Please read this instruction manual carefully and keep it for future reference
Page 2
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CA
UTION: TO REDUCE THE ELECTRIC SHOCK, DO NOT REMOVE THE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
DA
NGEROUS VOLTAGE: The lighting flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
ATTENTION: The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
RNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT
WA
TO RAIN OR MOISTURE.
WARNING: USE UNDER SUPERVISION OF AN ADULT DUE TO LONG CORD. This
unit has a long cord that can be easily tripped on or pulled on, causing injury. Please make
sure it is arranged so that it will not drape over a tabletop, etc., where it can be pulled on
by children or tripped over accidentally.
WARNING: To reduce the risk of fire or electric shock, do not
rain or moisture. The apparatus shall
objects filled with
liquids, such as vases, shall not be placed on apparatus.
not be exposed to dripping or splashing and that
2
expose this apparatus to
Page 3
IMPORTANT SAFETY INSTRUCTIONS
e
using the unit, be sure to read all operating instructions carefully. Please note that
Befor
these are general precautions and may not pertain to your unit. For example, this unit may
not have the capability to be connected to an outdoor antenna.
1.Read these instructions – All the safety and operating instructions should be read
before the appliance is operated.
2.Keep these instructions – The safety and operating instructions should be kept for
future reference.
3.Heed all warnings – All warnings on the appliance and in the operating instructions
should be adhered to.
4.Follow all instructions – All operation and use instructions should be followed.
5.Do not use this apparatus near water – The appliance should not be used near water;
for example, near a bath tub, washbowl, kitchen sink, laundry tub, in a wet basement,
or near a swimming pool.
6.Clean only with dry cloth – The appliance should be cleaned only as recommended
by the manufacturer.
7.Do not block any ventilation openings. Install in accordance with the manufacturer ’s
instructions. The appliance should be situated so that its location or position does not
interfere with its proper ventilation. For example, the appliance should not be
situated on a bed, sofa, rug, or similar surface that may block the ventilation
openings; or placed in a built-in installation, such as a bookcase or cabinet that may
impede the flow of air through the ventilation openings.
8.Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades and a third grounding prong. The wide or the third prong are
ided for your safety. If the provided plug does not fit into your outlet, consult an
prov
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments / accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of
time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
15. This appliance should not be exposed to dripping or splashing water and no object
filled with liquids such as vases should be placed on the apparatus.
16. Power Sources – The appliance should be connected to a power supply only of the
type described in the operating instructions or as marked on the appliance. Do not
overload wall outlet.
17. Battery should not be exposed to excessive heat such as sunshine, fire, etc.
18. Replace remote control battery only with the same or equivalent type.
19. Do not attempt to dismantle, open or repair this product yourself. If a problem occurs,
seek advice from your local qualified service technician or contact the distributor at
the telephone number at the back of this instruction manual.
20. Caution marking and nameplate are located on back or bottom of product.
3
Page 4
PLACEMENT AND MOUNTING
1. Placing the device on a table - Ventilati
When placing the unit and the subwoofer on an entertainment center, bookshelf, or
any type of enclosed space, be sure to allow enough space for ventilation.
Otherwise, the heat generated will produce potential heat hazard.
2-3inches
2-3inches
on
2-3inches
2-3inches
2. The Installation Distance
843mm(33.2 inches)
4
Page 5
2.1 Mounting to a wooden wall
33.2 inches
2 pieces screws
A. Mark the position of the mounting screws on the wall using a pencil.
B. Drill the screws directly into the marks that you have made on the wall and leave
approx. 0.3 inches length to hook the sound bar.
C. Put the sound bar onto the mounting screws. Make sure they are firm and stable.
(Included)
2.2 Mounting to a brick wall
2 pieces screws (Included)
A. Mark the position of the mounting screws on the wall using a pencil.
B. Drill 2 holes on wall with a powerful electric drill.
C. Insert the fixing plug and hammer into the holes.
D. Secure the screws into the fixing plug and leave approx. 0.3 inches length to hook
the sound bar.
E. Put the sound bar onto the mounting screws. Make sure they are firm and stable.
2 pieces plastic inserts (Included)
(1)
33.2 inches
(2)
5
Page 6
FRONT VIEW
PRODUCT OVERVIEW
2
1
2
CONTROL PANEL
4
3
SUBWOOFER
1.
Remote Sensor
Speaker
2.
S
B Pair Button
3.
Source Button
4.
5.
Power Button
6.
Source Indicator
Volume Down Button
7.
REAR PANEL
8
5
7
6
15
Volume Up Button
8.
HDMI ARC Port
9.
USB Port
10.
11.
AUX IN Jack
12.
OPTICAL IN Jack
LINE IN Jacks
13.
DC IN Jack
14.
9
10
INDICATOR
16
11
1213
POWER
INDICATOR
STANDBY
171819
Subwoofer
15.
Indicator
16.
Power Indicator
17.
18.
Standby Button
19.
DC IN Jack
14
DC 22V
Speaker
6
Page 7
REMOTE CONTROL
1.(Power On/Off) Button
1
HDMI
6
7
2
AUX
OPT ICAL
8
9
3
LIN E
IN
USB
10
11
4
12
13
2. AUX Button
3. LINE IN Button
4.(Previous) Button
5.
Sound Mode (MUSIC, VOICE,
MOVIE, STANDARD)
6.(Mute) Button
HDMI Button
7.
8. BT Button (Bluetooth mode)
9. OPTICAL Button
5
MUSIC
STANDARD
VOICE
Sound Mode
MOVIE
VOL
10.(Mode Switch) Button
11. USB Button
12.(Next) Button
13.Play/Pause Button
14
14.(Volume Up/Down) Button
BATTERY INSTALLATION OF REMOTE CONTROL
First time use
Remove and discard the insulation film as Fig.1.
Replacing battery for Remote Control
1. Pull out the battery holder as Fig.2.
2. Replace the old button cell with a new CR2025 button cell
with the polarity markings facing upward as Fig.3.
3. Push back the battery holder as Fig.4.
OPEN
3V CR 2025
Fig.1
3V CR 2025
OPEN
Fig.2
Fig.3
7
Fig.4
Page 8
BATTERY PRECAUTIO
F
ollow these precautions when using a battery in this device:
NS
1. Use only the size and type of battery specified.
2. Be sure to follow the correct polarity when installing the battery as
ompartment, a reserved battery may cause damage to
c
3. Do not mix different types of batteries together ( e.g: Alkaline and
the device.
Carbon
indicated
in the battery
-zinc )
or old batteries with fresh ones.
period of time,
4. If the batteries in the device are consumed or the device is not to be used for
remove the batteries to prevent damage or injury from
5. Do not try to recharge the battery
Follow
(
the battery manufacturer’s instructions.)
as it is not intended to be recharged; it can
possible
leakage.
6. The batteries shall not be exposed to excessive heat such as sunshine or fire
7. Clean the battery contacts and also those of the device prior to battery
8.
The remote control is supplied with a coin/button cell battery. If the
a long
overheat
.
installation.
and rupture.
coin button cell battery is swallowed, it can cause severe internal
burns in just 2 hours and can lead to death. Keep new and used
battery away from children. If the Battery compartment does not
close securely, stop using the product and keep it away from
CR2025
children. If you think batteries might have been swallowed or placed
any part of the body, seek immediate medical attention.
AUTION
C
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
●
●
Battery cannot be subjected to high or low extreme temperatures, low air pressure at high altitude during
use, storage or transportation.
Replacement of a battery with an incorrect type that can result in an explosion or the leakage of
●
flammable liquid or gas.
●
Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can
result in an explosion.
Leaving a battery in an extremely high temperature surrounding environment that can result in an
●
explosion or the leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure that may result in an explosion or the leakage of
●
flammable liquid or gas.
Remote control operation range
When there is an obstacle between the transmitter
●
and the unit, the unit may not operate.
When direct sunlight, an incandescent lamp,
●
fluorescent lamp or any other
on the REMOTE SENSOR of the unit, the
operation of the remote may be unstable.
stronglight
shines
16.4 Feet (5M)
HDMI
AUX
OPTICAL
LINE
USB
IN
VOICE
MOVIE
MUSIC
Sound Mode
STANDARD
VOL
8
Page 9
GENERAL OPERATION
1.Connect the DC 22V, 1.9A Adapter to the DC IN jack on the Unit. Plug the
Adapter into the AC outlet with AC100-240V~ 50/60Hz. The mode indicator on
the Unit will light up and turn RED.
2.
Connect the DC 22V, 1.9A Adapter to the DC IN jack on the subwoofer. Plug the
Adapter into the AC outlet with AC100-240V~ 50/60Hz. The power indicator on
the subwoofer will light up and turn RED.
3.
Press the button on the unit or remote controlto power on the unit, the blue
indicator blanks.
4. After a few seconds, the unit will be connected with subwoofer automatically,
the indicator on subwoofer will be solid blue.
IMPORTANT NOTE: If the pairing INDICATOR on the SUBWOOFER is off, it means
the Main Unit is not connected with the SUBWOOFER successfully. Please operate
as the steps below:
A: Press and hold the SB Pair button on the Main Unit for 3-5 seconds.
B: Press and hold the STANDBY button on SUBWOOFER to power off, then press
the STANDBY button on SUBWOOFERto power on again, the pairing
INDICATOR
the
SUBWOOFER is connected with Main Unit successfully.
C: Press the SB PAIR button on the Main Unitthe pairing INDICATOR on
SUBWOOFER will be solid BLUE.
the
on SUBWOOFER will blink several times and then turn off, it means
on ec
again,
5. Press the
button on the unit or remote control repeatedly to switch to the
desired mode. Or press the HDMI, AUX, OPTICAL, , LINE IN, USB button
on remote control to turn to desired mode, the indicator on top of the unit will
~ Press the + or - button on the unit or remote control repeatedly to adjust volume.
~ Press the button on remote control to turn off sound, the mode indicator on
the unit will blink, press the button again to resume.
~ Press the MUSIC button on remote control to turn to MUSIC sound effect mode.
~ Press the VOICE button on remote control to turn to VOICE sound effect mode.
~ Press the MOVIE button on remote control to turn to MOVIE sound effect mode.
~ Press the STANDARD button on remote control to turn to normal sound effect
mode.
7.
Press the button on the unit or remote control to power off the unit.
Press and hold the STANDBY button on the subwoofer to power off subwoofer.
BLUETOOTH OPERATION
1. Power on the unit and subwoofer and pair as previously explained.
Press the button on the unit or remote control repeatedly, or press the
2.
button on remote control to switch to the Bluetooth mode directly, the indicator
on top of the unit will turn Blue and blink.
3. Power on the external Bluetooth enable device and enter Bluetooth mode and try
searching the unit.
4. When
5.
After successful paired, the indicator will stop blinking and a beep tone will beheard.
6. During playback:
~ Press the or button on remote control to skip tracks.
~ Press the button on remote control to pause, press it again to resume.
7. Press and hold the button to disconnect current connection and go into a
pairing mode, you can pair to new devices with this sound bar.
NOTE: The unit will be automatically connected with the last connected Bluetooth
device if their Bluetooth function are activated and they are in working range.
42963554
appears, select it and make connection.
10
Page 11
AUX IN OPERATION
An external Audio player (such as mobile phone, MP3 player etc.) can be
connected to this unit and listen through the unit's speakers.
1. Plug one end of the AUX IN cable into the AUX IN jack on the rear of unit.
2. Plug another end of the AUX IN cable into the headphone jack or Aux Out jack
on the external audio player.
Rear View
MP3 Player
Connect to the Phones; AUX Out;
Line Out Jack of the external devices
(Such like MP3 Player; cell phones;
iPod/iPad ... etc)
Mobile Phone
3. Power on the unit and subwoofer and pair as previously explained.
Press the button on the unit or remote control repeatedly, or press the AUX
4.
button on remote control to switch to the AUX IN mode directly, the indicator on
top of the unit will turn Green.
5. Power on the connected external player and start playback the music as usual.
11
Page 12
LINE IN OPERATION
An external Audio/Video player (such as TV, DVD player etc.) can be connected
to this unit and listen through the unit's speakers.
1. Plug one end of the line in cable into the LINE IN jacks (L&R) on the rear of unit.
Plug the other end of the line in cable into the Line Out jacks (L&R) on TV or
2.
DVD player etc.
Rear View
white
red
Line out jacks of
TV/DVD player etc.
LR
Video
3. Power on the unit and subwoofer and pair as previously explained.
Press the button on the unit or remote control repeatedly, or press the LINE
4.
IN button on remote control to switch to LINE IN mode directly, the indicator on
top of the unit will turn Violet.
5. Power on the connected external player and start playback the music as usual.
12
Page 13
OPTICAL-IN OPERATION
1. Connect the Optical out jack from the external audio player (such as TV, DVD
player etc.) to the OPTICAL IN jack on the rear of the unit with the optical
connection cable as illustated below: (For PCM format only)
Rear View
Optical Connection Cable
(Not included)
2. Power on the unit and subwoofer and pair as previously explained.
Press the button on the unitor remote control repeatedly, or press the
3.
OPTICAL button on remote control to switch to the OPTICAL IN mode directly,
the indicator on top of the unit will turn Orange.
TV or DVD player etc.
OPTICAL OUT
4. Power on the connected external player and start playback the music as usual.
Turn on the digital audio output and set it to PCM (Pulse Code Modulation) type
similar to the below figure:
Picture
Sound ModeStandard
Bass
Treble
Balance
SurroundOff
AVLOff
Digital OutputPCMDigital OutputPCM
Audio LanguageEnglish
AudioAudio
Select
Time
Setup
Move
Lock
MENU
Off
Exit
13
Page 14
HdMI IN OPERATION
TV with HDMI IN ARC port can be connected to this unit, and play audio through
the speakers.
1. Plug one end of the HDMI cable into the HDMI IN ARC port on the rear of unit.
2. Plug the other end of the HDMI cable into the HDMI IN ARC port on TV.
Rear View
HDMI IN ARC port
of the TV
LR
HDMI IN ARC
Video
3. Power on the unit and subwoofer and pair as previously explained.
4.
Press the button on the unit or remote control repeatedly, or press the
HDMI button on remote control to switch to the HDMI mode directly, the
indicator on top of the unit will turn Cyan.
5. Power on the connected TV and start playback as usual.
Explanation:
ARC (Audio Return Channel)
NOTE: The HDMI input channel only works for TV with HDMI IN with ARC feature.
Please make sure the HDMI cable is connected to the HDMI ARC Port or refer to
the TV user manual.
14
Page 15
USB PLAYBACK
1. Plug the USB player to the USB port at the rear panel of the unit.
Rear View
USB
2. Power on the unit and subwoofer and pair as previously explained.
Press the button on the unit or remote control repeatedly, or press the USB
3.
button on remote control to switch to the USB mode directly, the indicator on
top of the unit will turn Indigo.
4. During playback:
~ Press the or button on remote control to skip tracks.
~ Press the button on remote control to pause, press it again to resume.
15
Page 16
TROUBLESHOOTING
SYMPTOM
No power
No sound or
sound weak
Sound distortion/rattle
Remote Control
not functioning
POSSIBLE CAUSE
The adapter is not connected
The unit is in power off mode
Volume level in minimum position
The paired/connected device is
not in playback mode
Input source incorrect
Volume level too high
Out of range
The battery in the remote
control is drained
POSSIBLE SOLUTION
Connect the adapter to the unit and wall outlet.
Press and hold the power/source button on
the unit or press the button on remote
control to power on the unit.
Raise the volume level by pressing the +
button on the unit or remote control.
Play music/movie in the paired/connected
device as usual and make sure the volume
level of it is in high level.
Press the power/source button repeatedly or
press the button on remote control to
switch to desired mode.
Reduce the volume level by pressing the button on the top of the unit or remote control
Reduce the volume level of the paired/
onnected device.
c
Point the remote control to the remote sensor
on the unit within 16 feet, +/-30 degress.
Replace with new battery.
Bluetooth
reception failure
HDMI IN(ARC)
not working
The external device is too far
from the unit
Have not paired
Not insert to HDMI ARC channel
The ARC control is off
16
Put the external BT device close
Pair the unit with the BT Device as the
procedures stated in this manual.
Please read which channel is the ARC
channel for your TV, and insert this HDMI
cable to HDMI ARC channel. it only works in
HDMI ARC channel.
Please go to the TV setup menu, turn on the
CEC control and turn on the ARC from the
setup menu.
to the unit.
Page 17
SPECIFICATIONS
Power input ...........................................................................AC 100-240V~ 50/60Hz
Power output ......................................................................DC 22V 1.9A
Audio output of the unit...............................................................................4 x 12.5W
Audio output of the subwoofer.............................................................................50W
Bluetooth effective working range in open area......................................up to 32 feet
Remote effective working range..............................................................up to 16 feet
PACKAGES
1x Unit
1x Subwoofer
1x User Manual
1x Remote Control
1x AUX IN Cable
1x LINE IN Cable
1x Power Adapter for the Unit
1x Power Adapter for the Subwoofer
2x Plastic Inserts ( For Wall Mount )
2x Metallic Screws ( For Wall Mount )
SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE
WITHOUT NOTICE
17
Page 18
Warranty CARD
12 Month Warranty
Thank you for your purchase from Kmart.
Kmart Australia Ltd warrants your new product to be free from defects in materials and
workmanship for the period stated above, from the date of purchase, provided that the product
is used in accordance with accompanying recommendations or instructions where provided.
This warranty is in addition to your rights under the Australian Consumer Law.
Kmart will provide you with your choice of a refund, repair or exchange (where possible)for
this product if it becomes defective within the warranty period. Kmart will bear the reasonable
expense of claiming the warranty. This warranty will no longer apply where the defect is a
result of alteration, accident, misuse, abuse or neglect.
Please retain your receipt as proof of purchase and contact our Customer Service Centre on
1800 124 125 (Australia) or 0800 945 995 (New Zealand) or alternatively, via Customer Help
at Kmart.com.au for any difficulties with your product. Warranty claims and claims for expense
incurred in returning this product can be addressed to our Customer Service Centre at 690
Springvale Rd, Mulgrave Vic 3170.
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
For New Zealand customers, this warranty is in addition to statutory rights observed under
New Zealand legislation.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.