Andis RS-1 User Manual

Item pictured may differ from actual product

El artículo ilustrado puede diferir del producto real

Il est possible que l’article sur la photo soit différent du produit réel

Use & Care Instructions

RS-1

ENGLISH

Please read the following instructions before using your new Andis
clipper. Give it the care that a fine precision built instrument
deserves and it will give you years of service.

the appliance to an Andis Authorized Repair Station for
examination or repair.

5. Keep the cord away from heated surfaces.

6. Never drop or insert any object into any opening.

7. Do not use outdoors or operate where aerosol (spray)
products are being used or where oxygen is being

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should
always be followed, including the following: Read all

instructions before using your Andis clipper.

DANGER: To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water.
Unplug immediately.

2. Do not use while bathing or in a shower.

3. Do not place or store appliance where it can fall or be
pulled into a tub or sink. Do not place in or drop into
water or other liquid.

4. Always unplug this appliance from the electrical outlet
immediately after using.

5. Unplug this appliance before cleaning, removing, or
assembling parts.

WARNING: To reduce the risk of burns, fire,

electric shock, or injury to persons:

1. An appliance should never be left unattended when

plugged in.

2. Close supervision is necessary when this appliance is

administered.

8. Do not use this appliance with a damaged or broken
blade or comb, as injury to the skin may occur.

9. To disconnect turn control to OFF then remove plug
from outlet.

10. This appliance is not intended for use by children and
other persons whose physical, sensory, or mental
capabilities or lack of experience and knowledge
prevents them from using the appliance safely without
supervision or instruction by a responsible person to
ensure that they can use the appliance safely. Children
should be supervised by the responsible person to
ensure that they do not play with the appliance.

SAVE THESE INSTRUCTIONS

THIS PRODUCT INTENDED FOR HOUSEHOLD USE

To reduce the risk of electric shock, this appliance has a polarized plug (one
blade is wider than the other). This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install the proper outlet. Do
not change the plug in any way.

used by, on or near children or individuals with certain
disabilities.

3. Use this appliance only for its intended use as
described in this manual. Do not use attachments not
recommended by Andis.

4. Never operate this appliance if it has a damaged cord

OPERATING INSTRUCTIONS

Before starting clipper remove blade guard. Plug cord into electrical outlet,
operate at 120 volt, 60 cycle AC electrical current or as noted on the unit.
To start clipper move switch button forward, to stop, move switch button
back to original position. After using your Andis clipper, rewrap cord and
store in a safe place.

or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. Return

2 3

USING THE ATTACHMENT COMBS

(Some models do not have combs and sizes will vary by kit)

You can set the blades for a longer cut by using any of the attachment
combs made for your Andis clipper. The combs mount easily; simply slip the
cutter blade teeth into comb and snap the comb down. To remove, simply
snap off (Figures A & B). These attachment combs guide hair into the blades
and give you precise control of hair lengths. The length of trim is indicated
on the attachment comb. Use the chart below to find the approximate
lengths of cut. Different blade angles in relation to the skin, thickness and
texture of the hair will vary the cutting length.

A

B

SNAP!

CLIPPING GUIDE

Approx. Length of Cut
Description Clipping Direction Fine Coarse

Standard Andis Blade With hair grain 1/16" (1.6 mm) 3/16" (4.8 mm)
Against hair grain 1/32" (0.8 mm) 1/8" (3.2 mm)

1/16" Attachment Comb With hair grain 3/16" (4.8 mm) 5/16" (7.9 mm)
Against hair grain 3/32" (2.4 mm) 5/32" (4.0 mm)

1/8" Attachment Comb With hair grain 1/4" (6.4 mm) 3/8" (9.5 mm)
Against hair grain 1/8" (3.2 mm) 1/4" (6.4 mm)

1/4" Attachment Comb With hair grain 3/8" (9.5 mm) 1/2" (12.7 mm)
Against hair grain 1/4" (6.4 mm) 3/8" (9.5 mm)

3/8" Attachment Comb With hair grain 1/2" (12.7 mm) 5/8" (15.9 mm)
Against hair grain 3/8" (9.5 mm) 1/2" (12.7 mm)

1/2" Attachment Comb With hair grain 5/8" (15.9 mm) 7/8" (22.2 mm)
Against hair grain 1/2" (12.7 mm) 5/8" (15.9 mm)

5/8" Attachment Comb With hair grain 3/4" (19.0 mm) 1" (25.4 mm)
Against hair grain 5/8" (15.9 mm) 7/8" (22.2 mm)

3/4" Attachment Comb With hair grain 7/8" (22.2 mm) 1-1/8" (28.6 mm)
Against hair grain 3/4" (19.0 mm) 1" (25.4 mm)

7/8" Attachment Comb With hair grain 1" (25.4 mm) 1-1/4" (31.8 mm)
Against hair grain 7/8" (22.2 mm) 1-1/8" (28.6 mm)

1" Attachment Comb With hair grain 1-1/8" (28.6 mm) 1-3/8" (34.9 mm)
Against hair grain 1" (25.4 mm) 1-1/4" (31.8 mm)

4 5

C

ADJUSTMENT
LEVER

E

OIL

CLIPPER BLADE ADJUSTMENT

Your Andis adjustable clipper blade set is easy to adjust. From coarse to fine
cuts, all that is needed is a flick of the adjustment lever with your thumb. In
the upright position, the blades are set for the finest, or shortest cuts
(Figure C).

D

POWER SCREW

F

USER MAINTENANCE

The internal mechanism of your clipper has been permanently lubricated at
the factory. Other than the recommended maintenance described in this
manual, no other maintenance should be performed, except by Andis
Company or an Andis Authorized Service Station.

nicked blades to prevent injury. You can clean the excess hair from your
blades by using a small brush or an old toothbrush. To clean the blades we
suggest immersing the blades only into a shallow pan of Andis Clipper Oil
while the clipper is running. Any excess hair and dirt that has accumulated
between the blades should come out. After cleaning, turn your clipper off,
dry the blades with a dry cloth, and start clipping again.

POWER ADJUSTMENT

Your Andis clipper has been adjusted to line voltage at the factory. However,
because of voltage variations, it may be necessary to adjust the power
setting for your area. If the power adjustment is off, you will usually notice a
“clatter” when the clipper is on or introduced into the hair. (It is normal for
your clipper to “clatter” for an instant when initially turned on).

TO ADJUST YOUR CLIPPER

1. Oil the blades.

2. The power screw is located in the lower part of the housing opposite the

switch (Figure D).

3. Turn your clipper ON.

4. Using a screwdriver that fits the slot, turn the power screw clockwise until

the clipper clatters continuously. Then turn the screw counterclockwise
carefully until the clatter ceases.

5. Your clipper is now adjusted to its optimum power setting.

The power screw is a special part and it must not be replaced by any other
screw except the original part of the appliance.

BLADE TEMPERATURE

Due to the high speed nature of Andis clippers, please check for blade heat
often, especially on close cutting blades. If blades are too hot, dip the
blades only into Andis Blade Care Plus or apply Andis Cool Care Plus and
then Andis Clipper Oil. If you have a detachable blade unit, you can change
your blade in order to maintain a comfortable temperature; using multiple
blades of the same size is popular among groomers.

REMOVING AND REPLACING THE BLADE SET

To remove the blades, first unplug the clipper from the electrical outlet.
Turn the clipper upside down so that the blade teeth are pointing down.
You may want to place the clipper on a flat surface to do this. Unscrew the
screws on the blades. Remove the blades.

To replace the blades, put the smaller, upper blade back into position
(Figure F). Line up the screw holes in the bottom blade with the two holes in
the clipper housing, and replace the screws. Do not tighten down the
screws completely. Turn the clipper over and align the lower blade so the
teeth on both blades are parallel, but with the lower blade’s teeth slightly
above the upper blade’s teeth. Failure to do this may result in nipping the
skin when cutting the hair.

FACTORY REPAIR SERVICE

When the blades of your Andis clipper become dull after repeated use,
it is advised to purchase a new set of blades available through your Andis
Supplier or through an Andis Authorized Service Station. If you wish your
trimmer to be serviced as well, it should be carefully packed and mailed either
Parcel Post Insured, or U.P.S. to any Andis Authorized Service Station. To find
an Andis Authorized Service Station near you log on to www.andis.com or
contact our customer service department: 1-800-558-9441 (U.S.) or
1-800-335-4093 (Canada).

CARE AND SERVICING OF YOUR ANDIS CLIPPER BLADES

The blades should be oiled before, during, and after each use. If your
clipper blades leave streaks or slow down, it’s a sure sign the blades need
oil. The clipper should be held in the position shown in Figure D to prevent
oil from getting into motor. Place a few drops of Andis Clipper Oil on the
front and side of the cutter blades (Figure E). Wipe excess oil off the blades
with a soft, dry cloth. Spray lubricants contain insufficient oil for good
lubrication, but are an excellent clipper coolant. Always replace broken or

6 7