Angelcare AC7027 Instruction manual

Model AC027

Baby Movement Monitor

OWNER’S MANUAL

WARNING

Keep user’s guide for future reference. Please read the warnings and
safety instructions carefully before assembling & using the product.
Failure to follow the warnings and the instructions could result in serious
injury or death or damage to the product.

IMPORTANT  INTENDED USE

is product is NOT intended and should NOT be used to prevent Sudden Infant Death Syndrome (SIDS).
is product is NOT intended to diagnose, treat, mitigate, cure or prevent any disease or condition.
is is a product to monitor the movement of healthy babies and is not a substitute for parental care.

is baby monitor is compliant with all relevant standards regarding electromagnetic fields and is, when
handled as described in the User’s Guide, safe to use

WARNINGS

1.

WARNING

• KEEP the Nursery unit out of the reach of children more than 3 feet or 1 meter away

• is product is NOT a Toy. NEVER allow children to play with it

2.

WARNING

- MOVEMENT SENSOR PAD - NO ALARM

• Sources of vibration & movement other than your baby’s can be detected by
the Sensor Pad and interfere with the performance of your Angelcare monitor

• e alarm will not sound if it detects movement other than your baby’s

• High sensitivity settings can pick up other sources of vibration & movements ­please read instructions on sensitivity setting to adjust accordingly

• Other active and older babies (toddlers) in the same room can be detected and
the alarm will not sound

• Ensure the baby’s environment is FREE from any movements or vibrations when
using the Sensor Pad - see below warnings 3 to 10

3. DO NOT use a cot mobile and other cot
accessories that may produce movements or
vibrations

4. Fans (including ceiling), washing machines, floor
boards, central hea ting or loud music are all forms
of movement and vibration and may interfere and be
detected by the Sensor Pad

5. If an addit ional Nursery Unit is added then it
must be positioned at least 2 metres minimum from
Nursery Unit 1 and Sensor Pad as this could interfere
with performance

6. DO NOT use with bedside cot touching parent’s/
carer’s bed as the Sensor Pad will de tect your
movements

7. DO NOT place the cot against a wall or skirting
board as vibrations may be detected

8. Following removal of baby f rom the cot, some
mattresses may still detect ma ttress movement due
to it forming back into shape and alarm may not sound

9. Ensure cot is stable to eliminate any movement

10. Cot should not be placed in reaching dis tance o f

another cot or bed
11 . DO NOT use o ther wireless devices in the same

room as the monitor (including mobile phones,
microwaves...). ey may interfere with sig nal and
performance

2

2

12 . e Sensor Pad is made of plastic and does
not permit air to circulate. erefore, mildew build

up could develop underneath the mattress in the
Sensor Pad area
We suggest rotating & airing /drying the mattress
regularly to prevent any mildew. AVOID CONTACT
WITH MOISTURE. Clean - wipe with a dry lint f ree
cloth

13. e Sensor Pad is not suitable for use above
age 24 months

14. is product canno t replace responsible
adult supervision

• is product is designed to aid in the monitoring of
your child. When using the monitor, you must still
provide the supervision necessary for the continued
safety of your child

• Use this appliance ONLY for its intended use as
described in this manual

15. e Sensor Pad is not intended to be used to

determine if a child is out of the cot

16. ALWAYS be sure to immediately check on

baby whenever an alarm sounds

17. Adult assembly required. Keep small parts

away from children when assembling

18. Follow instructions and test this monitor

and its functions so you are familiar with it
prior to actual use. ALWAYS be sure that both the

transmitter and receiver are working properly and are
within rang e of each other – check periodically and
when changing location of the Nursery Unit

19. DO NOT use the baby monitor near water

Care should be taken so that objects DO NO T fall
onto units and that liquids are no t spilled into ei ther
unit or Sensor Pad through its openings

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

DO NOT EXPOSE TO RAIN OR MOISTURE

20. Keep monitor AWAY from heat sources (such
as stoves, radiators, etc.). Heat can damage the

case or electrical parts

21 . ALWAYS place both the Nursery Unit and the
Parent Unit on a flat solid surface in an uprig ht
position that allows for proper VENTILATION. DO

NOT place on sofas, cushions, beds, etc. which may
block ventilation or anywhere that would mu ffle the
sound or inter fere with the normal flow of air

22 . e baby monitor can only be used between
10°C and 40°C (50°F and 104°F)

WARNINGS AND SAFETY
INSTRUCTIONS  BATTERY SPECIFIC

23. A LWAYS keep all batteries away from children

24. e Wireless Sensor Pad uses a replaceable
Button Cell Lithium Bat tery. Only use the
Angelcare recommended replacement battery
(see Technical Specification)

• Danger of explosion if the wrong battery is used
or if replaced incorrectly. Refer to User’s Guide for
correct battery installation

• DO NOT short circuit supply terminals

25. DO NOT mix old and new batteries and only

use Angelcare recommended replacement
batteries (see Technical Specification)

26. is product contains a Button Cell Battery

and if swallowed can cause internal chemical
burns in as little as two hours and lead to
death. Dispose of used batteries immediately.
Keep new and used batteries away from
children. If you think batteries might have
been swallowed or placed inside any of the
body, seek medical attention.

27. e Button Cell Battery represents a small

part and a choking hazard – KEEP away from
children!

28. Exercise care in handling batteries in order

not to short out the batteries with conducting

mater ials such as ring s, bracelets and keys

29. Overcharging, short circuiting, reverse

charging, mutilation, or incineration of

batteries must be avoided to prevent one or

more of the following occurrences: release of toxic
mater ials, release of hydrogen and/or oxygen, gas
and rise in surface temperature

30. DO NOT attempt to recharge batteries
provided with or identified for use with this
product that are not intended to be charged

e batteries may leak corrosive electrolyte or explode

31. Incorrect polarity installation of the
batteries in the end product must be avoided

Reverse insertion of batteries can cause charging,
and that may result in leakage or explosion

32. Remove bat teries from units if you store
the product over 30 days because the batteries

could leak and damage the product

33. Discard ‘dead’ batteries as soon as possible
since ‘dead’ b atteries are more likely to leak in a
product. If a battery has leaked or vented, discard
product responsibly

34. DO NOT store this product, or the batteries
provided with or identified for use with this
product, in high-temperature & high humidity
environments and avoid direct sunlight

IMPORTANT SAFETY INSTRUCTIONS

35. Sensor Pad –

• If your cot does not have a solid, stationary,
completely flat, firm surface including a spring or
slat base, place a hard board between the cot base
and the Sensor Pad, to ensure correct operation
(see specification on STEP 2)

• e Sensor Pad functions with standard cot sprung
and foam mattresses and not memory foam (partial
or full), hollow frame construction mattresses and
water beds. Please consult Angelcare if unsure of
mattress compatibility

36. Only use attachments/accessories

and replacement par ts specified by the
manufacturer. Any mounting of the product
should follow the manufacturer’s instructions

• DO NOT position this product on an unstable cart,
stand, tripod, bracket or table. e product may fall,
causing serious injury to a child or adult and serious
damage to the product

• Use ONLY the stand sold with the product

• Be sure replacement parts are supplied by Angelcare
and have the same characteristics as original part.
Unauthorised substitution may result in fire, electric
shock or fire

37. Nursery Unit Antenna - e antenna used

for this transmitter must be installed to provide a
separation distance of at least 8’ ’ (20 cm) from all
persons and must not be collocated or operating in
conjunction with any other antenna or transmitter

38. Cleaning - Disconnect all units before cleaning.

DO NOT immerse in water any part of the monitor.
Clean only with dry cloth

E

E

N

N

3

3

SET UP REQUIREMENTS

WHAT’S IN THE BOX

1

Nursery Unit

2

Stand (for Nursery Unit)

3

Sensor Pad

4

CR2450 Battery

(for Sensor Pad)

1

3

2

WHAT YOU NEED

• Hardboard, if the cot does not
have a firm surface
(see ‘IMPORTANT’ note - Step 1)

• 2 x AAA batteries (for Nursery Unit)

• Posidrive screwdriver

1 SETTING UP THE SENSOR PAD

e Sensor Pad is designed to detect subtle baby movements on the surface of the
mattress.e alarm will only sound if NO movement is detected for 20 seconds.

1

2

3

1. Remove the battery cover

and insert the battery
face with + face up

2. Replace the battery cover,

align 2 dots and click
to secure

3. Remove the mattress from

the cot, place Sensor Pad

- Angelcare® logo side
up - on base in approximate

centre of mattress. It should
be centred on the hardboard
if your cot requires a
hardboard support (see
‘IMPORTANT’ note below)

4. Replace the mattress

4

Correct positioning

for slatted base

4