Amprobe PY-1A User Manual

PY-1A

AC / DC Voltage Tester

Users Manual

• Mode d’emploi

• Bedienungshandbuch

• Manual d’Uso

• Manual de uso

Limited Warranty and Limitation of Liability

Your Amprobe product will be free from defects in material and
workmanship for 1 year from the date of purchase. This warranty does
not cover fuses, disposable batteries or damage from accident, neglect,
misuse, alteration, contamination, or abnormal conditions of operation or
handling. Resellers are not authorized to extend any other warranty on
Amprobe’s behalf. To obtain service during the warranty period, return
the product with proof of purchase to an authorized Amprobe Test
Tools Service Center or to an Amprobe dealer or distributor. See Repair
Section for details. THIS WARRANTY IS YOUR ONLY REMEDY. ALL OTHER
WARRANTIES - WHETHER EXPRESS, IMPLIED OR STAUTORY - INCLUDING
IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR
MERCHANTABILITY, ARE HEREBY DISCLAIMED. MANUFACTURER
SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM ANY CAUSE
OR THEORY. Since some states or countries do not allow the exclusion
or limitation of an implied warranty or of incidental or consequential
damages, this limitation of liability may not apply to you.

Repair

All test tools returned for warranty or non-warranty repair or for
calibration should be accompanied by the following: your name,
company’s name, address, telephone number, and proof of purchase.
Additionally, please include a brief description of the problem or the
service requested and include the test leads with the meter. Non-warranty
repair or replacement charges should be remitted in the form of a check,
a money order, credit card with expiration date, or a purchase order made
payable to Amprobe® Test Tools.

In-Warranty Repairs and Replacement – All Countries

Please read the warranty statement and check your battery before
requesting repair. During the warranty period any defective test
tool can be returned to your Amprobe® Test Tools distributor for an
exchange for the same or like product. Please check the “Where to
Buy” section on www.amprobe.com for a list of distributors near you.
Additionally, in the United States and Canada In-Warranty repair and
replacement units can also be sent to a Amprobe® Test Tools Service
Center (see next page for address).

Non-Warranty Repairs and Replacement – US and Canada

Non-warranty repairs in the United States and Canada should be sent
to a Amprobe® Test Tools Service Center. Call Amprobe® Test Tools or
inquire at your point of purchase for current repair and replacement
rates.

In USA In Canada
Amprobe Test Tools Amprobe Test Tools
Everett, WA 98203 Mississauga, ON L4Z 1X9
Tel: [phone] Tel: [phone]
Fax: [phone] Fax: [phone]

Non-Warranty Repairs and Replacement – Europe

European non-warranty units can be replaced by your Amprobe® Test
Tools distributor for a nominal charge. Please check the “Where to
Buy” section on www.amprobe.com for a list of distributors near you.

Amprobe® Test Tools Europe
In den Engematten 14
79286 Glottertal, Germany
tel: [phone] - 0
*(Correspondence only – no repair or replacement available from this
address. European customers please contact your distributor.)

PY-1A AC / DC Voltage Tester

Test Probes

1

Neon for Voltage indication

2

3

Pocket Clip

CONTENTS

SYMBOLS ............................................................................ 2

UNPACKING AND INSPECTION ......................................... 5

INTRODUCTION .................................................................. 5

OPERATION .........................................................................5

SPECIFICATION ...................................................................6

MAINTENANCE ................................................................... 6

TROUBLE SHOOTING ..........................................................7

1

SYMBOLS

Warning of a potential danger, comply with



instruction manual.

Caution! Dangerous Voltage. Danger of



electrical shock.

Continous double or reinforced insulation



complies with Category II IEC 536

Confirmity symbol, the instrument complies
with the valid directives. It complies with the
EMC Directive (89/336/EEC), Standards EN
50081 and EN 50082-1 are fulfilled. It also



complies with the low Voltage Directive (73/23/
EEC), Standard EN 61010-1 is fulfilled.
Measurement category III is for measurements
performed in the building installation.

Instrument complies with the standard



(2002/96/EEC) WEEE

The instruction manual contains information
and references, nessary for safe operation and



maintenance of the instrument.

Warnings!



This Electrical Tester has been constructed and verified
in compliance with the lasted safety standards and have
left the factory in safe and perfect conditions. Prior to
using the instrument (commissioning/assembly) the user
is kindly requested to thoroughly read the instruction
manual and comply with it in all sections.

• Failure to read the instruction manual or to

comply with the warnings and references
contained herein can result in serious bodily injury
or instrument damage.

2

• The respective accident prevention regulations

established by the professional associations for
electrical system and equipment must be strictly
met at all times.

• In order to avoid electrical shock, the valid safety

regarding excessive contact voltages must receive
utmost attention, when working with voltages
exceeding 120V (60V) DC or 50V (25V) rms AC. The
values in bracket are valid for limited ranges (as
for example medicine and agriculture).

• Never connect the tester to voltage for longer

than 30 seconds. For next operation, a recovery
time of minimum 240 seconds is needed

• The instrument may only be used within the

operating ranges as specified in the technical data
section and in low voltage system up to 600V.

• Measurements in dangerous proximity of electrical

system are only to be carried out in compliance
with the instructions of a responsible electronics
technician, and never alone.

• The electrical testers may no longer be used if one

or several functions fail or if no functionality is
indicated.

• Do not use this instrument under damp conditions.

• Perfect display is only guaranteed within a

temperature range of 5°C up to +40°C at relative
humidity <80%.

• Test leads and test probes may only be touched

at handle surfaces provided. Absolutely avoid the
direct contact of the rest probes.

• Prior to usage ensure perfect instrument function

(e.g. on known voltage source).

• The instrument may only be opened by an

authorized service technician.

3

The safety can no longer be insured if the instrument:

• Shows obvious damage.

• Does not carry out the desired measurements.

• Has been stored for too long under unfavorable

conditions

• Has been subjected to mechanical stress during

transport.

• Avoid any heating up of the instrument by direct

sunlight to ensure perfect functioning and long
instrument life.

• The instrument may only be used under those

conditions and for those purposes for which it
was conceived. For this reason, in particular the
safety references, the technical data including
environmental conditions and the usage in dry
environments must be followed. When modifying
or changing the instrument, the operational safety
is no longer ensured.

• The instrument may only be used under those

conditions and for which it was conceived. For
this reason, in particular the safety references,
the technical data including the environmental
conditions and the usage in dry environments
must be followed.

UNPACKING AND INSPECTION

Your shipping carton should include:

1 Electrical Tester PY-1A

1 Instruction Manual

If any of the items are damaged or missing, return
the complete package to the place of purchase for an

exchange.

4

INTRODUCTION

This Electrical Tester is for universal applications for
indoor use only. It represents a valuable support for all
testing in handicraft and industrial applications.

The electrical tester is characterized by the following
features.

• AC voltage detection up to 480V, and DC voltage

upto 600V.

• Bright neon AC/DC voltage display.

• Ergonomically and robust housing.

• Snap-in leads are spaced to t to the standard US/

Canada outlet, for easy, one hand operation.

• Integral probe storage for easy carrying.

OPERATION

• Test the electrical tester on a known source.

• Connect both test leads with UUT.

• The voltage is displayed via Neon lamps.

• The instrument with 120, 240, 277, 480V AC range

and 160, 330, 380, 600V DC range.

SPECIFICATION

Voltage Range 120, 240, 277, 480V AC

160, 330, 380, 600V DC

Response Time <0,3s
Frequency Range DC, 0~65Hz
Interal Load approx. 2.0 W/ 600V
Test Current <3.5 mA
Operation Time (DT) 30s
Recovery Time 240s
Temperature Range 5°C ~ +40°C (41°F ~ 104°F)

5

Humidity Max. 80% rel. H.
Height above sea level up to 2000 m (6562 ft)
Measurement Cat. CATIII / 600V
Pollution Degree 2
Safety Standards IEC 61010, UL 61010, CSA

22.2 No. 61010

Weight Approx. 50g (0.11 lb)
Dimension Approx. 150X32X26 mm

(5.9x1.3x1.0 in)

MAINTENACE

When using the instrument in compliance with the
instruction manual, no special maintenance is required.
Should operational problems occur during daily use, our
consulting service will be at your disposal, free of charge.

If functional errors occur after expiration of warranty,
the repairing of the tester should be performed only by
a Factory Authorized Service Center or by other qualified
instrument service personnel. The front panel and
case can be cleaned with a mild solution of detergent
and water. Apply sparingly with a soft cloth and allow
to dry completely before using. Do not use aromatic
hydrocarbons or chlorinated solvents for cleaning.

Do not attempt to repair this tester. It contains no user­serviceable parts. Repair or servicing should only be
performed by qualified personnel.

TROUBLE SHOOTING

If the instrument fails to operate, check test leads, and
replace as necessary. Double check operating procedure
as described in this user’s manual.

6