Angelcare AC7127 Instruction manual
Model AC127
Baby Movement Monitor,
with Sound
OWNER’S MANUAL
WARNING
Keep user’s guide for future reference. Please read the warnings and
safety instructions carefully before assembling & using the product.
Failure to follow the warnings and the instructions could result in serious
injury or death or damage to the product.
IMPORTANT INTENDED USE
is product is NOT intended and should NOT be used to prevent Sudden Infant Death Syndrome (SIDS).
is product is NOT intended to diagnose, treat, mitigate, cure or prevent any disease or condition.
is is a product to monitor the movement of healthy babies and is not a substitute for parental care.
is baby monitor is compliant with all relevant standards regarding electromagnetic fields and is, when
handled as described in the User’s Guide, safe to use
WARNINGS
1. Because of the serious strangulation risk to infant & toddlers, parents & caregivers should note
the following Warnings
WARNING
- Strangulation Hazard –
Children have STRANGLED in cords
• KEEP the Nursery Unit and adaptor cords OUT of the
reach of children more than 3 feet or 1 metre away
• NEVER use extension cords with adaptors. ONLY use
adaptors provided
• is product is NOT a Toy. NEVER allow children to
play with it
2.
WARNING
- MOVEMENT SENSOR PAD - NO ALARM
• Sources of vibration & movement other than your baby’s can be detected by
the Sensor Pad and interfere with the performance of your Angelcare monitor
• e alarm will not sound if it detects movement other than your baby’s
• High sensitivity settings can pick up other sources of vibration & movements please read instructions on sensitivity setting to adjust accordingly
• Other active and older babies (toddlers) in the same room can be detected and
the alarm will not sound
• Ensure the baby’s environment is FREE from any movements or vibrations when
using the Sensor Pad - see below warnings 3 to 11
3. DO NOT use a cot mobile and other cot
accessories that may produce movements or
vibrations
4. Fans (including ceiling), washing machines, floor
boards, central he ating or loud music are all forms
of movement and vibration and may in terfere and be
detected by the Sensor Pad
5. If an additional Nursery Unit is added then it
must be positioned at leas t 2 metres minimum from
Nursery Unit 1 and Sensor Pad as this could interfere
with performance
6. DO NOT use with bedside cot touching parent’s/
carer’s bed as the Sensor Pad will detect your
movements
7. DO NOT place the cot against a wall or skirting
board as vibrations may be de tected
8. Following removal of baby from the co t, some
mattresses may s till detec t mat tress movement due
to it forming back into shape and alarm may not sound
9. Ensure cot is stable to elimina te any movement
2
2
10. Cot should no t be placed in reaching distance of
another cot or bed
11. DO NOT use o ther w ireless devices in t he same
room as the monitor (including mobile phones,
microw aves...). ey may inter fere with signal and
performance
12. e Sensor Pad is made of plastic and does
not permit air to circulate. erefore, mildew
build up could develop underneath t he mat tress in
the Sensor Pad area
We suggest rotating & airing /drying the mattress
regularly to prevent any mildew. AVOID CONTACT
WITH MOISTURE. Clean - wipe with a dry lint free
cloth
13. e Se nsor Pad is no t suitab le for use abo ve
age 24 months
14. is product cannot replace responsible
adult supervision
• is product is designed to aid in the monitoring of
your child. When using the monitor, you must still
provide the supervision necessary for the continued
safety of your child
• Use this appliance ONLY for its intended use as
described in this manual
15. e Sensor Pad is not intended to be used
to determine if a child is out of the co t
16. ALWAYS be sure to immediately check on
baby whenever an alarm sounds
17. Keep cords out of the reach of ANY children
18. ONLY use the chargers and power adaptors
provided. Do not use other types as this
may damage the device and bat tery pack (if
included in your model)
19. Adult assembly required. Keep small parts
away from children when assembling
20. Follow instructions and test this monitor
and its functions so you are familiar with it
prior to actual use. ALWAYS be sure t hat both the
transmitter and receiver are working properly and are
within range of each other – check periodically and
when changing location of t he Nursery Unit
21. DO NOT touch the plug contacts especially
with sharp or metal objects
22. DO NOT use the baby monitor near wa ter
Care should be taken so that objects DO NOT fall
onto units and that liquids are not spilled into either
unit or S ensor Pad through i ts openings
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DO NOT EXPOSE TO RAIN OR MOISTURE
23. Keep monitor AWAY from heat sources
(such as stoves, radiators, etc.). Heat can
damage the case or elec trical par ts
24. ALWAYS place both the Nursery Unit and the
Parent Unit on a flat solid surface in an upright
position that allows for proper VENTILATION. DO
NOT place on sofas, cushions, beds, etc. which may
block ventilation or anywhere t hat would muffle the
sound or inter fere with the normal flow of air
25. e baby monitor can only be used between
10°C and 40°C (50°F and 104°F)
WARNINGS AND SAFETY
INSTRUCTIONS BATTERY SPECIFIC
26. ALWAYS keep all ba tterie s away from ch ildren
27. e Parent Unit batteries are replaceable
Nickel-Metal-Hydride batteries. e Wireless
Sensor Pad uses a replaceable Button Cell
Lithium Battery. Only use the Angelcare
recommended replacement battery (see
Technical Specification)
• Danger of explosion if the wrong battery is used
or if replaced incorrectly. Refer to User’s Guide for
correct battery installation
• DO NOT short circuit supply terminals
28. DO NOT mix old and new batteries and only
use Angelcare recommended replacement
batteries (see Technical Specification)
29. is product contains a Button Cell Battery
and if swallowed can cause internal chemical
burns in as little as two hours and lead to
death. Dispose of used batteries immediately.
Keep new and used batteries away from
children. If you think batteries might have
been swallowed or placed inside any of the
body, seek medical attention.
30. e Button Cell Battery represents a small
part and a choking hazard – KEEP away from
children!
31. Exercise care in handling batteries in order
not to short out the batteries w ith conducting
materials such as rings, bracelets and keys
32. Overcharging, short circuiting, reverse
charging, mutilation, or incineration of
batteries must be avoided to prevent one or
more of the following occurrences: release of toxic
materials, release of hydrogen and/or oxygen, gas
and rise in surface temperature
33. DO NOT attempt to recharge batteries
provided with or identified for use wi th this
product that are not intended to be charged.
e bat teries may leak cor rosive elec trolyte or
explode
34. Incorrect polarity installation of the
batteries in the end product mus t be avoided.
Reverse insertion of batteries can cause charging,
and that may result in leakag e or explosion
35. Remove bat teries from units if you store
the product over 30 days because the batteries
could leak and damage the product
36. Discard ‘dead’ batteries as soon as possible
since ‘dead’ bat teries are more likely to leak in a
product. If a bat tery has leaked or vented, discard
product responsibly
37. DO NOT store this product, or the bat teries
provided with or identified for use wi th this
product, in high-temperature & high humidity
environments and avoid direct sunlight
IMPORTANT SAFETY INSTRUCTIONS
38. Sensor Pad –
• If your cot does not have a solid, stationary,
completely flat, firm surface including a spring or
slat base, place a hard board between the cot base
and the Sensor Pad, to ensure correct operation
(see specification on STEP 2)
• e Sensor Pad functions with standard cot sprung
and foam mattresses and not memory foam (partial
or full), hollow frame construction mattresses and
water beds. Please consult Angelcare if unsure of
mattress compatibility
39. is monitor uses public airwaves to transmit
signals. e Parent Unit may pick up signals or
inter ference from other nursery monitors in your
area. Your monitor may even be picked up by other
households. To protec t your privacy, make sure both
units are turned OFF when no t in use
40. Power cord protection - Protect the
3
3
E
E
N
N
Adaptor’s power cord from being walked on
or pinched by furniture or other items – Power
supply cords should be routed so that they are not
likely to be walked on or pinched by items upon or
against them, paying par ticular at tention to cords
and plugs, convenience receptacle, and t he point
where t hey exit from the product. e socket outle t
should be installed near the equipment and should
be easily accessible. Make sure to plug the adaptor
to the socket outle t nearest to the equipment and
that is easily accessible. To disconnect from mains,
unplug the adaptor
41. Only use attachments/accessories
and replacement parts specified by the
manufacturer. Any mounting of the product
should follow the manufacturer’s instructions
• DO NOT position this product on an unstable cart,
stand, tripod, bracket or table. e product may fall,
causing serious injury to a child or adult and serious
damage to the product
• Use ONLY the stand sold with the product
• Be sure replacement parts are supplied by Angelcare
and have the same characteristics as original
part. Unauthourised substitution may result in fire,
SET UP REQUIREMENTS
WHAT’S IN THE BOX
1
Parent Unit
2
Nursery Unit
3
Stand (for Nursery Unit)
4
Sensor Pad
5
CR2450 Battery
(for Sensor Pad)
6
2 x AC Adaptors
7
2 x Rechargeable AAA
Batteries (for Parent Unit)
WHAT YOU NEED
• Hardboard, if the cot does not
have a firm surface
(see ‘IMPORTANT’ note step 2)
• 2 x alkaline AAA backup
batteries (for Nursery Unit)
• Posidrive screwdriver
1
4
electric shock or fire
42. Unplug this appliance during lightning storms
or when not used for long periods of time
43. Servicing - DO NOT attemp t to service
this product yourself as opening or removing
covers (except battery door) may expose you
to dangerous voltage or other hazards
• Power Supply – see Technical Specification within
this guide
44. Overloading - DO NOT overload wall outlets,
extension cords or integral convenience
receptacles as this can result in a risk of fire or
electric shock
45. Nursery Unit Antenna - e antenna used
for this transmitter mus t be installed to provide a
separation distance of at least 8’’ (20 cm) from all
persons and mus t not be collocated or operating in
conjunction with any other antenna or transmi tter
46. Cleaning - Disconnect all units before cleaning.
DO NOT immerse in water any part of the monitor.
Clean only with dry cloth
2
3
5
6
2X
7
2X
4
1 SETTING UP THE PARENT UNIT
Charge the Parent Unit
10 hours prior to first use
1
10H
2
Regular charging time is
8 hours
2 SETTING UP THE SENSOR PAD
e Sensor Pad is designed to detect subtle baby movements on the surface of the
mattress.e alarm will only sound if NO movement is detected for 20 seconds.
E
N
1
1. Remove the battery cover
and insert the battery face
with + face up
2. Replace the battery cover,
align 2 dots and click to
secure
2
3
3. Remove the mattress from
the cot, place Sensor Pad
- Angelcare® logo
side up - on base in
approximate centre of
mattress. It should be
centred on the hardboard
if your cot requires a
hardboard support (see
‘IMPORTANT’ note below)
4. Replace the mattress
Correct positioning
for slatted base
5
Loading...