Andis TS-1 User Manual

MODEL TS-1

Item pictured may differ from actual product

El artículo ilustrado puede diferir del producto real

Il est possible que l’article sur la photo soit différent du produit réel

Use & Care Instructions

TS-1

ENGLISH

Please read the following instructions before using your new Andis
shaver. Give it the care that a fine precision built instrument
deserves and it will give you years of service.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions
should always be followed, including the following: Read

all instructions before using the Andis shaver.

DANGER: To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water.
Unplug immediately.

2. Do not use while bathing or in a shower.

3. Do not place or store appliance where it can fall or be
pulled into a tub or sink. Do not place in or drop into
water or other liquid.

4. Always unplug this appliance from the electrical outlet
immediately after using.

5. Unplug this appliance before cleaning, removing, or
assembling parts.

WARNING: To reduce the risk of burns, fire, electric

shock, or injury to persons:

1. An appliance should never be left unattended when plugged
in.

2. Close supervision is necessary when this appliance is used
by, on or near children or individuals with certain
disabilities.

3. Use this appliance only for its intended use as described in
this manual. Do not use attachments not recommended by
Andis.

4. Never operate this appliance if it has a damaged cord or
plug, if it is not working properly, if it has been dropped or

2 3

damaged, or dropped into water. Return the appliance to
an Andis Authorized Repair Station for examination or
repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any opening.

7. Do not use outdoors or operate where aerosol (spray)
products are being used or where oxygen is being
administered.

8. Do not use this appliance with a damaged or broken foil
or cutter, as injury to the skin may occur.

9. Always attach plug to appliance first, then to outlet.
To disconnect, turn all controls to OFF, then remove plug
from outlet.

SAVE THESE INSTRUCTIONS

THIS PRODUCT INTENDED FOR PROFESSIONAL USE

OPERATING INSTRUCTIONS

CHARGING SHAVER

This battery charger is intended for use with Andis model TS-1 lithium­ion battery with a rated capacity of 3.7V
and AC adapter from the carton. Plug the adapter into a 100/240V AC
outlet, or according to your local power standards. Note that the shaver
ON/OFF switch must be in the OFF position for the battery to charge.
Plug the cord adapter directly into the inlet on bottom of shaver
(Figure A). The green charging indicator light on the shaver will turn on.

The shaver has not been charged at the factory. Please charge the
shaver for 2 hours before the first use for maximum performance.

You can keep the shaver plugged into the adapter when not in use. The
adapter will maintain the battery at full charge and the green charging
indicator light will stay on. The adapter should be unplugged if the
shaver won’t be used for seven or more days.

2.8 Wh. Remove the shaver

Grasp both

sides of cutter

and pull up

Assembly
Lock
Button
(Not shown)

Foil
Assembly

Grasp both

sides of cutter

and pull up

A

Dual Foils

FAILURE TO CHARGE

1. Make sure voltage is present at the wall outlet (confirm with an

appliance you know is working).

2. Check to make sure adapter cord is plugged firmly into shaver. Twist

Foil Assembly

the adapter connector slightly to insure good electrical connection.
If failure to charge still exists, return shaver to Andis or an Andis
Authorized Service Station for examination and repair or replacement.

On/Off Switch

Assembly
Lock Button

(Not shown)

USE WITH CORD ADAPTER

If the shaver powers OFF while in use, the power cord can be attached
to continue use in corded operation (Figure A). When the shaver is
running with the power cord attached, the green charging indicator
light will remain off, even if the battery is partially or fully discharged.
The shaver will not charge while in use with the cord attached.

This power unit is intended to be correctly orientated in a vertical
or floor mount position.

FOR SHAVING

1. Keep the unit clean and dry at all times.

2. Remove the protective plastic headguard.

3. Check to make sure the outer foils and inner cutters are not

damaged. Replace damaged parts before using. For more

Cord
Adapter
Inlet

(Not shown)

Green
Charging
Indicator Light

Cord Adapter

information on replacement parts, contact Andis or the nearest

B

Foil
Assembly

C

Grasp both

sides of cutter

and pull up

Andis Authorized Service Station.

4. Ensure that the battery is charged.

5. Wash and dry your skin thoroughly prior to shaving.

6. Slide the ON/OFF switch up to the ON position.

7. Gently stretch the skin of your face with your free hand while moving

the shaver slowly and smoothly against the grain of your beard. Using
short, circular strokes will make the hairs stand out from your face
and make shaving easier. Hold the shaver at a 90 degree angle to
your face while maintaining contact with the foil.

8. In order to achieve the closest shave and avoid unnecessary wear on

Assembly
Lock
Button
(Not shown)

the foils, be sure that both foils contact the skin simultaneously
at all times. Holding the shaver at an angle where only one foil

contacts the skin will cause distortion of the foil and may result in
skin irritation.

4 5

9. To facilitate cutting and avoid foil wear, use minimal pressure to apply
the shaver to your skin.

10. To maximize shaving comfort, be sure to clean the shaver

thoroughly after use.

CLEANING

Regular cleaning is necessary in order to maintain the optimal
performance and maximum comfort from your shaver. Do NOT run
shaver, foil assembly or cutters under water. Use only the small brush
(included) to clean.

USER MAINTENANCE

If shaver is to remain unused for a long period of time, store in a safe,
cool, dry place. Do not wrap cord tightly around shaver. Do not hang
the shaver by the power cord. Other than the recommended
maintenance described in this manual, no other maintenance should be
performed, except by Andis Company or an Andis Authorized Service
Station. To find an Andis Authorized Service Station near you log on

to www.andis.com or contact our customer service department:
1-800-558-9441 (U.S.) or 1-800-335-4093 (Canada).

IMPORTANT: For best shaver performance and results, it is
recommended that you replace your shaver’s foil assembly and
cutters every six months.

TO REPLACE FOIL ASSEMBLY

1. Remove the foil assembly by pressing the round assembly lock
button located on the right side of the shaver. Grasp the foil
assembly on both sides and gently lift it off the shaver (Figure B).

2. Position the replacement foil assembly over the cutters. Be careful
not to damage the foils. Gently slide the foil assembly down until it
snaps firmly into place.

TO REPLACE CUTTERS

NOTE: Always replace the foil assembly when replacing the cutters.

1. To remove a cutter, grasp it on both sides and pull up (Figure C).

2. To replace a cutter, hold it on both sides and line up the small metal
shaft on its underside with the notch on the shaver drive and push
down firmly until it snaps into place.

3. Replace foil assembly.

6 7

DRY CLEANING WITH BRUSH

1. Remove the foil assembly by pressing the round button located on
the right side of the unit. Grasp the foil assembly on both sides and
gently lift it off of shaver (Figure C).

2. Gently tap the base of the foil assembly on a flat surface so that the
hairs inside fall out. Do not remove the foils or they may be damaged
accidentally.

3. Lightly brush the hairs out from the cutters. You can remove them
from the shaver if necessary. Blow out any remaining loose hairs.

4. Replace the cutters and foil assembly.

USE GUIDELINES FOR LITHIUM-ION BATTERIES

1. The lithium-ion battery included with your shaver does not develop a
“memory effect” like a nickel-metal hydride (NiMH), or nickel
cadmium (NiCd) battery. You can return the shaver to the charger at
any time for a full charge, or even use the battery before a charge
cycle is complete. Like most rechargeable batteries, lithium-ion
batteries perform best when used frequently.

2. For maximum battery life, store the shaver in a partially discharged
condition if it will not be used for several months. To discharge the
battery, run the shaver until it automatically shuts off.

3. Avoid locating the shaver near heat vents, radiators, or in direct
sunlight. Optimum charging will result where the temperature is
stable. Sudden increases in temperature can result in the battery
receiving less than a full charge.

4. Many factors influence lithium-ion battery life. A battery that has
received heavy use or is more than a year old may not give the same
run-time performance as a new battery pack.

5. New lithium-ion batteries, unused for a period of time, may not
accept a full charge. This is normal and does not indicate a problem
with the battery or charger. The battery will accept a full charge after
several cycles of shaver use and recharging.

6. Disconnect the charger or the shaver from the AC outlet if extended
periods of non-use are anticipated.