active channel DIAGNOSTICS (Ch 8)
DRL Diagnostic read latch DIAGNOSTICS (Ch 8)
DVM Enter DVM channel number DIAGNOSTICS (Ch 8)
DWL Diagnostic write latch DIAGNOSTICS (Ch 8)
EDG End diagnostics mode DIAGNOSTICS (Ch 8)
EXD Display external A/D input DIAGNOSTICS (Ch 8)
FLC Source frequency linearity internal calibration DIAGNOSTICS (Ch 8)
FPX? Output flat power correction on/off status DIAGNOSTICS (Ch 8)
LO25 Select LO2 offset D/A voltage testing DIAGNOSTICS (Ch 8)
IFB Select 1st IF bandpass testing DIAGNOSTICS (Ch 8)
L1C Perform LO1 internal calibration DIAGNOSTICS (Ch 8)
L2C Perform LO2 internal calibration DIAGNOSTICS (Ch 8)
LKS0 Disable lock search mode DIAGNOSTICS (Ch 8)
LKS1 Enable lock search mode DIAGNOSTICS (Ch 8)
LO11 Select LO1 phase lock voltage testing DIAGNOSTICS (Ch 8)
LO12 Select LO1 D/A voltage testing DIAGNOSTICS (Ch 8)
LO21 Select LO2 main phase lock voltage testing DIAGNOSTICS (Ch 8)
LO22 Select LO2 offset phase lock voltage testing DIAGNOSTICS (Ch 8)
LO23 Select LO2 DDS phase lock voltage testing DIAGNOSTICS (Ch 8)
LO24 Select LO2 main D/A voltage testing DIAGNOSTICS (Ch 8)
48 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
NRD Display non-ratioed parameters on 4 channels DIAGNOSTICS (Ch 8)
P2ALC Perform Port 2 ALC loop internal calibration DIAGNOSTICS(Ch 8)
PSL Print the service log DIAGNOSTICS (Ch 8)
SDG Start diagnostics mode DIAGNOSTICS (Ch 8)
SDR Select standard receiver mode DIAGNOSTICS (Ch 8)
SLT Perform SLT internal calibration DIAGNOSTICS (Ch 8)
SRC1 Select source linearity voltage testing DIAGNOSTICS (Ch 8)
ADRIVE Select the floppy drive as the default drive DISK FUNCTION (Ch 8)
CD Change default directory DISK FUNCTION (Ch 8)
CDRIVE Select the hard disk as the default drive DISK FUNCTION (Ch 8)
COPY Copya files contents to another file DISK FUNCTION (Ch 8)
CWD? Output current working directory string DISK FUNCTION (Ch 8)
DEL Delete a file from disk DISK FUNCTION (Ch 8)
DIR Output a directory listing to the GPIB DISK FUNCTION (Ch 8)
DISKRD Output disk file data to the GPIB DISK FUNCTION (Ch 8)
DISKWR Write GPIB data to a disk file DISK FUNCTION (Ch 8)
EXISTD? Output directory existence information DISK FUNCTION (Ch 8)
EXISTF? Output file existence information DISK FUNCTION (Ch 8)
INT Initialize (format) floppy disk DISK FUNCTION (Ch 8)
LDARF Load adapter removal files from disk and calibrate DISK FUNCTION (Ch 8)
LKT Load calibration kit information from floppy disk DISK FUNCTION (Ch 8)
MD Create a new disk directory DISK FUNCTION (Ch 8)
PDR Print directory listing of the floppy drive DISK FUNCTION (Ch 8)
PDRH Printdirectory listing of the hard drive DISK FUNCTION (Ch 8)
PGT Plot graticule DISK FUNCTION (Ch 8)
RD Remove a disk directory DISK FUNCTION (Ch 8)
RECALL Recall a data file from disk to a task DISK FUNCTION (Ch 8)
SAVE Save a data file to disk DISK FUNCTION (Ch 8)
SAVEGC Save text format gain compression data to disk DISK FUNCTION (Ch 8)
ADD Select addition as trace math for active channel DISPLAY (Ch 4)
APR Enter group delay aperture setting on active channel DISPLAY (Ch 4)
APR? Output group delay aperture setting on active channel DISPLAY (Ch 4)
ASC Autoscale the active channel display DISPLAY (Ch 4)
ASP Enter polar stop sweep position angle DISPLAY (Ch 4)
ASP? Output polar stop sweep position angle DISPLAY (Ch 4)
AST Enter polar start sweep position angle DISPLAY (Ch 4)
AST? Output polar start sweep position angle DISPLAY (Ch 4)
DAT Display data only on active channel DISPLAY (Ch 4)
DAT? Output trace memory display mode DISPLAY (Ch 4)
37XXXC GPIB QRG 49
FUNCTIONAL LISTING
Command Description Group
DIA Select air as active dielectric DISPLAY (Ch 4)
DIE Enter a dielectric value DISPLAY (Ch 4)
DIM Select microporous teflon as active dielectric DISPLAY (Ch 4)
DIP Select polyethylene as active dielectric DISPLAY (Ch 4)
DIT Select Teflon as active dielectric DISPLAY (Ch 4)
DIV Select division as trace math for active channel DISPLAY (Ch 4)
DIX? Output dielectric constant DISPLAY (Ch 4)
DLA Select group delay display for active channel DISPLAY (Ch 4)
DNM Display data normalized to trace memory on active chan
nel
DTM Display measurement data and trace memory on active
channel
GRF? Output graph type for active channel DISPLAY (Ch 4)
IMG Select imaginary display for active channel DISPLAY (Ch 4)
ISC Enter scale and select inverted compressed Smith Chart
display
ISE Enter scale and select inverted expanded Smith Chart
display
ISM Selectnormal inverted Smith Chart for active channel DISPLAY (Ch 4)
LIN Select linear magnitude display for active channel DISPLAY (Ch 4)
LPH Select linear magnitude and phase display for active
channel
MAG Select log magnitude display for active channel DISPLAY (Ch 4)
MEM Display trace memory on active channel DISPLAY (Ch 4)
MIN Select subtraction as trace math for active channel DISPLAY (Ch 4)
MOSET Enter constant offset log magnitude for active channel DISPLAY (Ch 4)
MOSET? Output constant offset log magnitude for active channel DISPLAY (Ch 4)
MPH Select log magnitude and phase display for active chan
nel
MTH? Output trace math math type DISPLAY (Ch 4)
MUL Select multiplication as trace math for active channel DISPLAY (Ch 4)
OFF Enter offset value for top graph of active channel DISPLAY (Ch 4)
OFF? Output offset value for top graph of active channel DISPLAY (Ch 4)
OFF2 Enter offset value for bottom graph of active channel DISPLAY (Ch 4)
OFF2? Output offset value for bottom graph of active channel DISPLAY (Ch 4)
PCP Select measurement phase polar chart mode DISPLAY (Ch 4)
PCS Select sweep position polar chart mode DISPLAY (Ch 4)
PCX? Output polar chart mode DISPLAY (Ch 4)
PHA Select phase display for active channel DISPLAY (Ch 4)
PHO Enter phase offset for display channel DISPLAY (Ch 4)
PHO? Output phase offset for display channel DISPLAY (Ch 4)
DISPLAY (Ch 4)
-
DISPLAY (Ch 4)
DISPLAY (Ch 4)
DISPLAY (Ch 4)
DISPLAY (Ch 4)
-
DISPLAY (Ch 4)
50 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
PLG Select log polar display for active channel DISPLAY (Ch 4)
PLR Select linear polar display for active channel DISPLAY (Ch 4)
POSET Enter constant offset phase for active channel DISPLAY (Ch 4)
POSET? Output constant offset phase for active channel DISPLAY (Ch 4)
POW Select power out display for active channel DISPLAY(Ch 4)
RDA Select automatic reference delay calculation DISPLAY (Ch 4)
RDD Enter reference delay in distance for active channel DISPLAY (Ch 4)
RDD? Output reference delay in distance for active channel DISPLAY (Ch 4)
RDT Enter reference delay in time for active channel DISPLAY (Ch 4)
RDT? Output reference delay in time for active channel DISPLAY (Ch 4)
REF Enter reference line for top graph of active channel DISPLAY (Ch 4)
REF? Output reference line for top graph of active channel DISPLAY (Ch 4)
REF2 Enter reference line for bottom graph of active channel DISPLAY (Ch 4)
REF2? Output reference line for bottom graph of active channel DISPLAY (Ch 4)
REL Select real display for active channel DISPLAY (Ch 4)
RIM Select real and imaginary display for active channel DISPLAY (Ch 4)
SCL Enter Scale Resolution for top graph of active channel DISPLAY (Ch 4)
SCL? Output Scale Resolution for top graph of active channel DISPLAY (Ch 4)
SCL2 Enter Scale Resolution for bottom graph of active chan-
nel
SCL2? Output Scale Resolution for bottom graph of active chan-
nel
SETUP Display setup menu DISPLAY (Ch 4)
SMC Enter scale and select compressed Smith Chart display DISPLAY (Ch 4)
SME Enter scale and select expanded Smith Chart display DISPLAY (Ch 4)
SMI Selectnormal Smith Chart for active channel DISPLAY (Ch 4)
STD Store trace to memory on active channel DISPLAY (Ch 4)
SWR Select SWR display for active channel DISPLAY (Ch 4)
AOF Turn averaging off ENHANCEMENT (Ch 4)
AOF? Output averaging on/off status ENHANCEMENT (Ch 4)
AON Turn averaging on ENHANCEMENT (Ch 4)
AVG Enter averaging count and turn on ENHANCEMENT (Ch 4)
AVG? Output averaging count ENHANCEMENT (Ch 4)
IF1 Select 10 Hz IF bandwidth ENHANCEMENT (Ch 4)
IF2 Select 100 Hz IF bandwidth ENHANCEMENT (Ch 4)
IF3 Select 1 KHz IF bandwidth ENHANCEMENT (Ch 4)
IF4 Select 10 KHz IF bandwidth ENHANCEMENT (Ch 4)
IFA Select 30 KHz IF bandwidth ENHANCEMENT (Ch 4)
IFM Select 10 Hz IF bandwidth ENHANCEMENT (Ch 4)
DISPLAY (Ch 4)
DISPLAY (Ch 4)
37XXXC GPIB QRG 51
FUNCTIONAL LISTING
Command Description Group
IFN Select 1 KHz IF bandwidth ENHANCEMENT (Ch 4)
IFR Select 100 Hz IF bandwidth ENHANCEMENT (Ch 4)
IFX? Output IF bandwidth ENHANCEMENT (Ch 4)
MEASDLY Set Measurement Delay time ENHANCEMENT (Ch 4)
MEASDLY? Output Measurement Delay time ENHANCEMENT (Ch 4)
MEASDLY0 Disable Measurement Delay ENHANCEMENT (Ch 4)
MEASDLY1 Enable Measurement Delay ENHANCEMENT (Ch 4)
MEASDLYX? Output Measurement Delay on/off status ENHANCEMENT (Ch 4)
PTAVG Set averaging type to point-by-point averaging ENHANCEMENT (Ch 4)
RSTAVG Reset the sweep-by-sweep averaging sweep count ENHANCEMENT (Ch 4)
SOF Turn off smoothing ENHANCEMENT (Ch 4)
SOF? Output smoothing on/off status ENHANCEMENT (Ch 4)
SON Enter smoothing value and turn on ENHANCEMENT (Ch 4)
SON? Output smoothing value ENHANCEMENT (Ch 4)
SPLN Select normal source lock polarity ENHANCEMENT (Ch 4)
SPLR Select reverse source lock polarity ENHANCEMENT (Ch 4)
SPLX? Output source lock polarity normal/reverse status ENHANCEMENT (Ch 4)
SPR0 Turn spur reduction off ENHANCEMENT (Ch 4)
SPR1 Turn spur reduction on ENHANCEMENT (Ch 4)
SPRX? Output spur reduction on/off status ENHANCEMENT (Ch 4)
SWAVG Set averaging type to sweep-by-sweep averaging ENHANCEMENT (Ch 4)
SWAVG? Output averaging type (sweep-by-sweep or
point-by-point)
FCW0 Turnfast CW measurement mode off FAST CW (Ch 7)
FCW1 Turnfast CW measurement mode on FAST CW (Ch 7)
FCW2 TurnFast CW mode 2 on FAST CW (Ch 7)
FCWX? Outputfast CW measurement mode on/off status FAST CW (Ch 7)
CALR Perform receiver cal for gain compression testing GAIN COMPRESSION (Ch 9)
DSPS21 Select Gain Compression bottom graph displays S21 GAIN COMPRESSION (Ch 9)
DSPS21? Output Gain Compression bottom graph selection Nor
malized/S2
GCMP Entergain compression point search value GAIN COMPRESSION (Ch 9)
GCMP? Output gain compression point search value GAIN COMPRESSION (Ch 9)
IPSC Enter power sweep linearity calibration coefficients GAIN COMPRESSION (Ch 9)
MFGCT Start multiple frequency swept power gain compression
test
NOFST Enter nominal offset value for external gain GAIN COMPRESSION (Ch 9)
NOFST? Output nominal offset value for external gain GAIN COMPRESSION (Ch 9)
NRMS Normalize S21 for gain compression testing GAINCOMPRESSION (Ch 9)
ENHANCEMENT (Ch 4)
-
GAIN COMPRESSION (Ch 9)
GAIN COMPRESSION (Ch 9)
52 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
NRMS21 Select Gain Compression bottom graph displays Normal
OPSC Outputpower sweep linearity calibration coefficients GAIN COMPRESSION (Ch 9)
PSCNFRQ? Output the power sweep linearity cal number of fre
PSCNPWR? Output the power sweep linearity cal number of power
PSCSTEP? Output the power sweep linearity cal power step size GAIN COMPRESSION (Ch 9)
PSPWR Enterpower sweep off power level GAIN COMPRESSION (Ch 9)
PSPWR? Output power sweep off power level GAIN COMPRESSION (Ch 9)
PSTEP Enter power sweep step size GAIN COMPRESSION (Ch 9)
PSTEP? Output power sweep step size GAIN COMPRESSION (Ch 9)
PSTOP Enter power sweep stop power GAIN COMPRESSION (Ch 9)
PSTOP? Output power sweep stop power GAIN COMPRESSION (Ch 9)
PSTRT Enter power sweep start power GAIN COMPRESSION (Ch 9)
PSTRT? Output power sweep start power GAIN COMPRESSION (Ch 9)
PSWC Performpower sweep linearity calibration GAIN COMPRESSION (Ch 9)
PSWC0 Turn power sweep linearity calibration off GAIN COMPRESSION (Ch 9)
PSWC1 Turn power sweep linearity calibration on GAIN COMPRESSION (Ch 9)
PSWCX? Output power sweep linearity calibration on/off status GAIN COMPRESSION (Ch 9)
PSWP0 Turnpower sweep off GAIN COMPRESSION (Ch 9)
PSWP1 Turnpower sweep on GAIN COMPRESSION (Ch 9)
PSWPX? Output power sweep on/off status GAIN COMPRESSION (Ch 9)
RSTGC Resetgain compression parameters to default GAIN COMPRESSION (Ch 9)
SFGCA Select swept frequency gain compression application GAIN COMPRESSION (Ch 9)
SFGCT Start swept frequency gain compression test GAIN COMPRESSION (Ch 9)
SPAMPMT Start swept power gain compression AM/PM test GAIN COMPRESSION (Ch 9)
SPGCA Selectswept power gain compression application GAIN COMPRESSION (Ch 9)
SPGCT Start swept power gain compression test GAIN COMPRESSION (Ch 9)
UNDOGC Exit gain compression and undo changes GAIN COMPRESSION (Ch 9)
BMPB SelectBlack on White as bitmap type HARD COPY (Ch 8)
BMPC Select Color on White as bitmap type HARD COPY (Ch 8)
BMPT Select true color as bitmap type HARD COPY (Ch 8)
DPN Enter pen number for data HARD COPY (Ch 8)
DPN? Output pen number for data HARD COPY (Ch 8)
FFD Send form feed to printer and stop print/plot HARDCOPY (Ch 8)
LOC Enter string for operator comment HARD COPY (Ch 8)
LOC? Output string for operator comment HARD COPY (Ch 8)
LOGO? Output hard copy logo selection standard/user defined HARD COPY (Ch 8)
LOGO0 Turn hard copy logo off HARD COPY (Ch 8)
ized S21
-
quency poi
points
GAIN COMPRESSION (Ch 9)
-
GAIN COMPRESSION (Ch 9)
GAIN COMPRESSION (Ch 9)
37XXXC GPIB QRG 53
FUNCTIONAL LISTING
Command Description Group
LOGO1 Turn hard copy logo on HARDCOPY (Ch 8)
LOGOS Select standard hard copy logo HARD COPY (Ch 8)
LOGOU Select user defined hard copy logo HARD COPY (Ch 8)
LOGOX? Output hard copy logo on/off status HARDCOPY (Ch 8)
ODAT Output hard copy tabular data to GPIB HARD COPY (Ch 8)
GPN Enter pen number for graticule HARD COPY (Ch 8)
GPN? Output pen number for graticule HARD COPY (Ch 8)
HD0 Turn off tabular data headers and page formatting HARD COPY (Ch 8)
HD1 Turn on tabular data headers and page formatting HARD COPY (Ch 8)
HIST0 Turnsoff GPIB history writing to disk HARD COPY (Ch 8)
HIST1 Turnson GPIB history writing to disk HARD COPY (Ch 8)
HISTX? Outputsthe history writes to hard disk enable/disable
status
HPN Enter pen number for header HARD COPY (Ch 8)
HPN? Output pen number for header HARD COPY (Ch 8)
LAND Select landscape mode for output plot HARD COPY (Ch 8)
LDT0 Disable printing date/time HARD COPY (Ch 8)
LDT1 Enable printing date/time HARD COPY (Ch 8)
LMS Enter string for DUT model/serial number HARD COPY (Ch 8)
LMS? Output string for DUT model/serial number HARD COPY (Ch 8)
LNM Enter string for operator name HARD COPY (Ch 8)
LNM? Output string for operator name HARD COPY (Ch 8)
MPN Enter pen number for markers and limits HARD COPY (Ch 8)
MPN? Output pen number for markers and limits HARD COPY (Ch 8)
OBMP Output the display as a bitmap HARD COPY (Ch 8)
OGCTXT Output text format gain compression data to GPIB HARD COPY (Ch 8)
OHDR Output hard copy header information to GPIB HARD COPY (Ch 8)
OHGL OutputHPGL format data to GPIB HARDCOPY (Ch 8)
OS2P Output S2P format data to GPIB HARD COPY (Ch 8)
OTXT Output text format data to GPIB HARD COPY (Ch 8)
PBL Select 1/4 size plot bottom left corner HARD COPY (Ch 8)
PBR Select 1/4 size plot bottom right corner HARD COPY (Ch 8)
PFL Select full-size plot HARD COPY (Ch 8)
PFS Print full screen image HARD COPY (Ch 8)
PFSC Configure for printing entire screen graphic image HARD COPY (Ch 8)
PGR Print graph area screen image HARD COPY (Ch 8)
PGRC Configure for printing data area graphic image HARD COPY (Ch 8)
PGTC Configure for plotting graticule HARD COPY (Ch 8)
PLD Plot data area only HARD COPY (Ch 8)
HARD COPY (Ch 8)
54 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
PLDC Configure for plotting data area HARD COPY (Ch 8)
PLH Plot header HARD COPY (Ch 8)
PLHC Configure for plotting header HARD COPY (Ch 8)
PLM Plot markers and limits HARD COPY (Ch 8)
PLMC Configure for plotting markers and limits HARD COPY (Ch 8)
PLO? Output plot mode portrait or landscape HARD COPY (Ch 8)
PLS Plot entire screen HARD COPY (Ch 8)
PLSC Configure for plotting entire screen HARD COPY (Ch 8)
PLT Plot data traces only HARD COPY (Ch 8)
PLTC Configure for plotting data traces HARD COPY (Ch 8)
PMK Print tabular data for Markers HARD COPY (Ch 8)
PMKC Configure for printing tabular data for markers HARD COPY (Ch 8)
PMN Plot menu HARD COPY (Ch 8)
PMNC Configure for plotting menu HARD COPY (Ch 8)
PMT Print tabular data for traces and markers HARD COPY (Ch 8)
PMTC Configurefor printing tabular data for traces and markers HARD COPY (Ch 8)
PORT Select portrait mode for output plot HARD COPY (Ch 8)
PST Stop print/plot HARD COPY (Ch 8)
PT0 Set tabular printout points skipped to 0 HARD COPY (Ch 8)
PT1 Set tabular printout points skipped to 1 HARD COPY (Ch 8)
PT2 Set tabular printout points skipped to 2 HARD COPY (Ch 8)
PT3 Set tabular printout points skipped to 3 HARD COPY (Ch 8)
PT4 Set tabular printout points skipped to 4 HARD COPY (Ch 8)
PT5 Set tabular printout points skipped to 5 HARD COPY (Ch 8)
PT6 Set tabular printout points skipped to 6 HARD COPY (Ch 8)
PT7 Set tabular printout points skipped to 7 HARD COPY (Ch 8)
PT8 Set tabular printout points skipped to 8 HARD COPY (Ch 8)
PT9 Set tabular printout points skipped to 9 HARD COPY (Ch 8)
PTB Print tabular data for Traces HARD COPY (Ch 8)
PTBC Configure for printing tabular data for traces HARDCOPY (Ch 8)
PTL Select 1/4 size plot top left corner HARD COPY (Ch 8)
PTR Select 1/4 size plot top right corner HARD COPY (Ch 8)
SPD Enter pen speed percentage HARD COPY (Ch 8)
TPN Enter pen number for trace overlay data HARD COPY (Ch 8)
TPN? Output pen number for trace overlay data HARD COPY (Ch 8)
*CLS Clear status bytes and structures IEEE 488.2 (Ch 7)
*DDT Enter the 488.2 Define Device Trigger command string IEEE 488.2 (Ch 7)
*DDT? Outputthe 488.2 Define Device Trigger command string IEEE 488.2 (Ch 7)
*ESE Enter the 488.2 Standard Event Status Enable mask IEEE 488.2 (Ch 7)
37XXXC GPIB QRG 55
FUNCTIONAL LISTING
Command Description Group
*ESE? Output the 488.2 Standard Event Status Enable mask IEEE 488.2 (Ch 7)
*ESR? Outputthe 488.2 Standard Event Status Register value IEEE 488.2 (Ch 7)
*IDN? Output the 488.2 instrument identification string IEEE 488.2 (Ch 7)
*IST? Output the value of the ist message IEEE 488.2 (Ch 7)
*OPC Initiate the 488.2 Operation Complete sequence IEEE488.2 (Ch 7)
*OPC? Initiate the 488.2 Operation Complete Query sequence IEEE 488.2 (Ch 7)
*PRE Enter the 488.2 Parallel Poll Register Enable mask IEEE 488.2 (Ch 7)
*PRE? Outputthe 488.2 Parallel Poll Register Enable mask IEEE 488.2 (Ch 7)
*RST Instrument reset IEEE 488.2 (Ch 7)
*SRE Enter the 488.2 Service Request Enable mask IEEE 488.2 (Ch 7)
*SRE? Outputthe 488.2 Service Request Enable mask IEEE 488.2 (Ch 7)
*STB? Output the 488.2 Status Byte value IEEE 488.2 (Ch 7)
*TRG Initiate a Group Execute Trigger sequence IEEE 488.2 (Ch 7)
*TST? Performself test and output status IEEE 488.2 (Ch 7)
*WAI Wait to continue IEEE 488.2 (Ch 7)
OPB Output the 488.2 Status Byte value (same as *STB?) IEEE 488.2 (Ch 7)
TST Perform self test and output status (same as *TST?) IEEE 488.2 (Ch 7)
CCD Collect corrected data in an internal buffer INT. BUFFER DATA COLL. (Ch 7)
CFD Collect final data in an internal buffer INT. BUFFER DATA COLL. (Ch 7)
CRD Collect raw data in an internal buffer INT. BUFFER DATA COLL. (Ch 7)
CXD? Output internal buffer data collection mode INT. BUFFER DATA COLL. (Ch 7)
DCCTN Resumeinternal buffer data collection INT. BUFFER DATA COLL. (Ch 7)
DCCTN? Output internal buffer data collection resume/suspend
status
DCHLD Suspend internal buffer data collection INT. BUFFER DATA COLL. (Ch 7)
DCMRK Insertsthe mark value into the internal buffer INT. BUFFER DATA COLL. (Ch 7)
DCOFF Turn internal buffer data collection mode off INT. BUFFER DATA COLL. (Ch 7)
DCPCUR? Outputs the current point count in the collect buffer INT. BUFFER DATA COLL. (Ch 7)
DCPMAX? Outputs the maximum number of points that can be col
lected in the collect buffer
OCS Output internal buffer collected data INT. BUFFER DATA COLL. (Ch 7)
ATTN Attach next segment and make the active segment LIMITS(Ch 6)
BEGN Beginnext segment and make it the active segment LIMITS (Ch 6)
CAS Clear active segmented limit vertical/horizontal defini
tions
DIS Display active segmented limit LIMITS (Ch 6)
DIS? Output active segmented limit on/off status LIMITS (Ch 6)
LOF Limits display off LIMITS (Ch 6)
LOL0 Turn lower limit off LIMITS (Ch 6)
LOL1 Turn lower limit on at current value LIMITS (Ch 6)
INT. BUFFER DATA COLL. (Ch 7)
-
INT. BUFFER DATA COLL. (Ch 7)
-
LIMITS (Ch 6)
56 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
LOL20 Turnlower limit off for bottom graph LIMITS (Ch 6)
LOL21 Turnlower limit on at current value for bottom graph LIMITS (Ch 6)
LOL2X? Outputlower limit on/off status for bottom graph LIMITS (Ch 6)
LOLX? Output lower limit on/off status LIMITS (Ch 6)
STV Enter active segmented limit vertical start position LIMITS (Ch 6)
STV? Output active segmented limit vertical start position LIMITS (Ch 6)
HID Hide active segmented limit LIMITS (Ch 6)
LB0 Turnlimits testing beep on failure off LIMITS (Ch 6)
LB1 Turnlimits testing beep on failure on LIMITS (Ch 6)
LBX? Output limits testing beeper enable status LIMITS (Ch 6)
LFD Enter limit frequency readout delta value LIMITS (Ch 6)
LFD? Output limit frequency readout delta value LIMITS (Ch 6)
LFD2 Enter limit frequency readout delta value for bottom
graph
LFD2? Outputlimit frequency readout delta value for bottom
graph
LFP Select limit frequency readout for phase displays LIMITS (Ch 6)
LFR Select limit frequency readout for active channel LIMITS (Ch 6)
LLM? Output limit line display mode single or segmented LIMITS (Ch 6)
LLO Enter lower limit value for top graph on active channel LIMITS (Ch 6)
LLO? Output lower limit value for top graph on active channel LIMITS (Ch 6)
LLO2 Enter lower limit value for bottom graph on active chan-
nel
LLO2? Outputlower limit value for bottom graph on active chan
nel
LON Limits display on LIMITS (Ch 6)
LON? Output limits display on/off status LIMITS (Ch 6)
LPF? Output limit test failure status all channels LIMITS (Ch 6)
LPF1? Output limit test failure status on channel 1 LIMITS (Ch 6)
LPF2? Output limit test failure status on channel 2 LIMITS (Ch 6)
LPF3? Output limit test failure status on channel 3 LIMITS (Ch 6)
LPF4? Output limit test failure status on channel 4 LIMITS (Ch 6)
LS1 Setlower segmented limit 100 as the active segment LIMITS (Ch 6)
LS10 Select lower segmented limit 10 as the active segment LIMITS (Ch 6)
LS2 Selectlower segmented limit 2 as the active segment LIMITS (Ch 6)
LS3 Selectlower segmented limit 3 as the active segment LIMITS (Ch 6)
LS4 Selectlower segmented limit 4 as the active segment LIMITS (Ch 6)
LS5 Selectlower segmented limit 5 as the active segment LIMITS (Ch 6)
LS6 Selectlower segmented limit 6 as the active segment LIMITS (Ch 6)
LS7 Selectlower segmented limit 7 as the active segment LIMITS (Ch 6)
LIMITS (Ch 6)
LIMITS (Ch 6)
LIMITS (Ch 6)
-
LIMITS (Ch 6)
37XXXC GPIB QRG 57
FUNCTIONAL LISTING
Command Description Group
LS8 Selectlower segmented limit 8 as the active segment LIMITS (Ch 6)
LS9 Selectlower segmented limit 9 as the active segment LIMITS (Ch 6)
LSEG Select segmented limit line display mode LIMITS (Ch 6)
LSNG Select single limit line display mode LIMITS (Ch 6)
LSX? Output active segmented limit LIMITS (Ch 6)
LT0 Turn limits testing off LIMITS (Ch 6)
LT1 Turn limits testing on LIMITS (Ch 6)
LT1? Output limits testing enable status LIMITS (Ch 6)
LTST Display the limits testing menu LIMITS (Ch 6)
LUP Enter upper limit value for top graph on active channel LIMITS (Ch 6)
LUP? Output upper limit value for top graph on active channel LIMITS (Ch 6)
LUP2 Enter upper limit value for bottom graph on active chan
nel
LUP2? Output upper limit value for bottom graph on active chan
nel
LVH Select high as limits testing TTL level LIMITS (Ch 6)
LVL Selectlow as limits testing TTL level LIMITS (Ch 6)
LVX? Output limits testing ttl level status LIMITS (Ch 6)
SLC Clear all segmented limits definitions LIMITS (Ch 6)
SLH Enter segmented limits horizontal offset LIMITS (Ch 6)
SLH? Output segmented limits horizontal offset LIMITS (Ch 6)
SLL0 Turn lower segmented limits display off LIMITS (Ch 6)
SLL1 Turn lower segmented limits display on LIMITS (Ch 6)
SLLX? Outputlower segmented limits display on/off status LIMITS (Ch 6)
SLU0 Turn upper segmented limits display off LIMITS (Ch 6)
SLU1 Turn upper segmented limits display on LIMITS (Ch 6)
SLV Enter segmented limits vertical offset LIMITS (Ch 6)
SLV? Output segmented limits vertical offset LIMITS (Ch 6)
SPH Enter active segmented limit horizontal stop position LIMITS (Ch 6)
SPH? Output active segmented limit horizontal stop position LIMITS (Ch 6)
SPV Enter active segmented limit vertical stop position LIMITS (Ch 6)
SPV? Output active segmented limit vertical stop position LIMITS(Ch 6)
STH Enter active segmented limit horizontal start position LIMITS (Ch 6)
STH? Output active segmented limit horizontal start position LIMITS (Ch 6)
UPL0 Turn upper limit off LIMITS (Ch 6)
UPL1 Turn upper limit on at current value LIMITS (Ch 6)
UPL20 Turn upper limit off for bottom graph LIMITS (Ch 6)
UPL21 Turn upper limit on at current value for bottom graph LIMITS (Ch 6)
UPL2X? Output upper limit on/off status for bottom graph LIMITS (Ch 6)
LIMITS (Ch 6)
-
LIMITS (Ch 6)
-
58 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
UPLX? Output upper limit on/off status LIMITS (Ch 6)
US1 Select upper segmented limit 1 as the active segment LIMITS (Ch 6)
US10 Select upper segmented limit 10 as the active segment LIMITS (Ch 6)
US2 Select upper segmented limit 2 as the active segment LIMITS (Ch 6)
US3 Select upper segmented limit 3 as the active segment LIMITS (Ch 6)
US4 Select upper segmented limit 4 as the active segment LIMITS (Ch 6)
US5 Select upper segmented limit 5 as the active segment LIMITS (Ch 6)
US6 Select upper segmented limit 6 as the active segment LIMITS (Ch 6)
US7 Select upper segmented limit 7 as the active segment LIMITS (Ch 6)
US8 Select upper segmented limit 8 as the active segment LIMITS (Ch 6)
US9 Select upper segmented limit 9 as the active segment LIMITS (Ch 6)
SLUX? Output upper segmented limits display on/off status LMITS (Ch 7)
AMKR Select active marker on all channels marker mode MARKERS (Ch 6)
BWL3 Set bandwidth loss value to 3 dB MARKERS (Ch 6)
BWLS Enterbandwidth loss value MARKERS (Ch 6)
BWLS? Output bandwidth loss value MARKERS (Ch 6)
DR1 Select Marker 1 as Delta Reference Marker MARKERS (Ch 6)
DR2 Select Marker 2 as Delta Reference Marker MARKERS (Ch 6)
DR3 Select Marker 3 as Delta Reference Marker MARKERS (Ch 6)
DR4 Select Marker 4 as Delta Reference Marker MARKERS (Ch 6)
DR5 Select Marker 5 as Delta Reference Marker MARKERS (Ch 6)
DR6 Select Marker 6 as Delta Reference Marker MARKERS (Ch 6)
DRF Turn delta reference mode on MARKERS (Ch 6)
DRO Turn delta reference mode off MARKERS (Ch 6)
DRO? Output delta reference mode on/off status MARKERS (Ch 6)
DRX? Output delta reference marker number MARKERS (Ch 6)
DSF0 Disable filter shape factor calculation MARKERS (Ch 6)
DSF1 Enable filter shape factor calculation MARKERS (Ch 6)
DSFX? Output filter shape factor calculation enable/disable sta
tus
DSQ0 Disable filter Q calculation MARKERS (Ch 6)
DSQ1 Enable filter Q calculation MARKERS (Ch 6)
DSQX? Output filter Q calculation enable/disable status MARKERS (Ch 6)
FLTBW? Output filter bandwidth MARKERS (Ch 6)
FLTC? Output filter center frequency MARKERS (Ch 6)
FLTL? Output filter loss at reference value MARKERS (Ch 6)
FLTQ? Output filter Q MARKERS (Ch 6)
FLTS? Outputfilter shape factor MARKERS (Ch 6)
FMKR Selectfilter parameters marker mode MARKERS (Ch 6)
-
MARKERS (Ch 6)
37XXXC GPIB QRG 59
FUNCTIONAL LISTING
Command Description Group
M1C Set CW mode at marker 1 frequency MARKERS (Ch 6)
M1E Set sweep/zoom end to marker 1 frequency distance or
time
M1S Set sweep/zoom start to marker 1 frequency distance or
time
M2C Set CW mode at marker 2 frequency MARKERS (Ch 6)
M2E Set sweep/zoom end to marker 2 frequency distance or
time
M2S Set sweep/zoom start to marker 2 frequency distance or
time
M3C Set CW mode at marker 3 frequency MARKERS (Ch 6)
M3E Set sweep/zoom end to marker 3 frequency distance or
time
M3S Set sweep/zoom start to marker 3 frequency distance or
time
M4C Set CW mode at marker 4 frequency MARKERS (Ch 6)
M4E Set sweep/zoom end to marker 4 frequency distance or
time
M4S Set sweep/zoom start to marker 4 frequency distance or
time
M5C Set CW mode at marker 5 frequency MARKERS (Ch 6)
M5E Set sweep/zoom end to marker 5 frequency distance or
time
M5S Set sweep/zoom start to marker 5 frequency distance or
time
M6C Set CW mode at marker 6 frequency MARKERS (Ch 6)
M6E Set sweep/zoom end to marker 6 frequency distance or
time
M6S Set sweep/zoom start to marker 6 frequency distance or
time
MK1 Enter marker 1 frequency distance or time and turn on MARKERS (Ch 6)
MK1? Output marker 1 frequency distance or time MARKERS (Ch 6)
MK2 Enter marker 2 frequency distance or time and turn on MARKERS (Ch 6)
MK2? Output marker 2 frequency distance or time MARKERS (Ch 6)
MK3 Enter marker 3 frequency distance or time and turn on MARKERS (Ch 6)
MK3? Output marker 3 frequency distance or time MARKERS (Ch 6)
MK4 Enter marker 4 frequency distance or time and turn on MARKERS (Ch 6)
MK4? Output marker 4 frequency distance or time MARKERS (Ch 6)
MK5 Enter marker 5 frequency distance or time and turn on MARKERS (Ch 6)
MK5? Output marker 5 frequency distance or time MARKERS (Ch 6)
MK6 Enter marker 6 frequency distance or time and turn on MARKERS (Ch 6)
MK6? Output marker 6 frequency distance or time MARKERS (Ch 6)
MKRC Select interpolated marker functionality MARKERS (Ch 6)
MARKERS (Ch 6)
MARKERS (Ch 6)
MARKERS (Ch 6)
MARKERS (Ch 6)
MARKERS (Ch 6)
MARKERS (Ch 6)
MARKERS (Ch 6)
MARKERS (Ch 6)
MARKERS (Ch 6)
MARKERS (Ch 6)
MARKERS (Ch 6)
MARKERS (Ch 6)
60 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
MKRD Select discrete marker functionality MARKERS (Ch 6)
MKRX? Output interpolated/discrete marker functionality MARKERS (Ch 6)
MKSL Marker search left MARKERS (Ch 6)
MKSR Marker search right MARKERS (Ch 6)
MKT0 Turn marker tracking off MARKERS (Ch 6)
MKT1 Turn marker tracking on MARKERS (Ch 6)
MKTX? Output marker tracking on/off status MARKERS (Ch 6)
MMN Move active marker to minimum trace value MARKERS (Ch 6)
MMX Move active marker to maximum trace value MARKERS (Ch 6)
MO1 Turn off marker 1 MARKERS (Ch 6)
MO2 Turn off marker 2 MARKERS (Ch 6)
MO3 Turn off marker 3 MARKERS (Ch 6)
MO4 Turn off marker 4 MARKERS (Ch 6)
MO5 Turn off marker 5 MARKERS (Ch 6)
MO6 Turn off marker 6 MARKERS (Ch 6)
MOF Turn marker display off MARKERS (Ch 6)
MON Turn marker display on MARKERS (Ch 6)
MON? Output marker display on/off status MARKERS (Ch 6)
MR1 Turn marker 1 on and make it the active marker MARKERS (Ch 6)
MR1? Output marker 1 on/off status MARKERS (Ch 6)
MR2 Turn marker 2 on and make it the active marker MARKERS (Ch 6)
MR2? Output marker 2 on/off status MARKERS (Ch 6)
MR3 Turn marker 3 on and make it the active marker MARKERS (Ch 6)
MR3? Output marker 3 on/off status MARKERS (Ch 6)
MR4 Turn marker 4 on and make it the active marker MARKERS (Ch 6)
MR4? Output marker 4 on/off status MARKERS (Ch 6)
MR5 Turn marker 5 on and make it the active marker MARKERS (Ch 6)
MR5? Output marker 5 on/off status MARKERS (Ch 6)
MR6 Turn marker 6 on and make it the active marker MARKERS (Ch 6)
MR6? Output marker 6 on/off status MARKERS (Ch 6)
MRM Display the Marker Readout menu MARKERS (Ch 6)
MRX? Output active marker number MARKERS (Ch 6)
MSFH Enterhigh loss value for shape factor calculation MARKERS (Ch 6)
MSFH? Output high loss value for shape factor calculation MARKERS (Ch 6)
MSFL Enter low loss value for shape factor calculation MARKERS (Ch 6)
MSFL? Output low loss value for shape factor calculation MARKERS (Ch 6)
MSR0 Select 0 as reference for marker search and bandwidth
calculation
MARKERS (Ch 6)
37XXXC GPIB QRG 61
FUNCTIONAL LISTING
Command Description Group
MSRD Select delta reference marker as reference for marker
search and bandwidth calculation
MSRM Select maximum as reference for marker search and
bandwidth calculation
MSRX? Output reference selection for marker search and band
width calculation
NMKR Select normal markers on active channel marker mode MARKERS (Ch 6)
SMKR Select marker search marker mode MARKERS (Ch 6)
SRCH Entermarker search value MARKERS (Ch 6)
SRCH? Output marker search value MARKERS (Ch 6)
XMKR? Output marker mode MARKERS (Ch 6)
AH0 Turn automatic DUT protection off MEASUREMENT (Ch 4)
AH1 Turn automatic DUT protection on MEASUREMENT (Ch 4)
AHX? Output automatic DUT protection on/off status MEASUREMENT (Ch 4)
AVGCNT? Output the current sweep-by-sweep average sweep
count
BH0 Turn bias off while in hold MEASUREMENT (Ch 4)
BH1 Turn bias on while in hold MEASUREMENT (Ch 4)
BHX? Output bias on/off during hold status MEASUREMENT (Ch 4)
CNTR Enter center frequency MEASUREMENT (Ch 4)
CNTR? Output center frequency MEASUREMENT (Ch 4)
CTN Continue sweeping from current point MEASUREMENT (Ch 4)
CWDEC Subtract 1 from the current CW index MEASUREMENT (Ch 4)
CWF Enter CW frequency and turn CW on MEASUREMENT (Ch 4)
CWF? OutputCW frequency MEASUREMENT (Ch 4)
CWF2I? Outputindex for frequency given MEASUREMENT (Ch 4)
CWI Enter index for CW frequency and turn CW on MEASUREMENT (Ch 4)
CWI? Output current index number MEASUREMENT (Ch 4)
CWI2F? Outputfrequency for index given MEASUREMENT (Ch 4)
CWINC Add 1 to the current CW index MEASUREMENT (Ch 4)
CWN2I Add N to the current CW index MEASUREMENT (Ch 4)
CWON Turn CW on at current CW frequency MEASUREMENT (Ch 4)
CWON? Output CW on/off status MEASUREMENT (Ch 4)
CWP Enter number of points drawn in CW MEASUREMENT (Ch 4)
CWP? Output number of points drawn in CW MEASUREMENT (Ch 4)
CWSRT SetCW frequency to the start frequency MEASUREMENT (Ch 4)
CWSTP Set CW frequency to the stop frequency MEASUREMENT (Ch 4)
EANAIN Measure External Analog In on active channel MEASUREMENT (Ch 4)
FHI Set data points to 1601 MEASUREMENT(Ch 4)
FIL Fill defined discrete frequency range MEASUREMENT (Ch 4)
MARKERS (Ch 6)
MARKERS (Ch 6)
MARKERS (Ch 6)
-
MEASUREMENT (Ch 4)
62 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
FLO Set data points to 101 MEASUREMENT (Ch 4)
FME Set data points to 401 MEASUREMENT (Ch 4)
FP0 Turn flat power correction off MEASUREMENT (Ch 4)
FP1 Turn flat power correction on MEASUREMENT (Ch 4)
FRC Clear all defined discrete frequency ranges MEASUREMENT (Ch 4)
FRI Enter Discrete Fill increment frequency MEASUREMENT (Ch 4)
FRP Enter Discrete Fill number of points MEASUREMENT (Ch 4)
STP Enter stop frequency MEASUREMENT (Ch 4)
STP? Output stop frequency MEASUREMENT (Ch 4)
FRS Enter Discrete Fill start frequency MEASUREMENT (Ch 4)
HC0 Disable internal IF calibration MEASUREMENT (Ch 4)
HC1 Enable internal IF calibration and trigger an IF calibration MEASUREMENT (Ch 4)
HCT Trigger an IF calibration MEASUREMENT (Ch 4)
HCX? Output internal IF calibration enable/disable status MEASUREMENT(Ch 4)
HLD Put sweep into hold mode MEASUREMENT (Ch 4)
HLD? Output the sweep hold status MEASUREMENT (Ch 4)
HLDX? Output hold mode (continue, restart, or single sweep) MEASUREMENT (Ch 4)
IFP Enter current front panel setup MEASUREMENT (Ch 4)
IFV Enter frequency values MEASUREMENT (Ch 4)
IS1 Enter front panel setup 1 MEASUREMENT(Ch 4)
IS10 Enter front panel setup 10 MEASUREMENT (Ch 4)
IS2 Enter front panel setup 2 MEASUREMENT(Ch 4)
IS3 Enter front panel setup 3 MEASUREMENT(Ch 4)
IS4 Enter front panel setup 4 MEASUREMENT(Ch 4)
IS5 Enter front panel setup 5 MEASUREMENT(Ch 4)
IS6 Enter front panel setup 6 MEASUREMENT(Ch 4)
IS7 Enter front panel setup 7 MEASUREMENT(Ch 4)
IS8 Enter front panel setup 8 MEASUREMENT(Ch 4)
IS9 Enter front panel setup 9 MEASUREMENT(Ch 4)
LA1 Selecta1 = Ra as phase lock for parameter being de
fined
LA2 Selecta2 = Rb as phase lock for parameter being de
fined
LAX? Output phase lock selection for parameter being defined MEASUREMENT (Ch 4)
NP101 Set data points to 101 MEASUREMENT (Ch 4)
NP1601 Set data points to 1601 MEASUREMENT(Ch 4)
NP201 Set data points to 201 MEASUREMENT (Ch 4)
NP401 Set data points to 401 MEASUREMENT (Ch 4)
NP51 Set data points to 51 MEASUREMENT (Ch 4)
-
MEASUREMENT (Ch 4)
-
MEASUREMENT (Ch 4)
37XXXC GPIB QRG 63
FUNCTIONAL LISTING
Command Description Group
NP801 Set data points to 801 MEASUREMENT (Ch 4)
ONDF Outputnumber of discrete frequencies MEASUREMENT (Ch 4)
PTP Enter the target power for flat power correction MEASUREMENT (Ch 4)
PTP? Output the target power for flat power correction MEASUREMENT (Ch 4)
PW1 Enter external source 1 power level MEASUREMENT (Ch 4)
PW1? Output external source 1 power level MEASUREMENT (Ch 4)
PW2 Enter external source power level MEASUREMENT (Ch 4)
PW2? Output external source power level MEASUREMENT (Ch 4)
PWR Enter internal source power level MEASUREMENT (Ch 4)
PWR? Output internal source power level MEASUREMENT (Ch 4)
RH0 Select RF off in hold mode MEASUREMENT (Ch 4)
RH1 Select RF on in hold MEASUREMENT (Ch 4)
RHX? Output RF on/off during hold status MEASUREMENT (Ch 4)
RT0 Turn retrace rf off MEASUREMENT (Ch 4)
RT1 Turn retrace rf on MEASUREMENT (Ch 4)
RTX? Output retrace rf on/off status MEASUREMENT (Ch 4)
S11 MeasureS11 on active channel MEASUREMENT (Ch 4)
S12 MeasureS12 on active channel MEASUREMENT (Ch 4)
S21 MeasureS21 on active channel MEASUREMENT (Ch 4)
S22 MeasureS22 on active channel MEASUREMENT (Ch 4)
SA1 Enter port 1 source attenuator value MEASUREMENT (Ch 4)
SA1? Output port 1 source attenuator value MEASUREMENT (Ch 4)
SA1MAX? Output port 1 source attenuator max value MEASUREMENT (Ch 4)
SAMP? Output the number of samplers used for measurements MEASUREMENT (Ch 4)
SAMP2 Use 2 samplers for measurements MEASUREMENT (Ch 4)
SAMP3 Use 3 samplers for measurements MEASUREMENT (Ch 4)
SPAN Enter frequency span MEASUREMENT (Ch 4)
SPAN? Output frequency span MEASUREMENT (Ch 4)
SRC2? Output external source 2 existence information MEASUREMENT (Ch 4)
SRT Enter start frequency MEASUREMENT (Ch 4)
SRT? Output start frequency MEASUREMENT (Ch 4)
SWP Return to normal sweep mode MEASUREMENT (Ch 4)
SWP? Outputsweep mode MEASUREMENT (Ch 4)
SWPDIR? Output instantaneous sweep direction forward/reverse MEASUREMENT (Ch 4)
SXX? Output s parameter or user defined parameter of active
channel
TA2 Enter port 2 test attenuator value MEASUREMENT (Ch 4)
TA2? Output port 2 test attenuator value MEASUREMENT (Ch 4)
TA2MAX? Output port 2 test attenuator max value MEASUREMENT (Ch 4)
MEASUREMENT (Ch 4)
64 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
TEX Select external (rear panel) measurement triggering MEASUREMENT (Ch 4)
TIN Select internal measurement triggering MEASUREMENT (Ch 4)
TRS Trigger/restart sweep MEASUREMENT (Ch 4)
TXX? Output trigger source internal/external/get/extddt status MEASUREMENT (Ch 4)
WFS Wait full sweep until all display data is valid MEASUREMENT (Ch 4)
DPRX? Output data pair mode visible only or pair always MEASUREMENT DATA (Ch 7)
OGCFD Output gain compression final data to GPIB MEASUREMENT DATA (Ch 7)
OGCFV Output gain compression frequency values to GPIB MEASUREMENT DATA (Ch 7)
ONP Output number of points currently being measured MEASUREMENT DATA (Ch 7)
ONPV Outputthe number of power sweep power values MEASUREMENT DATA (Ch 7)
OPSV Output power sweep power values MEASUREMENT DATA (Ch 7)
OS11C Output corrected S11 data MEASUREMENT DATA (Ch 7)
OS11R Output raw S11 data MEASUREMENT DATA (Ch 7)
OS12C Output corrected S12 data MEASUREMENT DATA (Ch 7)
OS12R Output raw S12 data MEASUREMENT DATA (Ch 7)
OS21C Output corrected S21 data MEASUREMENT DATA (Ch 7)
OS21R Output raw S21 data MEASUREMENT DATA (Ch 7)
OS22C Output corrected S22 data MEASUREMENT DATA (Ch 7)
OS22R Output raw S22 data MEASUREMENT DATA (Ch 7)
OTV Output time values for time domain MEASUREMENT DATA (Ch 7)
IMCF Enter merge calibration files from GPIB and combine MERGE CAL FILES (Ch 9)
LDMCF Load merge calibration files from disk and combine MERGE CAL FILES (Ch 9)
BDMM Define Millimeter Wave band equations MILLIMETER WAVE (Ch 9)
BSP Enter band stop frequency MILLIMETERWAVE (Ch 9)
BSP? Output band stop frequency MILLIMETER WAVE (Ch 9)
BST Enter band start frequency MILLIMETER WAVE (Ch 9)
BST? Output band start frequency MILLIMETER WAVE (Ch 9)
CLBMM Clear the new Millimeter Wave band definitions MILLIMETER WAVE (Ch 9)
E12 SetMillimeter Wave band to E band (WR-12) MILLIMETER WAVE (Ch 9)
E12E Set Millimeter Wave band to E band (WR-12) MILLIMETER WAVE (Ch 9)
F08 Set Millimeter Wave Band to F Band (WR-8) MILLIMETER WAVE (Ch 9)
Q22 Set Millimeter Wave Band to Q Band (WR-22) MILLIMETER WAVE (Ch 9)
MMBX? Output Millimeter Wave band selection MILLIMETER WAVE (Ch 9)
P1MMA Set Port 1 Millimeter Wave Head to Amplified (3742) MILLIMETER WAVE (Ch 9)
P1MMN Set Port 1 Millimeter Wave Head to None MILLIMETER WAVE (Ch 9)
P1MMR Set Port 1 Millimeter Wave Head to Receiver (3741) MILLIMETER WAVE (Ch 9)
P1MMT SetPort 1 Millimeter Wave Head to Transmit/Receiver
(3740)
P1MMX? Output Port 1 Millimeter Wave Head type MILLIMETER WAVE (Ch 9)
MILLIMETER WAVE (Ch 9)
37XXXC GPIB QRG 65
FUNCTIONAL LISTING
Command Description Group
P2MMA Set Port 2 Millimeter Wave Head to Amplified (3742) MILLIMETER WAVE (Ch 9)
P2MMN Set Port 2 Millimeter Wave Head to none MILLIMETER WAVE (Ch 9)
P2MMR Set Port 2 Millimeter Wave Head to Receiver (3741) MILLIMETER WAVE (Ch 9)
P2MMT SetPort 2 Millimeter Wave Head to Transmit/Receiver
(3740)
P2MMX? Output Port 2 Millimeter Wave Head type MILLIMETER WAVE (Ch 9)
SELBB Select Broadband test set operation MILLIMETER WAVE (Ch 9)
SELINT SelectInternal (normal) test set operation MILLIMETER WAVE (Ch 9)
SELMM Select Millimeter Wave test set operation MILLIMETER WAVE (Ch 9)
SELSP Select S-parameter test set operation MILLIMETER WAVE (Ch 9)
SELXX? Output the test set selection MMWave/Internal MILLIMETER WAVE (Ch 9)
SVBMM Saveand activate the new Millimeter Wave band defini
tions
V15 SetMillimeter Wave Band to V Band (WR-15) MILLIMETER WAVE (Ch 9)
W10 Set Millimeter Wave Band to W Band (WR-10) MILLIMETER WAVE (Ch 9)
W10E Set Millimeter Wave Band to extended W Band
(WR-10E)
IHDW Enter hardware cal data from GPIB MISCELLANEOUS (Ch 7)
IKIT Enter calkit data from GPIB MISCELLANEOUS (Ch 7)
IND Input Normalization data MISCELLANEOUS (Ch 7)
INRM Enter normalization data from GPIB MISCELLANEOUS (Ch 7)
LID Enter string for DUT identity MISCELLANEOUS (Ch 7)
LID? Output string for DUT identity MISCELLANEOUS (Ch 7)
OHDW Output hardware cal data to GPIB MISCELLANEOUS (Ch 7)
ONRM Output stored normalization data to GPIB MISCELLANEOUS (Ch 7)
BD1 Select band 1 for definition MULTIPLE SOURCE CONTROL (Ch 9)
BD2 Select band 2 for definition MULTIPLE SOURCE CONTROL (Ch 9)
BD3 Select band 3 for definition MULTIPLE SOURCE CONTROL (Ch 9)
BD4 Select band 4 for definition MULTIPLE SOURCE CONTROL (Ch 9)
BD5 Select band 5 for definition MULTIPLE SOURCE CONTROL (Ch 9)
CLB Clear all multiple source band definitions MULTIPLE SOURCE CONTROL (Ch 9)
ECW Select CW operation for component being edited MULTIPLE SOURCE CONTROL (Ch 9)
ED1 Edit source 1 equation MULTIPLE SOURCE CONTROL (Ch 9)
ED2 Edit source 2 equation MULTIPLE SOURCE CONTROL (Ch 9)
EDR Edit receiver equation MULTIPLE SOURCE CONTROL (Ch 9)
EDV Enter divisor value for equation being edited MULTIPLE SOURCE CONTROL (Ch 9)
EDV? Output divisor value for equation being edited MULTIPLE SOURCE CONTROL (Ch 9)
EML Enter multiplier value for equation being edited MULTIPLE SOURCE CONTROL (Ch 9)
EML? Output multiplier value for equation being edited MULTIPLE SOURCE CONTROL (Ch 9)
EOS Enter offset frequency for equation being edited MULTIPLE SOURCE CONTROL (Ch 9)
MILLIMETER WAVE (Ch 9)
MILLIMETER WAVE (Ch 9)
-
MILLIMETER WAVE (Ch 9)
66 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
EOS? Output offset frequency for equation being edited MULTIPLE SOURCE CONTROL (Ch 9)
ESW Select sweep operation for component being edited MULTIPLE SOURCE CONTROL (Ch 9)
EX1RF0 Turn external source 1 rf off MULTIPLE SOURCE CONTROL (Ch 9)
EX1RF1 Turn external source 1 rf on MULTIPLE SOURCE CONTROL (Ch 9)
EX2RF0 Turn external source 2 rf off MULTIPLE SOURCE CONTROL (Ch 9)
EX2RF1 Turn external source 2 rf on MULTIPLE SOURCE CONTROL (Ch 9)
EXW? Outputmultiple source sweep flag for equation being ed
ited
LTRD Output response data from the dedicated GPIB bus MULTIPLE SOURCE CONTROL (Ch 9)
LTWRT Send program data to the dedicated GPIB bus MULTIPLE SOURCE CONTROL (Ch 9)
MS0 Turn multiple source mode off MULTIPLE SOURCE CONTROL (Ch 9)
MS1 Turn multiple source mode on MULTIPLE SOURCE CONTROL (Ch 9)
MSD Select multiple source define mode MULTIPLE SOURCE CONTROL (Ch 9)
MSX? Output multiple source mode on/off/define MULTIPLE SOURCE CONTROL (Ch 9)
SRC1? Output external source 1 existence information MULTIPLE SOURCE CONTROL (Ch 9)
SRC1AC Select source 1 as active MULTIPLE SOURCE CONTROL (Ch 9)
SRC1AC? Output source 1 active/inactive status MULTIPLE SOURCE CONTROL (Ch 9)
SRC1ADD Enter external source 1 GPIB address MULTIPLE SOURCE CONTROL (Ch 9)
SRC1EX Select source 1 as external MULTIPLE SOURCE CONTROL (Ch 9)
SRC1EX? Output source 1 external/internal status MULTIPLE SOURCE CONTROL (Ch 9)
SRC1G0 Turn source 1 GPIB control off MULTIPLE SOURCE CONTROL (Ch 9)
SRC1G1 Turn source 1 GPIB control on MULTIPLE SOURCE CONTROL (Ch 9)
SRC1GX? Output source 1 GPIB control on/off status MULTIPLE SOURCE CONTROL (Ch 9)
SRC1MOD? Output external source 1 model/version string MULTIPLE SOURCE CONTROL (Ch 9)
SRC1NA Select source 1 as not active MULTIPLE SOURCE CONTROL (Ch 9)
SRC1NT Select source 1 as internal MULTIPLE SOURCE CONTROL (Ch 9)
SRC2 Select source power voltage testing MULTIPLE SOURCE CONTROL (Ch 9)
SRC2AC Select source 2 as active MULTIPLE SOURCE CONTROL (Ch 9)
SRC2AC? Output source 2 active/inactive status MULTIPLE SOURCE CONTROL (Ch 9)
SRC2ADD Enter external source 2 GPIB address MULTIPLE SOURCE CONTROL (Ch 9)
SRC2ADD? Output external source 2 GPIB address MULTIPLE SOURCE CONTROL (Ch 9)
SRC2G0 Turn source 2 GPIB control off MULTIPLE SOURCE CONTROL (Ch 9)
SRC2G1 Turn source 2 GPIB control on MULTIPLE SOURCE CONTROL (Ch 9)
SRC2GX? Output source 2 GPIB control on/off status MULTIPLE SOURCE CONTROL (Ch 9)
SRC2MOD? Output external Source 2 model/version string MULTIPLE SOURCE CONTROL (Ch 9)
SRC2NA Select source 2 as not active MULTIPLE SOURCE CONTROL (Ch 9)
SVB Save current band definitions MULTIPLE SOURCE CONTROL (Ch 9)
IODF Enter the optical file data from GPIB and calibrate OPTICAL APPLICATION (Ch 9)
LDODF Load optical data files from disk and calibrate OPTICAL APPLICATION (Ch 9)
MULTIPLE SOURCE CONTROL (Ch 9)
-
37XXXC GPIB QRG 67
FUNCTIONAL LISTING
Command Description Group
DGT Display 1st CRT test pattern PERIPHERAL TESTS (Ch 8)
DGT1 Display 1st CRT test pattern PERIPHERAL TESTS (Ch 8)
DGT2 Display 2nd CRT test pattern PERIPHERAL TESTS (Ch 8)
DGT3 Display 3rd CRT test pattern PERIPHERAL TESTS (Ch 8)
EKT Select external keyboard testing PERIPHERAL TESTS (Ch 8)
FPT Select front panel keypad testing PERIPHERAL TESTS (Ch 8)
PRT? Perform printer test and output status PERIPHERAL TESTS (Ch 8)
RPO Enter rear panel dc voltage value REAR PANEL OUTPUT (Ch 9)
RPO? Output rear panel dc voltage value REAR PANEL OUTPUT (Ch 9)
RV0 Turn rear panel output voltage off REAR PANEL OUTPUT (Ch 9)
RV1 Turn rear panel output voltage on REAR PANEL OUTPUT (Ch 9)
RV1? Output rear panel output voltage on/off status REAR PANEL OUTPUT (Ch 9)
RVD Set rear panel output mode to dc value REAR PANEL OUTPUT (Ch 9)
RVH Set rear panel output mode to horizontal REAR PANEL OUTPUT (Ch 9)
RVL Set rear panel output mode to lock direction REAR PANEL OUTPUT (Ch 9)
RVV Set rear panel output mode to vertical REAR PANEL OUTPUT (Ch 9)
RVX? Output rear panel output mode REAR PANEL OUTPUT (Ch 9)
VSP Enter rear panel stop voltage value REAR PANEL OUTPUT (Ch 9)
VSP? Output rear panel stop voltage value REAR PANEL OUTPUT (Ch 9)
VST Enter rear panel start voltage value REAR PANEL OUTPUT (Ch 9)
VST? Output rear panel start voltage value REAR PANEL OUTPUT (Ch 9)
SDR? Output receiver mode RECEIVER MODE (Ch 9)
SL1 Selectsource lock mode RECEIVERMODE (Ch 9)
ST1 Select set on mode RECEIVER MODE (Ch 9)
TK1 Select tracking mode RECEIVER MODE (Ch 9)
RC1 Recall front panel setup number 1 from memory SAVE/RECALL (Ch 8)
RC10 Recall front panel setup number 10 from memory SAVE/RECALL (Ch 8)
RC2 Recall front panel setup number 2 from memory SAVE/RECALL (Ch 8)
RC3 Recall front panel setup number 3 from memory SAVE/RECALL (Ch 8)
RC4 Recall front panel setup number 4 from memory SAVE/RECALL (Ch 8)
RC5 Recall front panel setup number 5 from memory SAVE/RECALL (Ch 8)
RC6 Recall front panel setup number 6 from memory SAVE/RECALL (Ch 8)
RC7 Recall front panel setup number 7 from memory SAVE/RECALL (Ch 8)
RC8 Recall front panel setup number 8 from memory SAVE/RECALL (Ch 8)
RC9 Recall front panel setup number 9 from memory SAVE/RECALL (Ch 8)
SV1 Save front panel setup number 1 to memory SAVE/RECALL (Ch 8)
SV10 Save front panel setup number 10 to memory SAVE/RECALL (Ch 8)
SV2 Save front panel setup number 2 to memory SAVE/RECALL (Ch 8)
SV3 Save front panel setup number 3 to memory SAVE/RECALL (Ch 8)
68 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
SV4 Save front panel setup number 4 to memory SAVE/RECALL (Ch 8)
SV5 Save front panel setup number 5 to memory SAVE/RECALL (Ch 8)
SV6 Save front panel setup number 6 to memory SAVE/RECALL (Ch 8)
SV7 Save front panel setup number 7 to memory SAVE/RECALL (Ch 8)
SV8 Save front panel setup number 8 to memory SAVE/RECALL (Ch 8)
SV9 Save front panel setup number 9 to memory SAVE/RECALL (Ch 8)
*OPT? Outputthe 488.2 options installed string SERVICE LOG (Ch 8)
CSL Clear service log SERVICE LOG (Ch 8)
PEL Print the error list SERVICE LOG (Ch 8)
ILM Enter limits status byte mask STATUS BYTE (Ch 7)
IPM Enterthe 488.2 Service Request Enable mask STATUS BYTE (Ch 7)
IEM Enterextended status byte mask STATUS BYTE (Ch 8)
CSB Clear status bytes and structures (same as *CLS) STATUS REPORTING (Ch 7)
OEB Output extended status byte STATUS REPORTING (Ch 7)
OEM Output extended status byte mask STATUS REPORTING (Ch 7)
OLB Output limits status byte STATUS REPORTING (Ch 7)
ANNCOL Enter the color number for annotation and menu text SYSTEM STATE (Ch 8)
ANNCOL? Output the color number for annotation and menu text SYSTEM STATE (Ch 8)
BC0 Turn CRT display off (disabled) SYSTEM STATE (Ch 8)
BC1 Turn CRT display on (disabled) SYSTEM STATE (Ch 8)
BCKCOL Enter the color number for background SYSTEM STATE (Ch 8)
BCKCOL? Output the color number for background SYSTEM STATE (Ch 8)
BCX? Output CRT display on/off status SYSTEM STATE (Ch 8)
BEEP0 Disable the instrument beeper on GPIB errors SYSTEM STATE (Ch 8)
BEEP1 Enable the instrument beeper on GPIB errors SYSTEM STATE (Ch 8)
BEEPX? Output GPIB beep on error enable/disable status SYSTEM STATE (Ch 8)
BRILL Activate color configuration Brilliant SYSTEM STATE (Ch 8)
CLASS Activate color configuration Classic SYSTEM STATE (Ch 8)
DATCOL Enter the color number for data SYSTEM STATE (Ch 8)
DATCOL? Output the color number for data SYSTEM STATE (Ch 8)
DATE Enter the system date SYSTEM STATE (Ch 8)
DATE? Output the system date SYSTEM STATE (Ch 8)
DC1 Display channel 1 and 2 operating parameters SYSTEM STATE (Ch 8)
DC3 Display channel 3 and 4 operating parameters SYSTEM STATE (Ch 8)
DCP Display calibration parameters 1st page SYSTEM STATE (Ch 8)
DCP1 Display calibration parameters 1st page SYSTEM STATE (Ch 8)
DCP2 Display calibration parameters 2nd page SYSTEM STATE (Ch 8)
DD0 Turn data drawing off SYSTEM STATE (Ch 8)
DD1 Turn data drawing on SYSTEM STATE (Ch 8)
37XXXC GPIB QRG 69
FUNCTIONAL LISTING
Command Description Group
DD1? Output data drawing on/off status SYSTEM STATE (Ch 8)
DF1 Display 1.0 mm female connector information SYSTEM STATE (Ch 8)
DF2 Display 2.4mm female connector information SYSTEM STATE (Ch 8)
DF3 Display GPC-3.5 female connector information SYSTEM STATE (Ch 8)
DF716 Display7/16 female connector information SYSTEM STATE (Ch 8)
DFK Display K female connector information SYSTEM STATE (Ch 8)
DFN Display N female connector information SYSTEM STATE (Ch 8)
DFN75 Display N Female 75-Ohm connector information SYSTEM STATE (Ch 8)
DFP Display Front panel instrument state SYSTEM STATE (Ch 8)
DFS Display SMA female connector information SYSTEM STATE (Ch 8)
DFSP Display Special Female connector information SYSTEM STATE (Ch 8)
DFT Display TNC female connector information SYSTEM STATE (Ch 8)
DFV Display V female connector information SYSTEM STATE (Ch 8)
DG7 Display GPC-7 Male connector information SYSTEM STATE (Ch 8)
DGS Display GPIB status information SYSTEM STATE (Ch 8)
DM1 Display 1.0 mm male connector information SYSTEM STATE (Ch 8)
DM2 Display 2.4mm male connector information SYSTEM STATE (Ch 8)
DM3 Display GPC-3.5 male connector information SYSTEM STATE (Ch 8)
DM716 Display 7/16 male connector information SYSTEM STATE (Ch 8)
DMK Display K male connector information SYSTEM STATE (Ch 8)
DMN Display N male connector information SYSTEM STATE (Ch 8)
DMN75 Display N Male 75-Ohm connector information SYSTEM STATE (Ch 8)
DMS Display SMA male connector information SYSTEM STATE (Ch 8)
DMSP Display Special Male connector information SYSTEM STATE (Ch 8)
DMT Display TNC male connector information SYSTEM STATE (Ch 8)
DMV Display V male connector information SYSTEM STATE (Ch 8)
DOASF Display band A special female connector offset-short in
formation
DOASM Displayband A special male connector offset-short infor
mation
DOBSF Display band B special female connector offset-short in
formation
DOBSM Displayband B special male connector offset-short infor
mation
DOCSF Displayband C special female connector offset-short in
formation
DOCSM Display band C special male connector offset-short infor
mation
DOF1 Display 1.0 mm female connector offset-short informa
tion
DOM1 Display 1.0 mm male connector offset-short information SYSTEM STATE (Ch 8)
-
SYSTEM STATE (Ch 8)
-
SYSTEM STATE (Ch 8)
-
SYSTEM STATE (Ch 8)
-
SYSTEM STATE (Ch 8)
-
SYSTEM STATE (Ch 8)
-
SYSTEM STATE (Ch 8)
-
SYSTEM STATE (Ch 8)
70 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
DWG Display waveguide parameters SYSTEM STATE (Ch 8)
FOF Blank frequency information SYSTEM STATE (Ch 8)
FON Display frequency information SYSTEM STATE (Ch 8)
FOX? Output frequency information on/off status SYSTEM STATE (Ch 8)
STOCO Store the current color configuration as Reset SYSTEM STATE (Ch 8)
GRTCOL Enter the color number for the graticule SYSTEM STATE (Ch 8)
GRTCOL? Output the color number for the graticule SYSTEM STATE (Ch 8)
INVER Activate color configuration Inverse SYSTEM STATE (Ch 8)
LAYCOL Enter the color number for overlay data SYSTEM STATE (Ch 8)
LAYCOL? Output the color number for overlay data SYSTEM STATE (Ch 8)
MKRCOL Enter the color number for the markers SYSTEM STATE (Ch 8)
MKRCOL? Output the color number for the markers SYSTEM STATE (Ch 8)
MNUCOL Enter the color number for the menu headers SYSTEM STATE (Ch 8)
MNUCOL? Output the color number for the menu headers SYSTEM STATE (Ch 8)
NEWCO Activate color configuration New SYSTEM STATE (Ch 8)
RST Instrument reset (same as *RST) SYSTEM STATE (Ch 8)
RST0 Reset instrument front panel memories and reserved pa-
rameters
RST1 Reset instrument and front panel memories SYSTEM STATE (Ch 8)
RSTCOL Reset color configuration to default SYSTEM STATE (Ch 8)
RTL Return to local SYSTEM STATE (Ch 8)
SOFTCO Activate color configuration Soft SYSTEM STATE (Ch 8)
SPTS? Output number of smoothing points SYSTEM STATE (Ch 8)
TIME Enter the system time SYSTEM STATE (Ch 8)
TIME? Output the system time SYSTEM STATE (Ch 8)
TRCCOL Enter the color number for memory data SYSTEM STATE (Ch 8)
TRCCOL? Output the color number for memory data SYSTEM STATE (Ch 8)
WIDE Use entire display width for graphs SYSTEM STATE (Ch 8)
DCS Select short for DC term for lowpass TIME DOMAIN (Ch 9)
DCV Enter value for DC term for lowpass TIME DOMAIN (Ch 9)
DCV? Output lowpass DC term value TIME DOMAIN (Ch 9)
DCX? Output lowpass DC term selection TIME DOMAIN (Ch 9)
DCZ Select line impedance for DC term for lowpass TIME DOMAIN (Ch 9)
DDX? Output active channel domain parameter frequency dis
tance or time
DPI Select distance phasor impulse mode for active channel TIME DOMAIN (Ch 9)
FGT Select frequency with time gate for active channel TIME DOMAIN (Ch 9)
FQD Select frequency domain for active channel TIME DOMAIN (Ch 9)
GCT Enter gate center value distance or time TIME DOMAIN (Ch 9)
SYSTEM STATE (Ch 8)
-
TIME DOMAIN (Ch 9)
37XXXC GPIB QRG 71
FUNCTIONAL LISTING
Command Description Group
GCT? Output gate center value TIMEDOMAIN (Ch 9)
GDS Gate symbols displayed on active channel TIME DOMAIN (Ch 9)
GLS Select low sidelobe gate shape TIME DOMAIN (Ch 9)
GMS Select minimum sidelobe gate shape TIME DOMAIN (Ch 9)
GNM Select nominal gate shape TIME DOMAIN (Ch 9)
GOF Turn off gating on active channel TIME DOMAIN (Ch 9)
GOF? Output gating mode on active channel TIME DOMAIN (Ch 9)
GON Turn on gating on active channel TIME DOMAIN (Ch 9)
GRT Select Rectangular gate shape TIME DOMAIN (Ch 9)
GSN Enter gate span value distance or time TIME DOMAIN (Ch 9)
GSN? Output gate span value TIME DOMAIN (Ch 9)
GSP Enter gate stop value distance or time TIME DOMAIN (Ch 9)
GSP? Output gate stop value TIME DOMAIN (Ch 9)
GST Enter gate start value distance or time TIME DOMAIN (Ch 9)
GST? Output gate start value TIME DOMAIN (Ch 9)
GSX? Output gate shape TIME DOMAIN (Ch 9)
LPI Select lowpass impulse response for active channel TIME DOMAIN (Ch 9)
LPS Select lowpass step response for active channel TIME DOMAIN (Ch 9)
LPSX? Output lowpass response for active channel impulse or
step
MRR Restore original marker range TIME DOMAIN (Ch 9)
TBP Select time bandpass mode for active channel TIME DOMAIN (Ch 9)
TDDIST Set time domain parameter to distance for active channel TIME DOMAIN (Ch 9)
TDDIST? Output active channel time domain parameter distance
or time
TDPI0 Turnphasor impulse response off for active channel TIME DOMAIN (Ch 9)
TDPI1 Turnphasor impulse response on for active channel TIME DOMAIN (Ch 9)
TDPIX? Outputphasor impulse on/off status for active channel TIME DOMAIN (Ch 9)
TDTIME Set time domain parameter to time for active channel TIME DOMAIN (Ch 9)
TDX? Output domain mode for active channel TIME DOMAIN (Ch 9)
TLP Select time lowpass mode for active channel TIME DOMAIN (Ch 9)
TPI Select time phasor impulse mode for active channel TIME DOMAIN (Ch 9)
WLS Select low sidelobe window shape TIME DOMAIN (Ch 9)
WMS Select minimum sidelobe window shape TIME DOMAIN (Ch 9)
WNM Select nominal window shape TIME DOMAIN (Ch 9)
WRT Select rectangular window shape TIME DOMAIN (Ch 9)
WSX? Outputwindow shape TIME DOMAIN (Ch 9)
ZCT Enter zoom range center value time or distance TIME DOMAIN (Ch 9)
ZCT? Output zoom range center value TIME DOMAIN (Ch 9)
TIME DOMAIN (Ch 9)
TIME DOMAIN (Ch 9)
72 37XXXC GPIB QRG
FUNCTIONAL LISTING
Command Description Group
ZSN Enter zoom range span value time or distance TIME DOMAIN (Ch 9)
ZSN? Output zoom range span value TIME DOMAIN (Ch 9)
ZSP Enter zoom range stop value time or distance TIME DOMAIN (Ch 9)
ZSP? Output zoom range stop value TIME DOMAIN (Ch 9)
ZST Enter zoom range start value time or distance TIME DOMAIN (Ch 9)
ZST? Output zoom range start value TIME DOMAIN (Ch 9)
FDH0 Select variable length arbitrary block headers TRANSMISSION METHODS (Ch 7)
FDH1 Select fixed length arbitrary block headers TRANSMISSION METHODS (Ch 7)
FDH2 Select zero length arbitrary block headers TRANSMISSION METHODS (Ch 7)
FDHX? Output arbitrary block header length selection TRANSMISSION METHODS (Ch 7)
FMT0 Select normal ascii data element delimiting TRANSMISSION METHODS (Ch 7)
FMT1 Select enhanced ascii data element delimiting TRANSMISSION METHODS (Ch 7)
FMTX? Output ascii data element delimiting mode TRANSMISSION METHODS (Ch 7)
TEB Select external trigger and executes *DDT definition TRIGGERS (Ch 7)
TIB Select GPIB measurement triggering TRIGGERS (Ch 7)
DA1 Select a1 = Ra as denominator for parameter being de-
fined
DA2 Select a2 = Rb as denominator for parameter being de-
fined
DB1 Select b1 = Ta as denominator for parameter being de-
fined
DB2 Select b2 = Tb as denominator for parameter being de-
fined
DE1 Select unity as denominator for parameter being defined USER DEFINED PARAMETERS (Ch 9)
DEN? Output denominator selection for parameter being de
fined
NA1 Select a1 as numerator for parameter being defined USER DEFINED PARAMETERS (Ch 9)
NA2 Select a2 as numerator for parameter being defined USER DEFINED PARAMETERS (Ch 9)
NB1 Select b1 as numerator for parameter being defined USER DEFINED PARAMETERS (Ch 9)
NB2 Select b2 as numerator for parameter being defined USER DEFINED PARAMETERS (Ch 9)
NU1 Select unity as numerator for parameter being defined USER DEFINED PARAMETERS (Ch 9)
NUM? Outputnumerator selection for parameter being defined USERDEFINED PARAMETERS (Ch 9)
USL Enter label string for user parameter being defined USER DEFINED PARAMETERS (Ch 9)
USL? Output label string for user parameter being defined USER DEFINED PARAMETERS (Ch 9)
USR1 Measure user parameter 1 on active channel USER DEFINED PARAMETERS (Ch 9)
USR2 Measure user parameter 2 on active channel USER DEFINED PARAMETERS (Ch 9)
USR3 Measure user parameter 3 on active channel USER DEFINED PARAMETERS (Ch 9)
USR4 Measure user parameter 4 on active channel USER DEFINED PARAMETERS (Ch 9)
USER DEFINED PARAMETERS (Ch 9)
USER DEFINED PARAMETERS (Ch 9)
USER DEFINED PARAMETERS (Ch 9)
USER DEFINED PARAMETERS (Ch 9)
-
USER DEFINED PARAMETERS (Ch 9)
37XXXC GPIB QRG 73
Loading...