Andis ORL User Manual

USE & CARE INSTRUCTIONS

MODEL ORL

LITERATURE PACKET #04987

Item pictured may differ from actual product

El artículo ilustrado puede diferir del producto real

Il est possible que l’article sur la photo soit différent du produit réel

ENGLISH

Please read the following instructions before using your new Andis trimmer.
Give it the care that a fine precision built instrument deserves and it will give
you years of service.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions
should always be followed, including the following:

Read all instructions before using the Andis trimmer.

DANGER: To reduce the risk of electric shock:

1. Do not reach for an appliance that has fallen into water.
Unplug immediately.

2. Do not use while bathing or in a shower.

3. Do not place or store appliance where it can fall or be
pulled into a tub or sink. Do not place in or drop into water
or other liquid.

4. Except when charging, always unplug this appliance from
the electrical outlet immediately after using.

5. Unplug this appliance before cleaning, removing or
assembling parts.

WARNING: To reduce the risk of burns, fire,

electric shock, or injury to persons:

1. An appliance should never be left unattended when
plugged in.

2. This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.

3. Children should be supervised to ensure that they do not

play with the appliance.

4. Use this appliance only for its intended use as described in

this manual. Do not use attachments not recommended by
Andis.

2 3

5. Never operate this appliance if it has a damaged cord or
plug, if it is not working properly, if it has been dropped
or damaged, or dropped into water. Return the appliance
to an Andis authorized service station for examination
and repair.

6. Keep the cord away from heated surfaces.

7. Never drop or insert any object into any opening.
Do not use outdoors or operate where aerosol (spray)

8.
products
administered.

9. Do not use this appliance with a damaged or broken
blade or comb, as injury to the skin may occur.

10. To disconnect turn control to OFF then remove plug from
outlet.

11. Use of a charger not sold by Andis may result in risk of
fire, electric shock, or injury to person.

12. Do not disassemble charger. Incorrect reassembly may
result in a risk of electric shock or fire. When repair is
required, sent or take it to an Andis authorized service
station.

13. The battery in this clipper is designed to provide
maximum trouble-free life. However, like all batteries, it
will eventually wear out. Do not attempt to replace
battery. When repair or replacement is required, send or
take it to an Andis authorized service station.

14. Batteries can be harmful to the environment if disposed
of improperly. Many communities offer recycling or
battery collection. Contact your local government about
disposal practices in your area.

15. Plug adapter cord directly into an AC outlet. Do not use

an extension cord.

16. WARNING: Never touch both terminals on clipper with

metal objects and/or body parts, as short circuit may
result. Keep away from children. Failure to comply with
these warnings could result in fire or serious injury.

are being used or where oxygen is being

17. WARNING: During use, do not place or leave appliance

where it may be 1) damaged by an animal or 2) exposed
to the weather.

SAVE THESE INSTRUCTIONS

THIS PRODUCT INTENDED FOR PROFESSIONAL USE

OPERATING INSTRUCTIONS

CHARGING TRIMMER USING CHARGING STAND

The AC adapter is intended for use with Andis model ORL lithium-ion trimmer
battery with a rated capacity of 4.5V
from the carton. Plug the AC adapter into a 120V AC outlet, or according to your
local power standards. Plug the adapter cord into the receptable on the back of the
charging stand (Figure A). Place trimmer in the charging stand. The ON/OFF switch
on the trimmer must be in the OFF position for the battery to charge. The blue
light on the trimmer will fade in and out while charging. Note that the trimmer can
be removed at any time during the charging cycle without harming the trimmer or
battery. Once the battery is fully charged, the light on the trimmer (Figure B) will
turn solid blue.

The trimmer has not been charged at the factory. Please charge the trimmer
for 2 hours before the first use for maximum performance.

You can keep the trimmer plugged into the charging stand or adapter when not
in use. The charging stand or adapter will maintain the battery at full charge.
We recommend that the charging stand or adapter be unplugged if the trimmer
won’t be used for seven or more days.

1.2A. Remove the trimmer and AC adapter

A C

D

G

B

LIGHT BOTTOM OF TRIMMER

E

H

OIL

F

I

BLADE

SCREWS

FAILURE TO CHARGE

1. Make sure voltage is present at the wall outlet (confirm with an appliance you
know is working).

2. Make sure on/off switch on the trimmer is OFF.

3. Check to make sure adapter cord is plugged firmly into trimmer or charging
stand. Twist the adapter cord slightly to ensure good electrical connection.

4. If failure to charge still exists, return trimmer to Andis or an Andis authorized
service station for examination and repair or replacement.

J

LK

ATTACHMENT

SCREW

CORDED OPERATION

If the trimmer powers OFF in the middle of a trimming job, the power cord can be
attached to continue use in corded operation. Plug the adapter cord directly into
the bottom of the trimmer (Figure C). When the trimmer is running with the adapter
cord attached, the blue light will remain solid ON to indicate strong power, even if
the battery is not fully charged. The trimmer will charge at a slower rate while in
use with the cord attached.

4 5

TRIMMER
INDICATOR LIGHTS

When the trimmer is
running in a cordless
operation, a blue trimmer
indicator light (Figure B)
means the battery has a
strong charge. When the
light turns red, the battery
level is low and should be
recharged as soon as
possible. If the trimmer
automatically powers OFF,
move the power switch to
the OFF position and
either charge in the
charging stand or plug in
to cord to continue
trimming. The trimmer
automatically powering off protects the lithium-ion battery and is not a malfunction.
The trimmer will resume normal operation when it is recharged or plugged in to its
power cord. The ORL trimmer, by design, will run at full power until the

battery is fully depleted.

NOTE: If trimmer automatically powers OFF while in use, it may take 1-2
minutes to resume normal operation after power cord is plugged in.

USING ATTACHMENT COMBS

(Some models do not have combs and sizes will vary by kit)

Your trimmer may come with 4 attachment combs: 1/16", 1/8", 1/4" and 3/8"
(Figure D). To use, slide front of attachment comb over the teeth of the blade
(Figure E). Snap comb down over back of blade (Figure F). Use the trimming guide
to find the approximate lengths of cut. Different blade angles in relation to the skin,
thickness and texture of the hair will vary the cutting length.

USER MAINTENANCE

If trimmer is not going to be used for a long period of time, store in a safe, cool,
dry place. Do not wrap adapter cord tightly around trimmer. Do not hang the
trimmer by the adapter cord.

The internal mechanism of your trimmer has been permanently lubricated at the
factory. Other than the recommended maintenance described in this manual, no
other maintenance should be performed, except by Andis Company or an Andis
authorized service station. To find an Andis authorized service station near you

log on to www.andis.com or contact our customer service department:
1-800-558-9441.

6 7

TRIMMER INDICATOR LIGHT STATUS

Trimmer in Charging Stand

Fully Charged Solid Blue

Charging Blue Fade In and Out

Trimmer in Use (Cordless)

Full Charge Solid Blue

Low Charge Solid Red

Trimmer in Use (Corded)

Running Solid Blue

OFF with Full Charge Solid Blue

OFF without full charge Blue Fade In and Out

TRIMMING GUIDE

Description Clipping Direction Length of Cut

Standard Andis Blade With hair grain 1/16" (1.6 mm)
Against hair grain 1/32" (0.8 mm)

1/16" Attachment Comb With hair grain 3/16" (4.7 mm)
Against hair grain 1/16" (1.6 mm)

1/8" Attachment Comb With hair grain 1/4" (6.4 mm)
Against hair grain 1/8" (3.2 mm)

1/4" Attachment Comb With hair grain 3/8" (9.5 mm)
Against hair grain 1/4" (6.4 mm)

3/8" Attachment Comb With hair grain 1/2" (12.7 mm)
Against hair grain 3/8" (9.5 mm)

Approximate

CARE AND SERVICING OF YOUR ANDIS TRIMMER BLADES

The blades should be oiled before, during, and after each use. If your trimmer
blades leave streaks or slow down, it’s a sure sign that the blades need oil. The
trimmer should be held in the position shown in Figure G to prevent oil from
getting into the motor. Place a few drops of Andis Clipper Oil on the front and side
of the cutter blades (Figure H). Wipe excess oil off the blades with a soft dry cloth.
Spray lubricants contain insufficient oil for good lubrication, but are an excellent
trimmer coolant. Discontinue use of broken or nicked blades to prevent injury. You
can clean the excess hair from your blades by using a small brush or an old
toothbrush. To clean the blades we suggest immersing the blades only into a
shallow pan of Andis Blade Care Plus, while the trimmer is running. Any excess hair
and dirt that has accumulated between the blades should come out. After cleaning,
turn your trimmer off, dry the blades with a soft, dry cloth and start trimming again.

REPLACEMENT OF BLADE SET

Your trimmer has a preset tension assembly on the blade set. To remove blade set
from your trimmer, remove from charger base or unplug from power cord. Hold the
trimmer so that the blade teeth are pointing up. Using a phillips-head type
screwdriver, unscrew the blade attachment screw (Figure I). Press forward on blade
(Figures J & K). To replace the blade, line up the bottom hook of blade with the
slot on the trimmer and snap into place (Figure L). Replace blade attachment screw
and gently hand tighten. There is no need to adjust blade tension before use, as
tension has been preset at the factory.