ANALOG DEVICES ADXRS610 Service Manual
V
www.BDTIC.com/ADI
±300°/sec Yaw Rate Gyro
FEATURES
Complete rate gyroscope on a single chip
Z-axis (yaw rate) response
High vibration rejection over wide frequency
2000 g pow
Ratiometric to referenced supply
5 V single-supply operation
105°C operation
Self-test on digital command
Ultrasmall and light (< 0.15 cc, < 0.5 gram)
Temperature sensor output
RoHS compliant
APPLICATIONS
Vehicle chassis rollover sensing
Inertial measurement units
Platform stabilization
ered shock survivability
GENERAL DESCRIPTION
The ADXRS610 is a complete angular rate sensor (gyroscope)
that uses the Analog Devices, Inc. surface-micromachining
process to create a functionally complete and low cost angular
rate sensor integrated with all required electronics on one chip.
The manufacturing technique for this device is the same high
volume BiMOS process used for high reliability automotive
airbag accelerometers.
The output signal, RATEOUT (1B, 2A), is a voltage proportional
angular rate about the axis normal to the top surface of the
to
package. The output is ratiometric with respect to a provided
reference supply. A single external resistor can be used to lower
the scale factor. An external capacitor sets the bandwidth. Other
external capacitors are required for operation.
A temperature output is provided for compensation techniques.
T
wo digital self-test inputs electromechanically excite the sensor
to test proper operation of both the sensor and the signal
conditioning circuits. The ADXRS610 is available in a 7 mm ×
7 mm × 3 mm BGA ceramic package.
FUNCTIONAL BLOCK DIAGRAM
+5
(ADC REF)
ADXRS610
100nF
+5V
AV
CC
100nF
AGND
+5V
V
DD
100nF
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Anal og Devices for its use, nor for any infringements of patents or ot her
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
PGND
ST2 ST1 TEMP V
SELF-TEST
AMP
22nF
MECHANICAL
SENSOR
CHARGE PUMP
AND VOLTAGE
REGULATOR
22nF
DRIVE
CP1 CP2 CP3 CP4 CP5 SUMJ RATEOUT
RATIO
25kΩ
25kΩ
@ 25°C
AC
AMP
100nF
C
OUT
Figure 1.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.461.3113 ©2007 Analog Devices, Inc. All rights reserved.
VGA
180kΩ ±1%
ADXRS610
DEMOD
06520-001
ADXRS610
www.BDTIC.com/ADI
TABLE OF CONTENTS
Features.............................................................................................. 1
Theory of Operation .........................................................................9
Applications....................................................................................... 1
General Description ......................................................................... 1
Functional Block Diagram .............................................................. 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 4
Rate Sensitive Axis ....................................................................... 4
ESD Caution.................................................................................. 4
Pin Configuration and Function Descriptions............................. 5
Typical Performance Characteristics ............................................. 6
REVISION HISTORY
4/07—Revision 0: Initial Version
Setting Bandwidth.........................................................................9
Temperature Output and Calibration.........................................9
Calibrated Performance................................................................9
ADXRS610 and Supply Ratiometricity ................................... 10
Null Adjustment ......................................................................... 10
Self-Test Function ...................................................................... 10
Continuous Self-Test.................................................................. 10
Outline Dimensions....................................................................... 11
Ordering Guide .......................................................................... 11
Rev. 0 | Page 2 of 12
ADXRS610
www.BDTIC.com/ADI
SPECIFICATIONS
All minimum and maximum specifications are guaranteed. Typical specifications are not guaranteed.
T
= −40°C to +105°C, VS = AV
A
= 100 μA, ±1 g, unless otherwise noted.
I
OUT
Table 1.
Parameter Conditions
SENSITIVITY
Measurement Range
1
2
Initial and Over Temperature
Temperature Drift
3
Nonlinearity Best fit straight line 0.1 % of FS
1
NULL
Null −40°C to +105°C 2.2 2.5 2.8 V
Linear Acceleration Effect Any axis 0.1 °/sec/g
NOISE PERFORMANCE
Rate Noise Density
FREQUENCY RESPONSE
Bandwidth
4
Sensor Resonant Frequency 12 14.5 17 kHz
SELF TEST1
ST1 RATEOUT Response
ST2 RATEOUT Response ST2 pin from Logic 0 to Logic 1 250 450 650 mV
ST1 to ST2 Mismatch
5
Logic 1 Input Voltage 3.3 V
Logic 0 Input Voltage 1.7 V
Input Impedance To common 40 50 100 kΩ
TEMPERATURE SENSOR
V
at 25°C Load = 10 MΩ 2.35 2.5 2.65 V
OUT
Scale Factor
Load to V
6
S
1
Load to Common
TURN-ON TIME Power on to ±½ °/sec of final 50 ms
OUTPUT DRIVE CAPABILITY
Current Drive For rated specifications 200 μA
Capacitive Load Drive 1000 pF
POWER SUPPLY
Operating Voltage (VS) 4.75 5.00 5.25 V
Quiescent Supply Current 3.5 4.5 mA
TEMPERATURE RANGE
Specified Performance
1
Parameter is linearly ratiometric with V
2
The maximum range possible, including output swing range, initial offset, sensitivity, offset drift, and sensitivity drift at 5 V supplies.
3
From +25°C to −40°C or +25°C to 105°C.
4
Adjusted by external capacitor, C
5
Self-test mismatch is described as (ST2 + ST1)/((ST2 − ST1)/2).
6
For a change in temperature from 25°C to 26°C. V
= V
CC
= 5 V, V
DD
= AVCC, angular rate = 0°/sec, bandwidth = 80 Hz (C
RATIO
Clockwise rotation is positive output
Full-scale range over specifications range ±300 °/sec
−40°C to +105°C 5.52 6 6.48 mV/°/sec
±2 %
TA ≤ 25°C
0.01 2500 Hz
ST1 pin from Logic 0 to Logic 1 −650 −450 −250 mV
−5
@25°C, V
= 5 V 9
RATIO
−40 +105 °C
.
RATIO
. Reducing bandwidth below 0.01 Hz does not reduce noise further.
OUT
is ratiometric to V
TEMP
. See the Tem section for more details. perature Output and Calibration
RATIO
= 0.01 µF),
OUT
ADXRS610BBGZ
Min Typ Max
0.05
+5
25
25
Unit
°/sec/√Hz
%
mV/°C
kΩ
kΩ
Rev. 0 | Page 3 of 12
ADXRS610
V
/
www.BDTIC.com/ADI
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter Rating
Acceleration (Any Axis, 0.5 ms)
Unpowered 2000 g
Powered 2000 g
V
AV
DD,
CC
V
AVCC
RATIO
−0.3 V to +6.0 V
ST1, ST2 AVCC
Output Short-Circuit Duration
Indefinite
(Any Pin to Common)
Operating Temperature Range −55°C to +125°C
Storage Temperature Range −65°C to +150°C
Stresses above those listed under the Absolute Maximum
Ratings may cause permanent damage to the device. This is a
stress rating only; functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
RATE SENSITIVE AXIS
The ADXRS610 is a Z-axis rate-sensing device (also called a
yaw rate sensing device). It produces a positive going output
voltage for clockwise rotation about the axis normal to the
package top, that is, clockwise when looking down at the
package lid.
RATE
AXIS
LONGITUDI NAL
AXIS
ABCD G
A1
EF
LATERAL AXIS
Figure 2. RATEOUT Signal Increa
ESD CAUTION
RATE OUT
VCC = 5V
+
7
1
GND
/2
V
RATIO
2
RATIO
ses with Clockwise Rotation
4.75V
4.75
RATE IN
0.25V
06520-002
Drops onto hard surfaces can cause shocks of greater than
g and can exceed the absolute maximum rating of the
2000
device. Exercise care during handling to avoid damage.
Rev. 0 | Page 4 of 12
Loading...