Andis SMC User Manual

MODEL SMC

LITERATURE PACKET #04974

Item pictured may differ from actual product

El artículo ilustrado puede diferir del producto real

Il est possible que l’article sur la photo soit différent du produit réel

Use & Care Instructions

ENGLISH

Please read the following instructions before using your new Andis
clipper. Give it the care that a fine precision built instrument deserves
and it will give you years of service.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should
always be followed, including the following: Read all

instructions before using the Andis clipper.

DANGER:

1. Do not reach for an appliance that has fallen into water.
Unplug immediately.

2. Do not use while bathing or in a shower.

3. Do not place or store appliance where it can fall or be
pulled into a tub or sink. Do not place in or drop into
water or other liquid.

4. Always unplug this appliance from the electrical outlet
immediately after using.

5. Unplug this appliance before cleaning, removing or
assembling parts.

To reduce the risk of electric shock:

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any opening.

7. Do not use outdoors or operate where aerosol (spray)
products are being used or where oxygen is being
administered.

8. Do not use this appliance with a damaged or broken
blade or comb, as injury to the skin may occur.

9. To disconnect turn control to OFF then remove plug from
outlet.

10. WARNING: During use, do not place or leave appliance
where it may be (1) damaged by an animal or (2) exposed
to the weather.

SAVE THESE INSTRUCTIONS

THIS PRODUCT INTENDED FOR PROFESSIONAL USE

IMPORTANT INFORMATION

Your new clipper contains a microchip – please note the following:

• When the unit is plugged in, you may experience slight movement in the
blade. This is normal as the microchip powers up.

• If you unplug your clipper, please wait 30 seconds before plugging it back
in to allow the microchip to be reset.

WARNING: To reduce the risk of burns, fire

electric shock, or injury to persons:

1. An appliance should never be left unattended when
plugged in.

2. Close supervision is necessary when this appliance is used
by, on or near children or individuals with certain disabilities.

3. Use this appliance only for its intended use as described
in this manual. Do not use attachments not recommended
by Andis.

4. Never operate this appliance if it has a damaged cord or
plug, if it is not working properly, if it has been dropped
or damaged, or dropped into water. Return the appliance
to an Andis Authorized Service Station for examination
and repair.

2 3

OPERATING INSTRUCTIONS

Plug cord into electrical outlet, operate at 120 volt, 60 cycle AC electrical current
or as noted on the unit.

5-SPEED UNIT OPERATION

Your clipper is equipped with five cutting speeds. The speeds are adjusted using
the arrows on either size of the power button (Figure A). Lower speeds are
recommended for use on your dog’s face, belly, under the tail, and on puppies or
dogs that are new to grooming. Higher speeds are recommended for use on
your dog’s body coat and for dogs that are comfortable being groomed. To start
your clipper, press the power button. To increase your blade speed, press the up
arrow. To decrease your blade speed, press the down arrow. To shut your clipper
off, press the power button. After using your clipper, rewrap cord, and store in a
safe place.

REMOVING BLADE SET

OIL

OIL

OIL

INCORRECT

To remove blade set, first make sure your clipper motor is switched OFF. Push
blade release mechanism under blade hinge (Figure B). While holding down the
blade release mechanism, push down on blade, then gently pull the blade
forward (Figure C), and slide it off the blade hinge. If your blade hinge should
snap closed and is flush with the clipper, use a small standard screwdriver to pry
the tongue of the hinge out (Figure D). NOTE: Hair may accumulate in the front
cavity of the housing under the blade. If this happens, you can clean out the hair
by brushing out the cavity with a small brush or an old toothbrush while the
blade is off the clipper.

REPLACING OR CHANGING BLADE SET

To replace or change your blade set, slide the blade bracket onto the hinge of
the clipper (Figure E) and with the clipper turned ON, push the blade towards
the clipper to lock into position.

USER MAINTENANCE

The internal mechanism of your motor clipper has been permanently lubricated
by the factory. Other than the recommended maintenance described in this
manual, no other maintenance should be performed, except by Andis Company,
or an Andis Authorized Service Station. To find an Andis Authorized Service
Station near you log on to www.andis.com or contact our customer service
department: 1-800-558-9441 (U.S.) or 1-800-335-4093 (Canada).

FIGURE A FIGURE B FIGURE C

FIGURE D

FIGURE E

FIGURE F

BLADE TEMPERATURE

Due to the high speed nature of Andis clippers, please check for blade heat
often, especially on close cutting blades. If blades are too hot, dip the blades
only into Andis Blade Care Plus or apply Andis Cool Care Plus and then Andis

BLADE
DRIVE
MOUNTING
SCREWS

Clipper Oil. If you have a detachable blade unit, you can change your blade in
order to maintain a comfortable temperature; using multiple blades of the same
size is popular among groomers.

CARE AND SERVICING OF YOUR ANDIS CLIPPER BLADES

FIGURE G

FIGURE H

FIGURE I

Blades should be oiled before, during, and after each use. If your clipper blades
leave streaks or slow down, it’s a sure sign blades need oil. Place a few drops of
Andis Clipper Oil on the front and side of the cutter blades (Figure F). Wipe
excess oil off blades with a soft dry cloth. Spray lubricants contain insufficient oil
for good lubrication, but are an excellent clipper blade coolant. Always replace
broken or nicked blades to prevent injury. You can clean the excess hair from
your blades by using a small brush or worn out tooth brush. To clean the blades
we suggest to immerse the blades only into a shallow pan of Andis Clipper Oil,

CORRECT
POSITION
OF
DRIVE
BEARING

POSITION
OF DRIVE
BEARING

while the clipper is running. Any excess hair and dirt that has accumulated
between the blades should come out. After cleaning, turn your clipper OFF and
dry blades with a dry cloth and start clipping again.

4 5

FIGURE J

FIGURE K

FIGURE L

If upon cleaning your blades you find that the blades will still not cut, there may
be a few fine pieces of hair trapped between the upper and lower blade. If this
happens, you will need to snap the blade off the clipper. Proceed to slide the
upper blade to one side, without loosening the tension spring or moving the
upper blade completely out from under the tension spring (See Figure G for
position of blade). Wipe the surface between the blades clean with a dry cloth,
then place a drop of clipper oil where the upper and lower blades meet and also
in the guide slot of the tension spring (Figure G). Now slide the upper blade to
the opposite side of the lower blade and repeat this process. After completing
this procedure, slide the upper blade, centering it over the lower blade. Handle
or store your Andis Clipper with the blades down so excess oil will not run into
the clipper case.

CHANGING THE BLADE DRIVE ASSEMBLY

If your clipper blades no longer cut properly (be sure to try more than one blade,
since the blade currently being used may be dull), it could be that your blade
drive assembly needs replacement.

To change the blade drive assembly:

1. Remove blade set (Figure C).

2. Remove drive cap (Figure H).

3. Remove blade drive mounting screws (Figure I).

4. NOTE: Before removing blade drive assembly, note the way it is positioned

(this will help you in reassembly). Remove blade drive assembly (Figure J).

5. Drive bearing should be at its lowest position, if not, move it with your finger

to lowest position (Figures K & L).

6. Put on new drive assembly, align screw holes and press down (Figure J).

7. Reassemble blade drive by mounting screws (Figure I).

8. Replace drive cap (Figure H).

9. Replace blade (Figure E).

FACTORY REPAIR SERVICE

When the blades of your Andis clipper become dull after repeated use, it is
advised to purchase a new set of blades available through your Andis supplier
or through an Andis Authorized Service Station. Some blade sets can be
resharpened – contact Andis Company for information on resharpening. To find
an Andis Authorized Service Station near you log on to www.andis.com or
contact our customer service department: 1-800-558-9441 (U.S.) or
1-800-335-4093 (Canada).

Sírvase leer las instrucciones siguientes antes de usar su nueva
recortadora Andis. Al brindar el cuidado que se merece un instrumento
fino construido con precisión, obtendrá muchos años de servicio.

PRECAUCIONES IMPORTANTES

Al usar un artefacto eléctrico, siempre deben seguirse ciertas
precauciones básicas, que incluyen la siguiente: Lea todas

las instrucciones antes de usar la recortadora de acabado
Andis.

PELIGRO: Para reducir el riesgo de descarga

eléctrica:

1. Si un artefacto se ha caído al agua, no trate de sacarlo.
Desenchúfelo inmediatamente.

2. No lo utilice al bañarse en tina o bajo la regadera.

3. No coloque ni almacene el artefacto donde pueda caerse
en una bañera o un lavabo, o ser halado dentro de éstos.
No la coloque ni la deje caer en agua u otro líquido.

4. Siempre desenchufe este aparato del tomacorriente
eléctrico inmediatamente después de usarlo.

5. Desenchufe este artefacto antes de limpiar, desmontar o
montar las piezas.

ADVERTENCIA: Para reducir el riesgo de

quemaduras, incendio, descarga eléctrica o lesiones a las
personas:

1. Un artefacto nunca debe dejarse desatendido mientras
está enchufado.

2. Es necesaria una supervisión estrecha cuando este
artefacto sea usado por, en o cerca de niños o personas

SPANISH

con ciertas discapacidades.

Caution: Never handle your Andis clipper while you are operating a water
faucet, and never hold your clipper under a water faucet or in water. There is
danger of electrical shock and damage to your clipper. Andis Company will

not be responsible in case of injury due to this carelessness.

3. Utilice este artefacto exclusivamente para su uso
propuesto, tal como se describe en este manual.
No utilice accesorios no recomendados por Andis.

4. Nunca opere este artefacto si su cable eléctrico o
enchufe está dañado, si no está funcionando

6 7