
                      DATA SHEET 
DXLinkTM Multi-Format Decor Style 
Wallplate Transmitters (US) 
DX-TX-DWP-BL (FG1010-325-BL) 
DX-TX-DWP -WH (FG1010-325-WH)  
Overview 
The DXLink Multi-Format Decor Style Wallplate Transmitter sends analog or digital 
video including HDMI/HDCP, along with embedded audio or supplemental analog 
audio up to 100 meters to an Enova DGX Digital Media Switcher, compatible Enova 
DVX All-In-One Presentation Switcher, or directly to a DXLink Receiver. It receives 
Power over DXLink* from the Enova DGX, Enova DVX (3155HD, 3156HD or 2155HD), 
PS-POE-AT-TC High Power PoE Injector or PDXL-2 Dual Power over DXLink 
Controller over the twisted pair cable and features both a multi-format analog port 
to support legacy devices and an HDMI port to support newer digital devices. 
Common Applications 
Mount the DXLink Multi-Format Decor Style Wallplate Transmitter in the wall, lectern or popular floor box to 
connect guest equipment and send audio and video signals across the room, on the other side of the house or in a 
classroom down the hall. Since it is powered remotely, the wallplate can be installed virtually anywhere. 
Features 
  Only One Cable – Send audio and video, while passing Ethernet signals and power over one twisted pair 
cable 
  Multi-Format Analog Port and HDMI Port – Supports legacy analog signals - RGBHV, Component, S-Video, 
and Composite, and digital HDMI/HDCP, DisplayPort++ and DVI signals 
© 2014 AMX. All rights reserved. 

  Send HDMI signals up to 100 meters – Extend the reach of the HDMI signals far beyond the capabilities of 
4 1/16" x 3 1/2" x 2 1/4" (10.31 cm x 8.84 cm x 5.72 
cm) 
Mounts onto standard double-gang US back box 
Mounts into standard decor style wallplates (not 
included) 
Approximately 75 lb (0.34 kg) 
typical HDMI cabling 
  Standard Twisted Pair Cable – Save time and effort in installation by leveraging cost effective twisted pair 
cable, see the Cabling for Success with DXLink white paper for more details 
  Easy Installation – Mounts in standard decor style wallplates  
  Power over DXLink* Enabled – Designed for use with Enova DGX or DVX systems with DXLink inputs, PS-POE-
AT-TC (FG423-84) or PDXL-2 (FG1090-170) to provide remotely located Power over DXLink (requires firmware 
v1.2.40 or above) 
  DXLink Direct Connection – When receiving Power over DXLink* from the PS-POE-AT-TC or PDXL-2, DXLink 
Wallplates can be connected directly to a DXLink Receiver for a point-to-point solution 
* Power must be supplied by one of the following DXLink Power sourcing devices: Enova DGX 8/16/32/64 Digital Media Switcher (with a 
DXLink Twisted Pair Input Board installed), Compatible Enova DVX All-In-One Presentation Switcher (3155HD, 3156HD or 2155HD), PS-POEAT-TC High Power PoE Injector or PDXL-2 Power over DXLink Controller. AMX only supports the use of these approved Power over DXLink 
solutions. Other third party power supplies or non-compatible standard PoE solutions may damage the DXLink equipment. 
Dealer Benefits 
  HDMI/HDCP with the Simplicity of Analog - Hassle-free plug-and-play operation eliminates the need for 
time consuming, cumbersome work-around tools to deal with HDCP key constraints and resolution 
incompatibilities 
  Installation Friendly - Standard two gang size and remote powering capabilities allows the wallplate to be 
installed in virtually any location 
  Complements Any Environment - Decor Wallplate is available in black or white and blends well in both 
commercial and residential applications 
Customer Benefits 
  Interruption-Free Content - Exclusive InstaGate Pro® Technology allows audio and video to be switched 
quickly and easily to every connected display without the difficulties typically associated with HDCP 
  Easily Connect Guest Devices - Provides a versatile solution for environments where sources are consistently 
changing 
Additional Features 
  Power Remotely – Power over DXLink* is carried over twisted pair to simplify installation when used with the 
Enova DGX, Enova DVX, PS-POE-AT-TC or PDXL-2 
  3D Support - Pass through latest video formats including 3D and Deep Color  
  Surround Sound Support - Pass through high definition surround sound including Dolby TrueHD, DTS-HD 
Master Audio, Dolby Digital, DTS and 2-channel through 8-channel L-PCM at 32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 
192kHz 
  HDCP Compliant 
* Power must be supplied by one of the following DXLink Power sourcing devices: Enova DGX 8/16/32/64 Digital Media Switcher (with a 
DXLink Twisted Pair Input Board installed), Compatible Enova DVX All-In-One Presentation Switcher (3155HD, 3156HD or 2155HD), PS-POEAT-TC High Power PoE Injector or PDXL-2 Power over DXLink Controller. AMX only supports the use of these approved Power over DXLink 
solutions. Other third party power supplies or non-compatible standard PoE solutions may damage the DXLink equipment. 
Specifications 
2 

Approximately 1.3 lb (.61 kg) 
Natural convection via air vent openings on front, back 
and top 
•Enova DGX 8/16/32/64 Digital Media Switchers 
•Enova DVX-3155HD, DVX-3156HD and DVX-2155HD 
All-In-One Presentation Switchers 
•DXLink HDMI RX as a point-to-point solution (when 
Wallplates are powered by PS-POE-AT-TC or PDXL-2) 
•PS-POE-AT-TC High Power PoE Injector 
•PDXL-2 Power over DXLink Controller 
FCC 
CE EN 55022 
CE EN 55024 
CE EN 60950-1 
IEC 60950-1 
UL 60950-1 
RoHS / WEEE compliant 
CC-USB, USB Programming Cable (FG10-5965) 
Transport Layer Throughput (Max) 
Shielded Cat6, Cat6A and Cat7 
DXLink twisted pair cable runs for DXLink equipment 
shall only be run within a common building where a 
common building is defined as: the walls of the 
structure(s) are physically connected and the 
structure(s) share a single ground reference 
For more details and helpful cabling information, 
reference the white paper titled Cabling for Success 
with DXLink, or contact your AMX representative 
Twisted Pair Cable Length 
ACTIVE POWER REQUIREMENTS 
Power must be supplied by a DXLink Power sourcing 
device such as: 
•Enova DGX 8/16/32/64 Digital Media Switcher (with a 
DXLink Twisted Pair Input Board installed) 
•Compatible Enova DVX All-In-One Presentation 
Switcher (DVX-3155HD, DVX-3156HD or DVX-2155HD) 
•PS-POE-AT-TC High Power PoE Injector 
•PDXL-2 Power over DXLink Controller 
When installed in conjunction with an Enova DGX use 
the Enova DGX Configuration Tool located at 
AMX.com/enova to determine the power 
requirements of the configuration 
AMX only supports the use of these approved Power 
over DXLink solutions. Other third party 
power supplies or non-compatible standard PoE 
solutions may damage the DXLink equipment. To use 
PS-POE-AT-TC or PDXL-2 as a power source the 
wallplates require firmware v1.2.40 or above 
Included on DXLink Connection 
Power over DXLink supplied: 7 W 
3 

Power must be supplied by a DXLink Power sourcing 
device such as: 
•Enova DGX 8/16/32/64 Digital Media Switcher (with a 
DXLink Twisted Pair Input Board installed) 
•Compatible Enova DVX All-In-One Presentation 
Switcher (DVX-3155HD, DVX-3156HD or DVX-2155HD) 
•PS-POE-AT-TC High Power PoE Injector 
•PDXL-2 Power over DXLink Controller 
AMX only supports the use of these approved Power 
over DXLink solutions. Other third party 
power supplies or non-compatible standard PoE 
solutions may damage the DXLink equipment. To use 
PS-POE-AT-TC or PDXL-2 as a power source the 
wallplates require firmware v1.2.40 or above 
32° to 104° F (0° to 40° C) 
-22° to 158° F (-30° to 70° C) 
5% to 85% RH (non-condensing) 
0% to 90% RH (non-condensing) 
Power over DXLink supplied: 24 BTU/hr 
User Accessible (accessible with faceplate mounted) 
HD-15 (Breakout cable required for non RGB formats) 
USB (HID) Keyboard & Mouse 
Setup Front Connectors (not accessible with 
faceplate mounted) 
Advanced Configuration Interface 
Toggle between DHCP and static IP addressing 
Places system in NetLinx Device ID assignment mode 
Reset the factory default settings 
Restore the factory firmware image  
Resets/reboots the CPU of the wallplate 
Advanced Configuration Interface 
Green indicates whether or not the module is powered 
on 
4 

USB (HID) KEYBOARD & MOUSE 
(1) USB Mini A/B Connector (“HOST”) 
Use in conjunction with an Enova DGX Digital Media 
Switcher, connect a DXLink TX (twisted pair or fiber) to 
a PC and emulate keyboard and mouse commands 
from a DXLink Fiber Receiver (twisted pair or fiber) 
For a list of HID devices which have been tested and 
found to be working well with the latest firmware 
please visit: http://www.amx.com/products/AVB-RXDXLINK-HDMI.asp and view the document “DXLink HID  
Keyboard and Mouse Supported Devices”. 
HDMI 
DVI-D (Single Link With Cable Adapter)  
DisplayPort ++ (Input Only, With HDMI Cable Adapter)  
6.75 Gbps supported when the DXLink HDMI RX Scaler 
is in Bypass mode and format is 1080p60 or less 
165 MHz / 225 MHz 
225 MHz supported when the DXLink HDMI RX Scaler 
is in Bypass mode and format is 1080p60 or less 
Progressive Resolution Support 
480p up to 1920x1200 @ 60 Hz including but not 
limited to those resolutions shown in the DXLink 
Twisted Pair Transmitters/Receiver Instruction Manual 
Interlaced Resolution Support 
480i, 576i, 1080i including but not limited to those 
resolutions shown in the DXLink Twisted Pair 
Transmitters/Receiver Instruction Manual. If input is 
interlaced, all scaled outputs will deinterlace video to a 
progressive resolution format. If in scaler Bypass mode 
interlaced input will pass through 
24-bit, 30-bit, 36-bit 
30-bit, 36-bit supported when the DXLink HDMI RX 
Scaler is in Bypass mode and format is 1080p60 or less 
RGB 4:4:4  
YCbCr 4:4:4 and 4:2:2 
(Input signal support for YCbCr 4:4:4 and 4:2:2, output 
color-space is converted to RGB 4:4:4) 
Yes, when scaler on corresponding output board or 
DXLink RX is set to Bypass mode 
Frame Packing 1080p up to 24Hz 
Frame Packing 720p up to 50/60Hz 
Frame Packing 1080i up to 50/60Hz 
Top-Bottom 1080p up to 24Hz 
Top-Bottom 720p up to 50/60Hz 
Side-by-Side Half 1080p up to 50/60Hz 
Dolby TrueHD, Dolby Digital, DTS-HD Master 
Audio, DTS, 2 CH through 8 CH L-PCM 
Dolby Digital and DTS support up to 48kHz, 5.1 
5 

32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192kHz 
Yes 
Supports AMX HDCP InstaGate Pro Technology 
When used with an Enova DGX 8/16/32/64 Digital 
Media Switcher the key support is up to 16 sinks per 
output, independent of source device 
When used as a single point to point solution the key 
support is defined by the source device 
The HDMI EDID in point to point mode is passed up 
from the sink device. 
When used with Enova DGX 8/16/32/64 Digital Media 
Switcher or Enova DVX-3155HD, DVX-3156HD or DVX 
2155HD the HDMI EDID is passed from the Enova 
Switcher input to the TX and is user 
reprogrammable. The analog video input connection 
provides a fixed EDID set 
RGBHV, RGBs, RGsB 
YPbPr (HDTV) 
Y/c (S-Video), C (Composite) 
Progressive Resolution Support 
480p up to 1920x1200 @ 60 Hz (reference the DXLink 
Twisted Pair Transmitters/Receiver Instruction Manual 
for extended list) 
Interlaced Resolution Support 
480i, 576i, 1080i (reference DXLink Twisted Pair 
Transmitters/Receiver Instruction Manual for 
extended list) 
If input is interlaced, all scaled outputs will deinterlace 
video to a progressive resolution format. If in scaler 
Bypass mode interlaced input will pass through 
unaltered 
RGB Input Signal Level Range 
HV Sync Input Signal Level Range 
Y/Pb/Pr Input Signal Level Range 
1.0 Vpp for Y, 700 mVpp for Pb Pr 
Y/c (S-Video) Input Signal Level Range 
1.0 Vpp for Y, 1.0 Vpp for c 
Y/c (S-Video) Input Impedance 
C (Composite) Input Signal Level Range 
C (Composite) Input Impedance 
HD-15 (Breakout cable required for non RGBHV 
formats) 
AUDIO (ANALOG & DIGITAL S/PDIF) 
Stereo Analog, S/PDIF 
Video signal must be present to pass Audio 
6 

Analog to Digital Conversion 
48 kHz Sample Rate, 24-bit 
S/PDIF Audio Format Support 
Dolby Digital, DTS, 2 CH L-PCM 
Dolby Digital and DTS support up to 48kHz, 5.1 
channels 
32 kHz, 44.1 kHz, 48 kHz, 96 kHz 
S/PDIF Input Signal Level Range 
200 mVpp to 600mVpp terminated 
Analog to Digital Reference Level 
3.5mm Mini-Stereo Jack (Analog Stereo) 
RCA Jack (S/PDIF) 
For a detailed PDF or DXF pictorial drawing please visit: http://www.amx.com/products/DX-TX-DWP.asp 
About AMX 
AMX hardware and software solutions simplify the implementation, maintenance, and use of technology to create effective environments. With the increasing number of 
technologies and operating platforms at work and home, AMX solves the complexity of managing this technology with reliable, consistent and scalable systems. Our award-winning 
products span control and automation, system-wide switching and audio/video signal distribution, digital signage and technology management. They are implemented worldwide in 
conference rooms, homes, classrooms, network operation / command centers, hotels, entertainment venues, broadcast facilities, and more. ©2014 AMX. All rights reserved. 
Specifications subject to change. Revised 11-August-2014. 
AMX.com  |  800.222.0193  |  469.624.8000  |  +1.469.624.7400  |  fax 469.624.7153 
7