AMX MET-13E, MET-6NE, MET-7X, MET-13X, DAS-MET6SRC Instruction Manual

...
INSTRUCTION MANUAL
METREAU® KEYPADS
MET-6N 6-BUTTON KEYPAD WITH NAVIGATION MET-7 & MET-13 KEYPADS MET-6NE 6-BUTTON ETHERNET KEYPAD WITH NAVIGATION MET-7E & MET-13E ETHERNET KEYPADS MET-7X & MET-13X ETHERNET EXPANSION KEYPADS DAS-MET6SRC 6-SOURCE AUDIO KEYPAD DAS-MET-NUM NUMERIC AUDIO KEYPAD
IMPORTANT SAFETY INSTRUCTIONS
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings. Install in accordance with the manufacturer's instructions.
8. DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. ONLY USE attachments/accessories specified by the manufacturer.
12. USE ONLY with a cart, stand, tripod, bracket, or table specified by the manu facturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.
14. REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. DO NOT expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the apparatus.
16. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from the AC receptacle.
17. Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remai n readily operable.
18. DO NOT overload wall outlets or extension cords beyond their rated capacity as this can cause electric shock or fire.
The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of suff icient magnitude to constitute a risk of electrical shock to persons.
ESD Warning: The icon to the left indicates text regarding potential danger associated with the discharge of static electricity from an outside source (such as human hands) into an integrated circuit, often resulting in damage to the circuit.
WARNING: To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture. WARNING: No naked flame sources - such as candles - should be placed on the product.
WARNING: Equipment shall be connected to a MAINS socket outlet with a protective earthing connection.
COPYRIGHT NOTICE
AMX© 2015, all rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of AMX. Copyright protection claimed extends to AMX hardware and software and includes all forms and matters copyrightable material and information now allowed by statutory or judicial law or herein after granted, including without limitation, material generated from the software programs which are displayed on the screen such as icons, screen display looks, etc. Reproduction or disassembly of embodied computer programs or algorithms is expressly prohibited.
LIABILITY NOTICE
No patent liability is assumed with respect to the use of information contained herein. While every precaution has been taken in the preparation of this publication, AMX assumes no responsibility for error or omissions. No liability is assumed for damages resulting from the use of the information contained herein. Further, this publication and features described herein are subject to change without notice.
AMX WARRANTY AND RETURN POLICY
The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.
3
Metreau Keypads Instruction Manual
ESD WARNING
To avoid ESD (Electrostatic Discharge) damage to sensitive components, make sure you are properly grounded before touching any internal materials.
When working with any equipment manufactured with electronic devices, proper ESD grounding procedures must be followed to make sure people, products, and tools are as free of static charges as possible. Grounding straps, conductive smocks, and conductive work mats are specifically designed for this purpose. These items should not be manufactured locally, since they are generally composed of highly resistive conductive materials to safely drain static discharges, without increasing an electrocution risk in the event of an accident.
Anyone performing f ield maintenance on AMX equipment should use an appropriate ESD field service kit complete with at least a dissipative work mat with a ground cord and a UL listed adjustable wrist strap with another ground cord
WARNING: Do Not Open! Risk of Electrical Shock. Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing to qualified service personnel.
Place the equipment near a main power supply ou tlet and make sure that you can easily access the power breaker switch.
WARNING: This product is intended to be operated ONLY from the voltages listed on the back panel or the recommended, or included, power supply of the product. Operation from other voltages other than those indicated may cause irreversible damage to the product and void the products warranty. The use of AC Plug Adapters is cautioned because it can allow the product to be plugged into voltages in which the product was not designed to operate. If the product is equipped with a detachable power cord, use only the type provided with your product or by your local distributor and/or retailer. If you are unsure of the correct operational voltage, please contact your local distributor and/or retailer.
FCC AND CANADA EMC COMPLIANCE INFORMATION:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Approved under the verification provision of FCC Part 15 as a Class B Digital Device. Caution: Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this
device. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
EU COMPLIANCE INFORMATION:
Eligible to bear the CE mark; Conforms to European Union Low Voltage Directive 2006/95/EC; European Union EMC Directive 2004/108/EC; European Union Restriction of Hazardous Substances Recast (RoHS2) Directive 2011/65/EU; European Union WEEE (recast) Directive 2012/19/EU; European Union Registration, Evaluation, Authorization and Restriction of Chemicals (REACH) Directive 2006/121/EC.
You may obtain a free copy of the Declaration of Conformity by visiting http://www.amx.com/techcenter/certifications.asp.
WEEE NOTICE:
This appliance is labeled in accordance with European Directive 2012/19/EU concerning waste of electrical and electronic equipment (WEEE). This label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling.
Tabl e o f Conte n ts
4
Metreau Keypads Instruction Manual
Table of Contents
Metreau® Keypads .........................................................................................10
Overview ......................................................................................................................... 10
Metreau Keypads with AxLink .............................................................................................................. 10
Metreau Audio Keypads (SWT Compatible) ......................................................................................... 11
Overview - Speaker Wire Technology (SWT)........................................................................................ 11
Metreau Keypads Device Family ........................................................................................................... 11
MET-6N and MET-6NE 6-Button Keypads with Navigation............................................. 12
MET-6N Specifications .......................................................................................................................... 12
MET-6NE Specifications ........................................................................................................................ 13
Navigation Wheel............................................................................................................ 14
Pushbuttons 7-11................................................................................................................................. 14
Navigation Wheel .................................................................................................................................. 14
MET-7, MET-7E, and MET-7X 7-Button Keypads............................................................ 14
MET-7 Specifications ............................................................................................................................ 15
MET-7E Specifications .......................................................................................................................... 15
MET-7X Specifications .......................................................................................................................... 16
MET-13, MET-13E, and MET-13X 13-Button Keypads ................................................... 16
MET-13E Specifications ........................................................................................................................ 17
MET-13X Specifications ........................................................................................................................ 18
DAS-MET-6SRC Metreau 6-Source Audio Keypad.......................................................... 18
DAS-MET-6SRC Specifications.............................................................................................................. 19
Pushbuttons 1-6 ................................................................................................................................... 19
Navigation Wheel .................................................................................................................................. 19
DAS-MET-NUM Metreau Numeric Audio Keypad............................................................ 20
DAS-MET-NUM Specifications............................................................................................................... 20
Custom Button Installation .............................................................................21
Overview ......................................................................................................................... 21
Removing Buttons .......................................................................................................... 21
Button Kits ....................................................................................................................... 22
Audio..................................................................................................................................................... 22
Residential ............................................................................................................................................ 22
Commercial........................................................................................................................................... 22
Custom Keypads and Buttons .............................................................................................................. 22
AxLink Device Addressing ...............................................................................23
Overview .......................................................................................................................... 23
Device Addressing on MET-6N Keypads.......................................................................... 23
Setting the AxLink Device Address.................................................................................. 23
Tabl e o f Conte n ts
5
Metreau Keypads Instruction Manual
Mounting and Installation ...............................................................................25
Overview .......................................................................................................................... 25
Mounting Dimensions...................................................................................................... 25
MET-6N, DAS-MET-6SRC ....................................................................................................................... 25
MET-6NE................................................................................................................................................ 26
MET-7.................................................................................................................................................... 27
MET-7E, MET-7X ................................................................................................................................... 28
MET-13, DAS-MET-NUM ........................................................................................................................ 29
MET-13E, MET-13X ............................................................................................................................... 30
Mounting Procedures ..................................................................................................... 31
Wallbox Mounting ................................................................................................................................. 31
Podium Mounting.................................................................................................................................. 31
Accent Frame ........................................................................................................................................ 31
Daisy-Chaining Keypads (Ethernet Keypads only)............................................................................... 32
Wiring and Connections ..................................................................................33
Overview .......................................................................................................................... 33
Ethernet Wiring ............................................................................................................... 33
AxLink Wiring.................................................................................................................. 34
MET-6N, MET-7, and MET-13 Rear Panel Components ........................................................................ 34
AxLink Wiring Guidelines ...................................................................................................................... 34
Preparing Captive Wires ....................................................................................................................... 34
AxLink Data and Power Connections.................................................................................................... 35
Using AxLink for Data with an Auxiliary Power Supply......................................................................... 35
Orientation of AxLink Connectors......................................................................................................... 35
AxLink Status LED ................................................................................................................................. 36
SWT Wiring ...................................................................................................................... 36
DAS-MET-6SRC and DAS-MET-7 Rear Panel Components ................................................................... 36
Cable Type ............................................................................................................................................ 36
Preparing Captive Wires ....................................................................................................................... 36
DAS-MET-6SRC - SWT Data and Power Connections............................................................................ 37
DAS-MET-NUM - Connecting to the Main DAS-MET-6SRC Keypad....................................................... 37
Tango System Integration Drawings .............................................................................. 38
Tango System Integration Drawing - Using Four-Conductor Speaker Wire ....................................... 38
Tango System Integration Drawing - Using the Audio Zone Expander ............................................... 38
SWT Special Wiring Configurations................................................................................. 39
Auxiliary Amplifier Configuration ......................................................................................................... 39
Remote Amplifier Configuration ........................................................................................................... 40
Two-Wire Configurations – Keypad for Control Only............................................................................ 40
Split Zone / Analog Volume Control ..................................................................................................... 41
Tabl e o f Conte n ts
6
Metreau Keypads Instruction Manual
Configuring Metreau Keypads with Ethernet ..................................................42
Overview ......................................................................................................................... 42
Locating the IP Address of the Keypad ................................................................................................ 42
Simulating the ID Pushbutton .............................................................................................................. 42
Toggling Between IP Addressing Modes: DHCP and Static IP ............................................................. 42
Assigning a Device ID to a Keypad ....................................................................................................... 42
Resetting the Keypad............................................................................................................................ 43
Restoring the Factory Image on the Keypad ........................................................................................ 43
Updating Firmware .........................................................................................44
Sending Firmware to Metreau Keypads (AxLink)........................................................... 44
Device Addressing on MET-6N Keypads ............................................................................................... 44
Sending Firmware to Metreau Keypads with Ethernet .................................................. 45
Programming the SWT Metreau Keypads ...................................................................... 45
Programming ..................................................................................................46
Programming the Metreau Keypads .............................................................................. 46
Button Layouts...................................................................................................................................... 46
Channels ............................................................................................................................................... 46
Port Numbers........................................................................................................................................ 46
Programming the Navigation Wheel (MET-6N & MET-6NE) ................................................................. 47
Navigation Wheel - Buttons 7-11 ......................................................................................................... 47
Navigation Wheel - Buttons 12-13 ....................................................................................................... 47
Navigation Wheel - Level Control ......................................................................................................... 47
Display Bargraph .................................................................................................................................. 47
Supported SEND_LEVELs ...................................................................................................................... 47
SEND_LEVEL........................................................................................................................................................................... 47
Supported SEND_COMMANDs............................................................................................................... 48
@BRT ..................................................................................................................................................................................... 48
@WBRT .................................................................................................................................................................................. 48
BMODE ................................................................................................................................................................................... 48
?EXPANSION.......................................................................................................................................................................... 49
LED-DIS.................................................................................................................................................................................. 49
LED-EN ................................................................................................................................................................................... 49
REBOOT.................................................................................................................................................................................. 49
SET_NDX_DESC...................................................................................................................................................................... 49
LED Feedback for 2-Position Pushbuttons ........................................................................................... 50
Terminal (Telnet) Commands ........................................................................................ 50
Establishing a Terminal Connection via Telnet .................................................................................... 50
Telnet User Name and Password.......................................................................................................... 51
Additional Notes ................................................................................................................................... 51
Setting a Telnet User Name and Password .......................................................................................... 51
Telnet Commands .......................................................................................................... 51
? or Help................................................................................................................................................................................. 51
DEVICE STATUS ..................................................................................................................................................................... 51
EXIT ....................................................................................................................................................................................... 51
FACTORYFWIMAGE................................................................................................................................................................ 51
GET CONFIG............................................................................................................................................................................ 52
Tabl e o f Conte n ts
7
Metreau Keypads Instruction Manual
GET CONNECTION................................................................................................................................................................... 52
GET DEVICE............................................................................................................................................................................. 52
GET DNS .................................................................................................................................................................................. 52
GET ETHERNET MODE ............................................................................................................................................................. 52
GET FRIENDLY <name>.......................................................................................................................................................... 52
GET IP ..................................................................................................................................................................................... 53
GET LOCATION........................................................................................................................................................................ 53
GET SN .................................................................................................................................................................................... 53
INFO........................................................................................................................................................................................ 53
MSG [ON|OFF] ......................................................................................................................................................................... 53
NDP UNBIND ........................................................................................................................................................................... 53
PING [ADDRESS]..................................................................................................................................................................... 53
REBOOT................................................................................................................................................................................... 53
RENEW DHCP .......................................................................................................................................................................... 53
RESET FACTORY...................................................................................................................................................................... 53
SET CONNECTION ................................................................................................................................................................... 53
SET DEVICE ............................................................................................................................................................................ 54
SET DNS ................................................................................................................................................................................. 54
SET ETHERNET MODE............................................................................................................................................................. 54
SET FRIENDLY ........................................................................................................................................................................ 54
SET IP ..................................................................................................................................................................................... 55
SET LOCATION ........................................................................................................................................................................ 55
SET TELNET PORT ................................................................................................................................................................... 55
SET TELNET USERNAME.......................................................................................................................................................... 55
SET TELNET PASSWORD ......................................................................................................................................................... 55
SHOW CONNECTION LOG........................................................................................................................................................ 55
SHOW CONNECTION STATS.................................................................................................................................................... 55
Notes on Specific Telnet Clients...................................................................................... 56
Windows Client Programs .................................................................................................................... 56
Linux Telnet Client ................................................................................................................................ 56
Enabling/Disabling Telnet on the Keypad....................................................................... 56
SHOW LOG............................................................................................................................................................................... 56
Basic Keypad Functions - DAS-MET-6SRC ......................................................57
Overview ......................................................................................................................... 57
DAS-MET-6SRC - Listening to a CD or DVD .................................................................... 57
Selecting the Source for Playback........................................................................................................ 57
Changing Tracks ................................................................................................................................... 57
Pausing Playback.................................................................................................................................. 57
Listening to an iPod .............................................................................................................................. 57
Listening to the Radio ........................................................................................................................... 58
Adjusting the Volume ........................................................................................................................... 58
DAS-MET-6SRC - Audio Adjustment Mode ..................................................................... 58
Adjusting Bass Level For a Room/Zone................................................................................................ 59
Adjusting Treble Level For a Room/Zone ............................................................................................. 59
Adjusting Balance For a Room/Zone.................................................................................................... 60
Adjusting SRS Settings For a Room/Zone ............................................................................................ 60
Turning SRS Off..................................................................................................................................... 60
DAS-MET-6SRC - Privacy Mode Off/On........................................................................... 61
Turning Off Privacy Mode ..................................................................................................................... 61
Working with Sources .................................................................................................... 61
DAS-MET-6SRC - Zone Control (On/Off) ......................................................................... 62
Turning a Single Zone On/Off ............................................................................................................... 62
Tabl e o f Conte n ts
8
Metreau Keypads Instruction Manual
Turning On a Source in All Zones.......................................................................................................... 62
Turning Off/On a Source in All Zones .................................................................................................. 62
Turning Off All Zones (System OFF) ..................................................................................................... 63
DAS-MET-6SRC - Zone Control (Dynamic Pause)............................................................ 63
Single Zone Listening To Source .......................................................................................................... 63
Multiple Zones Listening To The Same Source..................................................................................... 64
DAS-MET-6SRC - Using the Navigation Wheel ............................................................... 64
Using the Navigation Wheel with the Internal AM/FM Tuner............................................................... 64
Using the Navigation Wheel with the Internal SIRIUS Tuner .............................................................. 64
Using the Navigation Wheel with a CD Player/Changer....................................................................... 64
Using the Navigation Wheel with a DVD Player/Changer..................................................................... 65
Using the Navigation Wheel with a Satellite Radio/Video Box............................................................. 65
Using the Navigation Wheel with an Audio Server ............................................................................... 65
Using the Navigation Wheel with an External Tuner ............................................................................ 66
Using the Navigation Wheel with Other Sources.................................................................................. 66
Advanced Functions - DAS-MET-6SRC ............................................................67
Overview ......................................................................................................................... 67
Direct Access .................................................................................................................. 67
On-Board Tuner - Direct Selection of a Radio Station .......................................................................... 67
CD Player - Direct Selection of a Disk and Track................................................................................... 67
CD Player - Direct Selection of a Track on the Current Disk ................................................................. 68
Cable and Satellite - Direct Selection of a Channel .............................................................................. 68
Working with Presets ...................................................................................................... 69
Creating a Preset .................................................................................................................................. 69
Recalling a Preset ................................................................................................................................ 69
Clearing All Presets .............................................................................................................................. 70
Working with Favorites................................................................................................... 70
Creating a Favorite for a Specific Source ............................................................................................. 70
Clearing Favorites for All Sources in a Specific Zone ........................................................................... 71
Working with Zone Grouping.......................................................................................... 71
Adding a Zone to a Group ..................................................................................................................... 71
Grouping All Zones ............................................................................................................................... 72
Un-Grouping All Zones ......................................................................................................................... 72
Grouping Volume Control ..................................................................................................................... 72
Working with Alarms ...................................................................................................... 73
Setting the System Clock on the Tango Audio Controller .................................................................... 73
Setting an Alarm in a Zone.................................................................................................................... 73
Clearing the Alarm for a Specific Zone ................................................................................................ 74
Clearing All Alarms for All Zones ......................................................................................................... 74
Keypad Lockout .............................................................................................................. 75
Locking a Keypad .................................................................................................................................. 75
Unlocking a Keypad .............................................................................................................................. 75
Tabl e o f Conte n ts
9
Metreau Keypads Instruction Manual
Unlocking All Keypads .......................................................................................................................... 76
Using the NetLinx Module ...............................................................................78
Overview ......................................................................................................................... 78
Main Page (Initial View) ................................................................................................. 78
Main Pages ..................................................................................................................... 79
Location/Device Pages ......................................................................................................................... 79
Zone Options......................................................................................................................................... 80
Change Source ..................................................................................................................................... 80
Device Control Pages...................................................................................................... 81
Internal Tuner....................................................................................................................................... 81
Internal Sirius ....................................................................................................................................... 82
DVD........................................................................................................................................................ 83
CD.......................................................................................................................................................... 84
Audio Server ......................................................................................................................................... 85
Satellite ................................................................................................................................................. 86
External Tuner ...................................................................................................................................... 87
Other ..................................................................................................................................................... 88
Setup Pages..................................................................................................................... 89
Setup - Zones ........................................................................................................................................ 89
Setup - Alarms ...................................................................................................................................... 90
Adding an Alarm ................................................................................................................................... 90
Removing an Alarm............................................................................................................................... 92
SWT Troubleshooting ......................................................................................93
Overview .......................................................................................................................... 93
Power Connections ......................................................................................................... 93
Zone Connection Problems ............................................................................................ 94
Dead Zones ........................................................................................................................................... 94
LED Does Not light................................................................................................................................. 94
Source Connections.............................................................................................................................. 94
No Keypad Activity .......................................................................................................... 95
Keypad Lights, No Sound ................................................................................................ 95
10
Metreau Keypads Instruction Manual
Metreau® Keypads
Metreau keypads (Ethernet)
MET-6NE
MET-7E MET-13E
Metreau keypads (AxLink)
MET-6N
MET-7 MET-13
Overview
Metreau keypads are a convenient, versatile, cost-effective option for achieving effortless control of virtually anything through a
®
NetLinx NetLinx Integrated Controllers (all keypads) and Tango Distributed Audio Systems (Audio Keypads only).
There are three basic variations within the Metreau device family:
Metreau Keypads with Ethernet
The MET-6NE, MET-7E and MET-13E keypads connect to a NetLinx control system via category cable. These keypads can be used as individual keypads or in conjunction with the MET-7X or MET-13X Metreau Ethernet Expansion Keypads.
control system. Metreau keypads offer easy installation within decora-style wall plates and sleek styling that complements
Metreau® Keypads
Metreau Keypads with Ethernet
FIG. 1
Metreau Keypads with AxLink
The MET-6N, MET-7 and MET-13 keypads are AxLink-compatible, for use with NetLinx control systems (FIG. 2).
FIG. 2 Metreau Keypads with AxLink
Metreau® Keypads
11
Metreau Keypads Instruction Manual
DAS-MET-6SRC
DAS-MET-NUM
Metreau Audio keypads (SWT)
Metreau Audio Keypads (SWT Compatible)
The DAS-MET-6SRC and DAS-MET-NUM are SWT-compatible, for use with Matrix Audio distribution systems, via Speaker Wire Technology (SWT). Metreau Audio keypads are compatible with all Matrix products including Tango and Mi Series Audio Controllers as well as XA Carbon Series Amplifiers (FIG. 3).
FIG. 3
Metreau Audio keypads
Note: In terms of SWT functionality, the Metreau Audio keypads (DAS-MET-6SRC & DAS-MET-NUM) are a close match to previous versions of Matrix KP and NUM keypads.
Overview - Speaker Wire Technology (SWT)
Speaker Wire Technology (SWT) allows both data and audio signals to travel over the same four conductor wire. This remarkable technology removes the need for control wire since the control and audio signals are shared on the same wire. The reliability and simplicity of this system has been proven for years. AMX Matrix Audio is the only company that offers a “retrofit solution”, one which allows the replacement of volume controls with AMX Matrix Audio keypads and Controllers, giving full control over the sources.
Addition ally, the versatility o f SWT also allows AMX Matrix Audio products to be connected where the control wire has been run separately from the speaker cable.
Metreau Keypads Device Family
All Metreau keypads are available in two colors: White and Black. Some older models are also available in Light Almond. The following table lists the keypads in the Metreau family, with descriptions and FG#s for each color.
Metreau Keypads Device Family
Name Description Colors/FG#s
MET-6N Metreau 6-Button Keypad with Navigation • White (FG5794-01-WH)
•Black (FG5794-01-BL)
• Light Almond (FG5794-01-LA)
MET-7 Metreau 7-Button Keypad • White (FG5794-03-WH)
•Black (FG5794-03-BL)
• Light Almond (FG5794-03-LA)
MET-13 Metreau 13-Button Keypad • White (FG5794-02-WH)
•Black (FG5794-02-BL)
• Light Almond (FG5794-02-LA)
MET-6NE Metreau 6-Button Ethernet Keypad with
Navigation
MET-7E Metreau 7-Button Ethernet Keypad • White (FG5793-03-WH)
MET-13E Metreau 13-Button Ethernet Keypad • White (FG5793-02-WH)
MET-7X Metreau 7-Button Ethernet Expansion
Keypad
MET-13X Metreau 13-Button Ethernet Expansion
Keypad
DAS-MET-6SRC Metreau 6-Source Audio Keypad • White (FG1122-01-WH)
DAS-MET-NUM Metreau Numeric Audio Keypad • White (FG1122-02-WH)
•White (FG5793-01-WH)
•Black (FG5793-01-BL)
•Black (FG5793-03-BL)
•Black (FG5793-02-BL)
•White (FG5793-13-WH)
•Black (FG5793-13-BL)
•White (FG5793-12-WH)
•Black (FG5793-12-BL)
•Black (FG1122-01-BL)
• Light Almond (FG1122-01-LA)
•Black (FG1122-02-BL)
• Light Almond (FG1122-02-LA)
Metreau® Keypads
12
Metreau Keypads Instruction Manual
IR Sensor located here
LED Levels Indicator
Navigation Wheel
6 pre-printed pushbuttons
(with blue LED indicators)
(supports AMX IR 38kHz)
1
2
3
4
5 6
109 11
7
8
CW rotation = 12 CCW rotation = 13
Center (push/release) Center (press/hold)
MET-6N and MET-6NE 6-Button Keypads with Navigation
The Metreau 6-button keypads feature source control, visual volume feedback, and a navigation wheel that adjusts volume and provides up, down, left, right and center button options. FIG. 4 displays the MET-6N. The MET-6NE differs slightly in appearance, but has the same button functionality as the MET-6N.
FIG. 4 MET-6N Metreau 6-Button keypad with Navigation (Light Almond shown)
The MET-6N is an AxLink keypad, suitable for use in NetLinx Control Systems.
MET-6N Specif ications
MET-6N Specifications
Power: 12 VDC, 75 mA
Front Panel Components:
Rear Panel Components:
Dimensions (HWD): • Keypad and Mounting Plate: 4.055" x 1.772" x 0.997" (103mm x 45mm x 25.32mm)
Weight:
Operating Environment:
Certifications: • FCC Class B
Colors: • White (FG5794-01-WH)
Optional Accessories:
• Pushbuttons - 6 tactile pushbuttons with blue LED indicators that illuminate when pressed to confirm the source/function was selected and that it is currently being used. These pre-printed buttons are field­replaceable.
• IR Sensor - Supports standard AMX IR (38 kHz only).
• LED Levels Indicator - set of 7 blue LEDs provide level feedback.
• Navigation Wheel - consists of 5 pushbuttons: 4 directional pushbu ttons (Up, Down, Right, Left), 1 center pushbutton, and bi-directional rotating wheel for channel adjustments.
• The Navigation wheel itself provides two button functions as well (rotate CW = button #12, and rotate CCW = button #13, as indicated in FIG. 5).
• DIP switch - 8 position mini DIP switch used to set the device address for the keypad on the AxLink Bus (1-255).
• AxLink connector - 4 pin 3.5mm Phoenix connector for AxLink connection to the NetLinx Master.
• Mounts into standard decora-style wall plates.
0.15 lbs. (0.068 kg)
• Operating Temperature: 32° - 104° F (0°- 40° C).
• Relative Humidity: 5% - 85%, non-condensing.
• Intended fo r indoor use only.
•CE
•IEC60950
•RoHS
•Black (FG5794-01-BL)
• Light Almond (FG5794-01-LA)
• Single Bu tton Kit (FG5794-10)
• Lutron Cairo Wallplates (available in a variety of sizes and colors)
Metreau® Keypads
13
Metreau Keypads Instruction Manual
The MET-6NE is an Ethernet keypad, suitable for use in NetLinx Control Systems.
MET-6NE Specif ications
MET-6NE Specifications
Power: • PoE: PoE (Power over Ethernet), 802.3af, class 0
• Power Connector: (1) RJ-45 Ethernet Connector, 10/100
Power Supply: POE injector or switch (external, required), conforming to the 802.3af standard including AMX’s PS-POE-AF-TC
Front Panel Components:
Rear Panel Components:
Dimensions (HWD): • Keypad and Mounting Plate: 4" x 1 3/4" x 1" (10.3 cm x 4.5 cm x 2.5 cm)
Weight: 0.17 lbs. (0.07 kg)
Operating Environment:
Certifications: • FCC Class B
Colors: • White (FG5793-01-WH)
Optional Accessories:
(FG423-83), not included
• Pushbuttons - 6 tactile pushbuttons with blue LED indicators that illuminate when pressed to confirm the source/function was selected and that it is currently being used. These pre-printed buttons are field­replaceable.
• IR Sensor - Supports standard AMX IR (38 kHz only).
• LED Levels Indicator - set of 7 blue LEDs provide level feedback.
• Navigation Wheel - consists of 5 pushbuttons: 4 directional pushbu ttons (Up, Down, Right, Left), 1 center pushbutton, and bi-directional rotating wheel for channel adjustments.
• The Navigation wheel itself provides two button functions as well (rotate CW = button #12, and rotate CCW = button #13, as indicated in FIG. 5).
• (1) RJ-45 Ethernet connector, 10/100
• (1) 10-pin IDC-type connector for connection to expansion keypads
• Mounts into standard decora-style wall plates.
• Operating Temperature: 32° - 104° F (0°- 40° C).
• Relative Humidity: 5% - 85%, non-condensing.
• Intended fo r indoor use only.
•CE
•IEC60950
•RoHS
•Black (FG5793-01-BL)
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• ALD-CW-1, 1-Gang Claro Wallplate (FG2605-81-BL/FG2605-81-WH)
• ALD-CW-2, 2-Gang Claro Wallplate (FG2605-82-BL/FG2605-82-WH)
• ALD-CW-3, 3-Gang Claro Wallplate (FG2605-83-BL/FG2605-83-WH)
Can be used in conjunction with up to two Metreau Ethernet Expansion Keypads:
• MET-13X-WH, Metreau 13-Button Expansion Keypad (FG5793-12-WH)
• MET-13X-BL, Metreau 13-Button Expansion Keypad (FG5793-12-BL)
• MET-7X-WH, Metreau 7-Button Expansion Keypad (FG5793-13-WH)
• MET-7X-BL, Metreau 7-Button Expansion Keypad (FG5793-13-BL)
Metreau® Keypads
14
Metreau Keypads Instruction Manual
Rotate clockwise
Directional pushbutton UP
Rotate counter-clockwise
= button #13 = button #12
Center pushbutton
7
10
8
9
11
Directional pushbutton DOWN
Directional pushbutton
RIGHT
Directional pushbutton
LEFT
7 pre-printed pushbuttons
(with blue LED indicators)
Two-position button
Navigation Wheel
FIG. 5 shows the button layout of the Navigation Wheel:
FIG. 5
Navigation Wheel - button layout (MET-6N displayed)
Pushbuttons 7-11
The top, bottom, left, right and center points on the Navigation Wheel are pushbuttons #7, #8, #9, #10 and #11, and can be programmed like any other button.
Navigation Wheel
The Navigation Wheel itself can be rotated clockwise and counterclockwise, and is intended to provide level control (for example volume or li ghting levels).
When rotated clockwise, the Navigation Wheel provides a channel event on button #12. When rotated counter-clockwise, the Navigation Wheel provides a channel event on button #13. The light on the Navigation Wheel can be illuminated by activating channel #11 (MET-6N only).
MET-7, MET-7E, and MET-7X 7-Button Keypads
The Metreau 7-button keypads offer 7 double-width buttons that can be used as in individual keypad or in conjunction with the 6­and 13-button Metreau keypads. FIG. 6 displays the MET-7. The MET-7E differs slightly in appearance, but has the same button functionality as the MET-7.
FIG. 6 MET-7 Metreau 7-Button keypad (Light Almond shown)
15
Metreau Keypads Instruction Manual
The MET-7 is an AxLink keypad, suitable for use in NetLinx Control Systems.
MET-7 Specif ications
MET-7 Specifications
Power: 12 VDC, 30 mA
Front Panel Components:
Rear Panel Components:
Dimensions (HWD): • Keypad and Mounting Plate: 4.055" x 1.772" x 0.818" (103mm x 45mm x 207mm)
Weight: 0.15 lbs. (0.068 kg)
Operating Environment:
Certifications: • FCC Class B
Colors: • White (FG5794-03-WH)
Optional Accessories:
Pushbuttons - 7 tactile pushbuttons with blue LED indicators that illuminate when pressed to confirm the source/ function was selected and that it is currently being used. These pre-printed buttons are field-replaceable.
The bottom button functions as 2 buttons - there are 2 positions (left and right) that allow the user to control channel/levels (up/down).
• DIP switch - 8-position mini DIP switch used to set the device address for the keypad on the AxLink Bus (1-255).
• AxLink connector - 4-pin 3.5mm Phoenix connector for AxLink connection to the NetLinx Master.
• Mounts into standard decora-style wall plates.
• Operating Temperature: 32° - 104° F (0°- 40° C).
• Relative Humidity: 5% - 85%, non-condensing.
• Intended fo r indoor use only.
•IEC60950
•CE
•Black (FG5794-03-BL)
• Light Almond (FG5794-03-LA)
• Single Bu tton Kit (FG5794-10)
• Double Button Kit (FG5794-11)
• Lutron Cairo Wallplates (available in a variety of sizes and colors)
•RoHS
Metreau® Keypads
MET-7E Specif ications
The MET-7E is an Ethernet keypad, suitable for use in NetLinx Control Systems.
MET-7E Specifications
Power: • PoE: PoE (Power over Ethernet), 802.3af, class 0
• Power Connector: (1) RJ-45 Ethernet Connector, 10/100
Power Supply: POE injector or switch (external, required), conforming to the 802.3af standard including AMX’s PS-POE-AF-TC
Front Panel Components:
Rear Panel Components:
Dimensions (HWD): • Keypad and Mounting Plate: 4" x 1 3/4" x 1" (10.3 cm x 4.5 cm x 2.5 cm)
Weight:
Operating Environment:
Certifications: • FCC Class B
Colors: • White (FG5793-01-WH)
Optional Accessories:
(FG423-83), not included
• Pushbuttons - 7 tactile pushbuttons with blue LED indicators that illuminate when pressed to confirm the source/function was selected and that it is currently being used. These pre-printed buttons are field­replaceable.
• (1) RJ-45 Ethernet connector, 10/100
• (1) 10-pin IDC-type connector for connection to expansion keypads
• Mounts into standard decora-style wall plates.
0.18 lbs. (0.08 kg)
• Operating Temperature: 32° - 104° F (0°- 40° C).
• Relative Humidity: 5% - 85%, non-condensing.
• Intended fo r indoor use only.
•IEC60950
•CE
•Black (FG5793-01-BL)
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• ALD-CW-1, 1-Gang Claro Wallplate (FG2605-81-BL/FG2605-81-WH)
• ALD-CW-2, 2-Gang Claro Wallplate (FG2605-82-BL/FG2605-82-WH)
• ALD-CW-3, 3-Gang Claro Wallplate (FG2605-83-BL/FG2605-83-WH)
Can be used in conjunction with up to two Metreau Ethernet Expansion Keypads:
• MET-13X-WH, Metreau 13-Button Expansion Keypad (FG5793-12-WH)
• MET-13X-BL, Metreau 13-Button Expansion Keypad (FG5793-12-BL)
• MET-7X-WH, Metreau 7-Button Expansion Keypad (FG5793-13-WH)
• MET-7X-BL, Metreau 7-Button Expansion Keypad (FG5793-13-BL)
•RoHS
Metreau® Keypads
16
Metreau Keypads Instruction Manual
13 pre-printed pushbuttons
(with blue LED indicators)
Two-position button
MET-7X Specif ications
The MET-7X is an Ethernet Expansion keypad, suitable for use in NetLinx Control Systems.
MET-7X Specifications
Power: PoE: The Expansion Keypad receives power from the Metreau Ethernet Keypad it is connected to (options include
Front Panel Components:
Rear Panel Components:
Dimensions (HWD): • Keypad and Mounting Plate: 4" x 1 3/4" x 1" (10.3 cm x 4.5 cm x 2.5 cm)
Weight: 0.14 lbs. (0.06 kg)
Operating Environment:
Certifications: • FCC Class B
Colors: • White (FG5793-01-WH)
Optional Accessories:
MET-6NE, MET-7E and MET-13E) via the ribbon cable. See the power options for the connected Ethernet keypad for PoE specifications
(7) tactile pushbuttons with blue LED indicators that illuminate when pressed to confirm the source/function was selected and that it is currently being used. These pre-printed buttons are field-replaceable.
• (1) 10-pin IDC-type connector for connection to additional expansion keypads
• (1) ribbon cable for connection to Ethernet keypads
• Mounts into standard decora-style wall plates.
• Operating Temperature: 32° - 104° F (0°- 40° C).
• Relative Humidity: 5% - 85%, non-condensing.
• Intended fo r indoor use only.
•IEC60950
•CE
•Black (FG5793-01-BL)
• ALD-CW-1, 1-Gang Claro Wallplate (FG2605-81-BL/FG2605-81-WH)
• ALD-CW-2, 2-Gang Claro Wallplate (FG2605-82-BL/FG2605-82-WH)
• ALD-CW-3, 3-Gang Claro Wallplate (FG2605-83-BL/FG2605-83-WH)
•RoHS
MET-13, MET-13E, and MET-13X 13-Button Keypads
The Metreau 13-button keypads offer 13 buttons (12 single-width and 1 double-width) and can be used as in individual keypad or in conjunction with the 6- and 7-button Metreau keypads. FIG. 7 displays the MET-13. The MET-13E differs slightly in appearance, but has the same button functionality as the MET-13.
FIG. 7 MET-13 Metreau 13-Button keypad (Light Almond shown)
17
Metreau Keypads Instruction Manual
The MET-13 is an AxLink keypad, suitable for use in NetLinx Control Systems.
MET-13 Specifications
MET-13 Specifications
Power: 12 VDC, 30 mA
Front Panel Components:
Rear Panel Components:
Dimensions (HWD): • Keypad and Mounting Plate: 4.055" x 1.772" x 0.818"
Weight: 0.15 lbs. (0.068 kg)
Operating Environment:
Certifications: • FCC Class B
Colors: • White (FG5794-02-WH)
Optional Accessories:
Pushbu ttons - 13 tactile pushbu ttons with blue LED indicators that illuminate when pressed to conf irm the source/ function was selected and that it is currently being used (12 single-width, 1 double-width). These pre-printed buttons are field-replaceable.
The bottom button functions as 2 buttons - there are 2 positions (left and right) that allow the user to control channels (up/down).
• DIP switch - 8-position mini DIP switch used to set the device address for the keypad on the AxLink Bus (1-255).
• AxLink connector - 4-pin 3.5mm Phoenix connector for AxLink connection to the NetLinx Master.
(103mm x 45mm x 207mm)
• Mounts into standard decora-style wall plates.
• Operating Temperature: 32° - 104° F (0°- 40° C).
• Relative Humidity: 5% - 85%, non-condensing.
• Intended fo r indoor use only.
•CE
•Black (FG5794-02-BL)
• Light Almond (FG5794-02-LA)
• Single Bu tton Kit (FG5794-10)
• Double Button Kit (FG5794-11)
• Lutron Cairo Wallplates (available in a variety of sizes and colors)
Metreau® Keypads
•IEC60950
•RoHS
MET-13E Specif ications
The MET-13E is an Ethernet keypad, suitable for use in NetLinx Control Systems.
MET-13E Specifications
Power: • PoE: PoE (Power over Ethernet), 802.3af, class 0
• Power Connector: (1) RJ-45 Ethernet Connector, 10/100
Power Supply: POE injector or switch (external, required), conforming to the 802.3af standard including AMX’s PS-POE-AF-TC
Front Panel Components:
Rear Panel Components:
Dimensions (HWD): • Keypad and Mounting Plate: 4" x 1 3/4" x 1" (10.3 cm x 4.5 cm x 2.5 cm)
Weight:
Operating Environment:
Certifications: • FCC Class B
Colors: • White (FG5793-01-WH)
Optional Accessories:
(FG423-83), not included
(13) tactile pushbuttons with blue LED indicators that illuminate when pressed to conf irm the source/function was selected and that it is currently being used. These pre-printed buttons are field-replaceable.
• (1) RJ-45 Ethernet connector, 10/100
• (1) 10-pin IDC-type connector for connection to expansion keypads
• Mounts into standard decora-style wall plates.
0.18 lbs. (0.08 kg)
• Operating Temperature: 32° - 104° F (0°- 40° C).
• Relative Humidity: 5% - 85%, non-condensing.
• Intended fo r indoor use only.
•IEC60950
•CE
•Black (FG5793-01-BL)
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• ALD-CW-1, 1-Gang Claro Wallplate (FG2605-81-BL/FG2605-81-WH)
• ALD-CW-2, 2-Gang Claro Wallplate (FG2605-82-BL/FG2605-82-WH)
• ALD-CW-3, 3-Gang Claro Wallplate (FG2605-83-BL/FG2605-83-WH)
Can be used in conjunction with up to two Metreau Ethernet Expansion Keypads:
• MET-13X-WH, Metreau 13-Button Expansion Keypad (FG5793-12-WH)
• MET-13X-BL, Metreau 13-Button Expansion Keypad (FG5793-12-BL)
• MET-7X-WH, Metreau 7-Button Expansion Keypad (FG5793-13-WH)
• MET-7X-BL, Metreau 7-Button Expansion Keypad (FG5793-13-BL)
•RoHS
Metreau® Keypads
18
Metreau Keypads Instruction Manual
IR Sensor located here
Navigation Wheel
6 pre-printed pushbuttons
(with blue LED indicators)
Volume Level Indicator LEDs
MET-13X Specif ications
The MET-13X is an Ethernet Expansion keypad, suitable for use in NetLinx Control Systems.
MET-13X Specifications
Power: PoE: The Expansion Keypad receives power from the Metreau Ethernet Keypad it is connected to (options include
Front Panel Components:
Rear Panel Components:
Dimensions (HWD): • Keypad and Mounting Plate: 4" x 1 3/4" x 1" (10.3 cm x 4.5 cm x 2.5 cm)
Weight: 0.14 lbs. (0.06 kg)
Operating Environment:
Certifications: • FCC Class B
Colors: • White (FG5793-01-WH)
Optional Accessories:
MET-6NE, MET-7E and MET-13E) via the ribbon cable. See the power options for the connected Ethernet keypad for PoE specifications
(13) tactile pushbuttons with blue LED indicators that illuminate when pressed to conf irm the source/function was selected and that it is currently being used. These pre-printed buttons are field-replaceable.
• (1) 10-pin IDC-type connector for connection to additional expansion keypads
• (1) ribbon cable for connection to Ethernet keypads
• Mounts into standard decora-style wall plates.
• Operating Temperature: 32° - 104° F (0°- 40° C).
• Relative Humidity: 5% - 85%, non-condensing.
• Intended fo r indoor use only.
•IEC60950
•CE
•Black (FG5793-01-BL)
• ALD-CW-1, 1-Gang Claro Wallplate (FG2605-81-BL/FG2605-81-WH)
• ALD-CW-2, 2-Gang Claro Wallplate (FG2605-82-BL/FG2605-82-WH)
• ALD-CW-3, 3-Gang Claro Wallplate (FG2605-83-BL/FG2605-83-WH)
•RoHS
DAS-MET-6SRC Metreau 6-Source Audio Keypad
The DAS-MET-6SRC 6-button keypad (FIG. 8) features source control, visual volume feedback and a navigation wheel that adjusts volume and provides up, down, left, right and center button options (see the Basic Keypad Functions - DAS-MET-6SRC section on page 57 for information).
FIG. 8 DAS-MET-6SRC Metreau 6-Source Audio keypad (Light Almond shown)
19
Metreau Keypads Instruction Manual
The DAS-MET-6SRC is a SWT keypad, suitable for use in Matrix Distributed Audio Systems.
Rotate wheel clockwise to adjust Volume Up
Rotate wheel
counter-clockwise to
adjust Volume Down
Top center pushbutton = Nav UP
Bottom center pushbutton = Nav DOWN
Right center pushbutton = Nav RIGHT
Left center
pushbu tton =
Nav LEFT
Center pushbutton = Nav Center
DAS-MET-6SRC Specif ications
DAS-MET-6SRC Specifications
Power: 12 VDC, 125 mA
Front Panel Components:
Rear Panel Components:
Dimensions (HWD): • Keypad and Mounting Plate: 4.055" x 1.772" x 0.997"
Weight: 0.15 lbs. (0.068 kg)
Operating Environment:
Certifications: • FCC Class B
Colors: • White (FG1122-01-WH)
Optional Accessories:
• Pushbuttons - 6 tactile pushbuttons with blue LED indicators that illuminate when the source is selected, and stay lit until the source is turned off. These pre-printed buttons are field-replaceable.
• IR Sensor - Works specifically with the MIO-R1-AUDIO remote controller (38 kHz only).
• LED Levels Indicator - set of 7 blue LEDs provide volume level feedback.
• Navigation Wheel - consists of 5 pushbuttons: 4 directional pushbu ttons (Up, Down, Right, Left), 1 center pushbutton, and bi-directional rotating wheel for volume adjustments.
Note that the center pushbutton is dual-purpose: a push/release provides one function, while a press/hold provides another.
Wiring connection - Two 4-pin SWT connectors that provide connection from the Matrix Audio Controller, and to the speakers.
(103mm x 45mm x 25.32mm)
• Mounts into standard decora-style wall plates.
• Operating Temperature: 32° - 104° F (0°- 40° C).
• Relative Humidity: 5% - 85%, non-condensing.
• Intended fo r indoor use only.
•IEC60950
•CE
•Black (FG1122-01-BL)
• Light Almond (FG1122-01-LA)
• Single Bu tton Kit (FG5794-10)
• Lutron Cairo Wallplates (available in a variety of sizes and colors)
•RoHS
Metreau® Keypads
Pushbuttons 1-6
The top, bottom, left and right points on the Navigation Wheel are used for source control and can be programmed to provide any source functionality by learning the applicable IR code.
The center pushbutton is dual-purpose: a push/release on this button provides one function, while a press/hold provides another. The center pushbutton are also used for source control and can be programmed to provide any source functionality (again, by learning the applicable IR code).
Navigation Wheel
FIG. 9 shows the button layout of the Navigation Wheel:
FIG. 9 Navigation Wheel - button layout
The Navigation Wheel can be rotated bi-directionally, and provides volume level control:
Clockwise rotation increases the volume level, counter-clockwise rotation decreases the volume level. The range for volume is 0 - 70.
Metreau® Keypads
20
Metreau Keypads Instruction Manual
12 pre-printed pushbuttons
ENTER button
(with LED to
provide feedback)
DAS-MET-NUM Metreau Numeric Audio Keypad
The DAS-MET-NUM Metreau numeric keypad (FIG. 10) connects to the Main DAS-MET-6SRC keypad via a 14-pin connector. Used in conjunction with the DAS-MET-6SRC Metreau keypad, it provides direct numeric access, setting & recalling presets, and access to advanced functionality such as grouping, Setting Favorites, Alarm, and Keypad lockout functionality (see the Advanced Functions - DAS-MET-6SRC section on page 67 for information).
FIG. 10 DAS-MET-NUM Metreau Numeric Audio keypad (White shown)
The DAS-MET-NUM is a SWT keypad, suitable for use in Matrix Distributed Audio Systems.
DAS-MET-NUM Specifications
DAS-MET-NUM Specif ications
Power: 12 VDC, 125 mA
Front Panel Components:
Rear Panel Components:
Dimensions (HWD): • Keypad and Mounting Plate: 4.055" x 1.772" x 0.818"
Weight:
Operating Environment:
Certifications: • FCC Class B
Colors: • White (FG1122-02-WH)
Optional Accessories:
Pushbu ttons - 13 tactile pushbuttons.
Wiring connection - One 14-pin connector that provides connection to the main 6 Source Metreau Keypad (DAS­MET-6SRC).
(103mm x 45mm x 207mm)
• Mounts into standard decora-style wall plates.
0.15 lbs. (0.068 kg)
• Operating Temperature: 32° - 104° F (0°- 40° C).
• Relative Humidity: 5% - 85%, non-condensing.
• Intended fo r indoor use only.
•IEC60950
•CE
•Black (FG1122-02-BL)
• Light Almond (FG1122-02-LA)
• Single Bu tton Kit (FG5794-10)
• Double Button Kit (FG5794-11)
• Lutron Cairo Wallplates (available in a variety of sizes and colors)
•RoHS
21
Metreau Keypads Instruction Manual
Custom Button Installation
Plastic Faceplate
Metal Mounting Plate
Circuit board
Plastic tab
Plastic tab
Overview
With the exception of the DAS-MET-NUM, all Metreau keypads feature field-replaceable pre-printed buttons. This section describes removing the original set of buttons and replacing them with custom buttons.
Removing Buttons
The easiest way to remove and replace buttons on the Metreau keypads is to place the keypad assembly (FIG. 11) face-down on a flat level surface, so that the buttons stay in position until you are ready to remove them.
IMPORTANT: Disconnect the power supply and all wiring connections before removing/replacing buttons on the Metreau keypads.
IMPORTANT: Before touching the device, discharge the static electricity from your body by touching a grounded metal object.
The Faceplate is attached to the Mounting Plate via four plastic tabs (two on each side of the Faceplate, as shown in FIG. 11). It is not necessary to remove the plastic faceplate from the Mounting Plate in order to replace buttons.
1. The faceplate is attached to the mounting plate via four plastic tabs (two on each side o f the faceplate, see FIG. 11). To remove the faceplate, gently pry it from either side.
2. Gently lift each button off of their mounting posts on the circuit board.
3. Select the location of the custom buttons and gently snap them into place on the Circuit Board. Be sure to note the orientation of the LED window on each button, to avoid accidentally mounting them upside down.
4. Reattach the plastic faceplate.
Custom Button Installation
FIG. 11
Keypad assembly
Custom Button Installation
22
Metreau Keypads Instruction Manual
Button Kits
Three different button kits, which accommodate most installations, are available for Metreau keypads:
Audio
SIRIUS, XM, IPOD, MP3, CD2, AUX2, DVD2, PC, FM.
Residential
LIGHTS, FAN, SHADES, HVAC+, HVAC -, UP, DOWN, TV.
Commercial
DISP, PROJ, VC, AC, HVAC, LIGHTS, SCREEN.
Custom Keypads and Buttons
If a requested keypad needs functions not offered in the standard Button Kits, a custom keypad may be built with the AMX Metreau Keypad Preview (FIG. 12), available at www.amx.com. This tool allows custom arrangement of default or custom button arrangements, creation of custom button text, previews of keypad type and color, and printouts of f inal keypad layouts and parts lists.
FIG. 12
Metreau Keypad Preview
23
Metreau Keypads Instruction Manual
AxLink Device Addressing
MET-6N MET-7
DIP Switch
DIP Switch
DIP Switch
MET-13
Overview
Metreau Keypads with AxLink used in NetLinx applications require a unique numeric AxLink device address of 1-255. Consider specifying the device address for each keypad before final installation.
NOTE: AxLink device addressing applies only to the MET-6N, MET-7, and MET-13 keypads. Metreau Audio Keypads (DAS-MET-6SRC and DAS-MET-13) do not require device addressing.
Device Addressing on MET-6N Keypads
The MET-6N uses two AxLink devices addresses - one for the keypad itself, and a second one for the IR Receiver. The device address of the IR Receiver is auto-assigned to be one number higher than the device address of the keypad itself
(to which the firmware is uploaded).
The MET-6N will appear as two devices in the Devices frame, because it’s built-in IR Receiver is recognized as a separate
online device.
Firmware is uploaded to the device address of the keypad (not the IR Receiver).
For example, if the MET-6N is set to device add ress 127, then the IR Receiver on that MET-6N will appear as device number
128. Firmware must be sent to the keypad, not the IR Receiver (in this example, device 127).
Setting the AxLink Device Address
AxLink-enabled Metreau keypads (MET-6N, MET-7 and MET-13) use an 8-position mini-DIP switch to specify a unique device address for each keypad in a NetLinx Control System (see FIG. 13).
AxLink Device Addressing
FIG. 13
NOTE: Before touching the device, discharge the static electricity from your body by touching a grounded metal object.
1. If connected, disconnect the power supply.
2. Locate the 8-position mini-DIP switch on the rear panel.
3. Set the DIP switch according to the values shown below.
DIP Switch and SWT Jumper locations
Switch 12345 6 7 8
Value 1 2 4 8 16 32 64 128
The device number is set by the total value of DIP switch positions that are in the ON position. Note that the ON position is indicated on the DIP Switch.
24
Metreau Keypads Instruction Manual
As an example, the DIP switch in FIG. 14 defines AXlink device number 129 (1+128=129).
AxLink Device Addressing
FIG. 14
8-position mini-DIP Switch
If you later change the device number, remove and reconnect the power connector to enter the new device number into memory.
NOTE: AMX has created the "Dip Switch2" software application to assist in calculating dip switch position values. Download the (free) program Dip Switch2 from www.amx.com.
25
Metreau Keypads Instruction Manual
Mounting and Installation
Overview
Metreau keypads are designed to install into standard U.S. decora-style wall plates and boxes (wallboxes not included).
IMPORTANT: Before touching the device, discharge the static electricity from your body by touching a grounded metal object.
Mounting Dimensions
MET-6N, DAS-MET-6SRC
FIG. 15 provides detailed dimensions for the MET-6N and DAS-MET-6SRC keypads.
Mounting and Installation
FIG. 15
MET-6N and DAS-MET-6SRC Mounting Dimensions
26
Metreau Keypads Instruction Manual
MET-6NE
FIG. 16 provides detailed dimensions for the MET-6NE keypad.
Mounting and Installation
FIG. 16
MET-6NE Mounting Dimensions
27
Metreau Keypads Instruction Manual
MET-7
FIG. 17 provides detailed dimensions for the MET-7 keypads.
Mounting and Installation
FIG. 17
MET-7 Mounting Dimensions
28
Metreau Keypads Instruction Manual
MET-7E, MET-7X
MET-7X
MET-7E
FIG. 18 provides detailed dimensions for the MET-7E and MET-7X keypads.
Mounting and Installation
FIG. 18
MET-7E and MET-7X Mounting Dimensions
29
Metreau Keypads Instruction Manual
MET-13, DAS-MET-NUM
FIG. 19 provides detailed dimensions for the MET-13 and DAS-MET-NUM keypads.
Mounting and Installation
FIG. 19
MET-13 and DAS-MET-NUM Mounting Dimensions
Loading...
+ 67 hidden pages