Page 1
DATA SHEET
DXLinkTM Multi-Format Wallplate
Transmitters
AVB-WP-TX-MULTI-DXLINK (FG1010-320-BL, FG1010-320-WH)
Overview
The DXLink Multi-Format Wallplate Transmitter sends analog or digital video
including HDMI/HDCP, along with embedded audio or supplemental analog audio
up to 100 meters to an Enova DGX Matrix Switcher, compatible Enova DVX All-InOne Presentation Switcher, or directly to a DXLink Receiver. It receives power from
the Enova DGX or Enova DVX (3155HD or 2155HD) over the twisted pair cable and
features both a multi-format analog port to support legacy devices and an HDMI
port to support newer digital devices.
Common Applications
Mount the DXLink Multi-Format Wallplate Transmitter in the wall or lectern to connect guest equipment and send
audio and video signals across the room, on the other side of the house or in a classroom down the hall. Since it is
powered remotely, the wallplate can be installed virtually anywhere.
Features
Only One Cable – Send audio and video, while passing Ethernet signals and power over one twisted pair
cable
Multi-Format Analog Port and HDMI Port – Supports legacy analog signals - RGBHV, Component, S-Video,
and Composite, and digital HDMI/HDCP, DisplayPort++ and DVI signals
Send HDMI signals up to 100 meters – Extend the reach of the HDMI signals far beyond the capabilities of
typical HDMI cabling
Standard Twisted Pair Cable – Save time and effort in installation by leveraging cost effective twisted pair
cable, see the Cabling for Success with DXLink white paper for more details
Power over DXLink* Enabled – Designed for use with Enova DGX or DVX systems with DXLink inputs, PS-POE-
AT-TC (FG423-84) or PDXL-2 (FG1090-170) to provide remotely located Power over DXLink (requires firmware
v1.2.40 or above)
DXLink Direct Connection – When receiving Power over DXLink* from the PS-POE-AT-TC or PDXL-2, DXLink
Wallplates can be connected directly to a DXLink Receiver for a point-to-point solution
© 2013 AMX. All rights reserved.
Page 2
* Power must be supplied by one of the following DXLink Power sourcing devices: Enova DGX 8/16/32 Digital Media S witcher (with a DXLink
GENERAL
Dimensions (HWD)
4 11/16" x 6" x 1 5/16" (11.90 cm x 15.20 cm x 3.33
cm)
Installation
Mounts onto standard 2 gang US, UK or EU back boxes
Weight
Approx. 1.4 lb (0.64 kg)
Shipping Weight: Approx. 2.2 lb (1.0 kg)
Compatible AMX Products
•Enova DGX 8/16/32 Digital Media Switchers
•Enova DVX-3155 and 2155 All-In-One Presentation
Switchers
•DXLink HDMI RX as a point-to-point solution (when
Wallplates are powered by PS-POE-AT-TC or PDXL-2)
•PS-POE-AT-TC High Power PoE Injector
•PDXL-2 Power over DXLink Controller
Airflow
Natural convection via air vent openings on front, back
and top
MTBF
381,000 hours
Approvals
CE, FCC, UL, cUL, RoHS / WEEE compliant
ACTIVE POWER REQUIREMENTS
DXLink Power
Power must be supplied by a DXLink Power sourcing
device such as:
•Enova DGX 8/16/32 Digital Media Switcher (with a
DXLink Twisted Pair Input Board installed)
•Compatible Enova DVX All-In-One Presentation
Switcher (3155HD or 2155HD)
Twisted Pair Input Board installed), Compatible Enova DVX All-In-One Presentation Switcher (3155HD or 2155HD), PS-POE-AT-TC High Power
PoE Injector or PDXL-2 Power over DXLink Controller. AMX only supports the use of these approved Power over DXLink solutions. Other
third party power supplies or non-compatible standard PoE solutions may damage the DXLink equipment.
Dealer Benefits
HDMI/HDCP with the Simplicity of Analog - Hassle-free plug-and-play operation eliminates the need for
time consuming, cumbersome work-around tools to deal with HDCP key constraints and resolution
incompatibilities
Installation Friendly - Standard two gang size and remote powering capabilities allows the wallplate to be
installed in virtually any location
Customer Benefits
Interruption-Free Content - Exclusive InstaGate Pro® Technology allows audio and video to be switched
quickly and easily to every connected display without the difficulties typically associated with HDCP
Easily Connect Guest Devices - Provides a versatile solution for environments where sources are consistently
changing
Additional Features
Power Remotely - Power is carried over twisted pair to simplify installation when used with the Enova DGX
3D Support** - Pass through latest video formats including 3D and Deep Color
Surround Sound Support - Pass through high definition surround sound including Dolby Digital, DTS and up to
8-channel L-PCM at 32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192kHz
HDCP Compliant
**This feature will be available upon release of a future firmware update
Specifications
**This feature will be available upon release of a future firmware update
*** Cable runs with a minimum specification of ANSI/TIE/EIA 568A-5 and ratings of 250MHz or better may be used with DXLink equipment. However, cable
run topology and environmental influences can affect the overall successful distance capabilities of these runs. For successful deployments up to 100
meters without consideration to outside variables, AMX recommends the use of shielded category cable (STP) or Cat6A (or better) versions of unshielded or
shielded twisted pair (UTP/STP) for DXLink runs. For more details and helpful cabling information, please contact your AMX representative for a copy of the
white paper titled “Cabling for Success with DXLink”. IMPORTANT NOTICE: DXLink twisted pair cable runs for DXLink equipment s hould only be run within a
common building.
Page 3
•PS-POE-AT-TC High Power PoE Injector
•PDXL-2 Power over DXLink Controller
When installed in conjunction with an Enova DGX use
the Enova DGX Configuration Tool located at
AMX.com/enova to determine the power
requirements of the configuration
AMX only supports the use of these approved Power
over DXLink solutions. Other third party
power supplies or non-compatible standard PoE
solutions may damage the DXLink equipment. To use
PS-POE-AT-TC or PDXL-2 as a power source the
wallplates require firmware v1.2.40 or above
Power Connector
Included on DXLink Connection
Power Consumption (Max)
Power over DXLink supplied: 7 W
POWER SUPPLY
External, Required
Power must be supplied by a DXLink Power sourcing
device such as:
•Enova DGX 8/16/32 Digital Media Switcher (with a
DXLink Twisted Pair Input Board installed)
•Compatible Enova DVX All-In-One Presentation
Switcher (3155HD or 2155HD)
•PS-POE-AT-TC High Power PoE Injector
•PDXL-2 Power over DXLink Controller
AMX only supports the use of these approved Power
over DXLink solutions. Other third party
power supplies or non-compatible standard PoE
solutions may damage the DXLink equipment. To use
PS-POE-AT-TC or PDXL-2 as a power source the
wallplates require firmware v1.2.40 or above
ENVIRONMENTAL
Temperature (Operating)
32° to 104° F (0° to 40° C)
Temperature (Storage)
-22° to 158° F (-30° to 70° C)
Humidity (Operating)
5% to 85% RH (non-condensing)
Humidity (Storage)
0% to 90% RH (non-condensing)
Heat Dissipation (Max)
Enova DGX / DVX DXLink (PoE) supplied: 24 BTU/hr
FRONT CONNECTORS
HDMI Input
HDMI Type A Female
Analog Video Input
HD-15 (Breakout cable required for non RGB formats)
Analog Stereo Input
3.5mm Mini-Stereo Jack
Advanced Configuration Interface**
USB Mini-B Connector
USB (HID) Keyboard & Mouse**
USB Mini-B Connector
SIDE CONNECTORS
ID Pushbutton
Places system in NetLinx Device ID assignment mode
Reset Pushbutton
Resets/reboots the CPU of the wallplate
BACK CONNECTORS
DXLink Output
RJ-45
**This feature will be available upon release of a future firmware update
Page 4
CONTROL
Advanced Configuration Interface**
USB Mini-B Connector
Power Indicator
Green indicates whether or not the module is powered
on
**This feature will be available upon release of a future firmware update
INDICATORS
Power Indicator
Green indicates whether or not the module is powered
on
DXLink
Transport Layer Throughput (Max)
10.2 Gbps
Twisted Pair Cable Type
Cat5e, Cat6/6e, Cat6A, Cat7 of UTP, SF/UTP, S/FTP,
and F/UTP varieties ***
Twisted Pair Cable Length
Up to 328 ft (100 m)***
HDMI
Compatible Formats
HDMI, HDCP , DVI
Input Signal Type
HDMI
DVI-D (Single Link With Cable Adapter)
DisplayPort ++ (Input Only, With HDMI Cable Adapter)
Input Connector
HDMI Type A Female
Propagation Delay (Typ)
5 us
Input Voltage (Nominal)
1.0 Vpp Differential
Input Re-clocking (CDR)
Yes
Input Equalization
Yes, Adaptive
Data Rate (Max)
4.95 Gbps / 6.75 Gbps
6.75 Gbps supported when the DXLink HDMI RX Scaler
is in Bypass mode and format is 1080p60 or less
Pixel Clock (Max)
165 MHz / 225 MHz
225 MHz supported when the DXLink HDMI RX Scaler
is in Bypass mode and format is 1080p60 or less
Progressive Resolution Support
480p up to 1920x1200 @ 60 Hz including but not
limited to those resolutions shown in the DXLink
Twisted Pair Transmitters/Receiver Instruction Manual
Interlaced Resolution Support
480i, 576i, 1080i including but not limited to those
resolutions shown in the DXLink Twisted Pair
Transmitters/Receiver Instruction Manual. If input is
interlaced, all scaled outputs will deinterlace video to a
progressive resolution format. If in scaler Bypass mode
interlaced input will pass through
Deep Color Support**
24-bit, 30-bit, 36-bit
30-bit, 36-bit supported when the DXLink HDMI Rx
Scaler is in Bypass mode and format is 1080p60 or less
Color Space Support
RGB 4:4:4
YCbCr 4:4:4 and 4:2:2
(Input signal support for YCbCr 4:4:4 and 4:2:2, output
color-space is converted to RGB 4:4:4)
3D Format Support**
Yes (HDMI Primary Formats)
Frame Packing 1080p up to 24Hz
*** Cable runs with a minimum specification of ANSI/TIE/EIA 568A-5 and ratings of 250MHz or better may be used with DXLink equipment. However, cable
run topology and environmental influences can affect the overall successful distance capabili ties of these runs. For successful deployments up to 100
meters without consideration to outside variables, AMX recommends the use of shielded category cable (STP) or Cat6A (or better) versions of unshielded or
shielded twisted pair (UTP/STP) for DXLink runs. For more details and helpful cabling information, please contact your AMX representative for a copy of the
white paper titled “Cabling for Success with DXLink”. IMPORTANT NOTICE: DXLink twisted pair cable runs for DXLink equipment s hould only be run within a
common building.
Page 5
Frame Packing 720p up to 50/60Hz
Frame Packing 1080i up to 50/60Hz
Top-Bottom 1080p up to 24Hz
Top-Bottom 720p up to 50/60Hz
Side-by-Side Half 1080p up to 50/60Hz
Side-by-Side Half 720p up to 50/60Hz
3D supported when the DXLink HDMI Rx
Scaler is in Bypass mode and format is 1080p60 or less
Audio Format Support
Dolby TrueHD**, Dolby Digital, DTS-HD Master
Audio**, DTS, 2 CH through 8 CH L-PCM
Dolby Digital and DTS support up to 48kHz, 5.1
channels
Audio Resolution
16 bit to 24 bit
Audio Sample Rate
32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192kHz
Local Audio Support
Yes for audio insertion
HDCP Support
Yes
Supports AMX HDCP InstaGate Pro Technology
When used with an Enova DGX 8/16/32 Digital Media
Switcher the key support is up to 16 sinks per output,
independent of source device
When used as a single point to point solution the key
support is defined by the source device
CEC Support
None
DDC/EDID Support
The HDMI EDID in point to point mode is passed up
from the sink device.
When used with Enova DGX 8/16/32 Digital Media
Switcher or Enova DVX-2155 or 3155 the HDMI EDID is
passed from the Enova Switcher input to the TX and is
user reprogrammable. The analog video input
connection provides a fixed EDID set
**This feature will be available upon release of a future firmware update
ANALOG VIDEO
Compatible Formats
RGBHV, RGBs, RGsB
YPbPr (HDTV)
Y/c (S-Video), C (Composite)
Progressive Resolution Support
480p up to 1920x1200 @ 60 Hz (reference the DXLink
Twisted Pair Transmitters/Receiver Instruction Manual
for extended list)
Interlaced Resolution Support
480i, 576i, 1080i (reference DXLink Twisted Pair
Transmitters/Receiver Instruction Manual for
extended list)
If input is interlaced, all scaled outputs will deinterlace
video to a progressive resolution format. If in scaler
Bypass mode interlaced input will pass through
unaltered
Auto-Adjust Input**
Supported
RGB Input Signal Level Range
1 Vpp nominal
RGB Input Impedance
75 Ω
HV Sync Input Signal Level Range
2 to 5 Vpp
HV Sync Input Impedance
2.5 pF Typ, 10 pF Max
Digital Processing
24 bit, 165 MHz
Y/Pb/Pr Input Signal Level Range
1.0 Vpp for Y, 700 mVpp for Pb Pr
Y/Pb/Pr Input Impedance
75 Ω
Y/c (S-Video) Input Signal Level Range
1.0 Vpp for Y, 300 mVpp for c
Y/c (S-Video) Input Impedance
75 Ω
Page 6
C (Composite) Input Signal Level Range
1.0 Vpp
C (Composite) Input Impedance
75 Ω
Input Connector
HD-15 (Breakout cable required for non RGBHV
formats)
**This feature will be available upon release of a future firmware update
AUDIO (ANALOG & DIGITAL S/PDIF)
Input Signal Types
Stereo Analog, S/PDIF
Video signal must be present to pass Audio
Analog Input Level (Max)
+2 dBu, unbalanced
Analog Input Impedance
10k Ω
Analog to Digital Conversion
48 kHz Sample Rate, 24-bit
S/PDIF Audio Format Support
Dolby Digital, DTS, 2 CH L-PCM
Dolby Digital and DTS support up to 48kHz, 5.1
channels
S/PDIF Resolution
16 to 24 bit
S/PDIF Sample Rate
32 kHz, 44.1 kHz, 48 kHz, 96 kHz
S/PDIF Input Signal Level Range
200 mVpp to 600mVpp terminated
S/PDIF Input Impedance
75 Ω
Analog to Digital Reference Level
+2.5 dBu = 0 dBfs
Input Connectors
3.5mm Mini-Stereo Jack (Analog Stereo)
RCA Jack (S/PDIF)
Page 7
About AMX
AMX hardware and software solutions simplify the implementation, maintenance, and use of technology to create effective environments. With the increasing number of
technologies and operating platforms at work and home, AMX solves the complexity of managing this technology with reliable, consistent and scalable systems. Our award-winning
products span control and automation, system-wide switching and audio/video signal distribution, digital signage and technology management. They are implemented worldwide in
conference rooms, homes, classrooms, network operation / command centers, hotels, entertainment venues, broadcast facilities, and more. ©2013 AMX. All rights reserved.
Specifications subject to change. Revised 28-Jan-13.
AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153
Loading...