Page 1
Data Sheet
ACD-45PQ
600A Power Quality Clamp
The ACD-45PQ is a compact clamp meter capable of measuring
power, energy and power factor on a single and three-phase
systems (balanced and unbalanced). Ultra slim jaw design allows
the user to clamp around conductors in confined and difficult to
reach places. Add on troubleshooting capabilities with an optional
PC interface kit.
TRMS sensing
Ultra slim jaws accommodate conductors up to 1.02” (26mm)
in diameter
Measurements: AC/DC Voltage up to 600V, AC Current up
to 600A, Resistance, Frequency Power: Active (W),
Reactive (VAR) and Apparent (VA) Power with dual-display
Power Factor readout, KWh Recording
No hassle
warranty
No waiting.
No shipping
charges.
Our commitment to
high-quality products
and customer service
is demonstrated by
our industry exclusive
“No Hassle” warranty.
In the unlikely event
that an Amprobe Test
Tool requires warranty
service, any of our
local dealers are
authorized to replace
it, on the spot.
(note: $500 MSLP limit)
AutoVA - Auto Selection of AC Volts, DC Volts or AC Amps
3 phase unbalanced load measurement – calculation of the
discrete single phase measurements
Optional PC interface capability (RS-232 KIT2)
Audible continuity
Large, easy to read LCD display with backlight
Auto power off
Low battery indication
Peak hold
Data hold
Carrying case, test leads, batteries (installed), and manual
included
Voltage overload protection for all functions up to 600V AC/
DC
Safety CAT III 600V
Amprobe® Test Tools
www.Amprobe.com
Page 2
ACD-45PQ 600A Power Quality Clamp
Data Sheet
General Specifications
Display Voltage functions: 6000 counts LCD displayPower
Ohm & Hz functions: 9999 counts LCD display
ACA clamp-on function: 4000 counts LCD display
Update Rate Power function: 2 per second nominal Voltage, ACA clamp-on & Ohm functions: 2 per second
nominal Hz function: 1 per second nominal
Polarity Automatic
Low Battery Below approx. 2.4V
Operating Temperature 0°C to 40°C (32° to 104°F)
Relative Humidity Maximum relative humidity 80% for temperature up to 31°C (88°F)
decreasing linearly to 50% relative humidity at 40°C (104°F)
Altitude Operating below 2000m
Storage Temperature -20°C to 60°C (-4° to 140°F), < 80% R.H. (with battery removed)
Temperature Coefficient Nominal 0.15 x (specified accuracy)/ °C @(0°C-18°C or 28°C -40°C) /
(32° to 64°F or 82° to 104°F),or otherwise specified
Sensing True RMS sensing
Safety Meets IEC61010-1 2nd Ed., EN61010-1 2nd Ed., UL61010-1 2nd Ed.,
CAN/CSA C22.2 No.61010.1-0.92, IEC61010-2-032, EN61010-2-032 & UL61010B-2-032
Measurement Category III 600 Volts ac & dc
E.M.C. Meets EN61326-1:2006 (EN55022, EN61000 -3-2, EN61000-3-3, EN61000 -4-2, EN61000-4-3,
EN61000-4-4, , EN61000-4-5, EN61000-4-6, EN61000 -4 -8, EN61000-4-11)
Power Supply standard 1.5V AA A Size (NEDA 24A or IEC LR03) battery X 2
Power Consumption Voltage, ACA, Hz & Power functions: 11mA typical
Ohm function: 5.5mA typical
APO Timing Idle for 30 minutes
APO Consumption 4μA typical
Dimension L266.7 x W177.8 x H81.28mm (10.5 x 7 x 3.2in)
Weight 224 gm approx 192 gm approx (0.42 lb)
Jaw Opening 26mm (1.0 in) max
Special Features Backlighted display; AutoVATM (Auto Selection on ACV, DCV or ACA functions);
selectable Power parameters of W, VAR & VA with Total Power Factor in dual-display;
kWHr Recording; Display Hold; PEAK-rms HOLD
Amprobe® Test Tools
www.Amprobe.com
Page 3
ACD-45PQ 600A Power Quality Clamp
Data Sheet
Electrical Specification
Range Accuracy
AC Current 40.00 / 400.0 / 600 (1.0% Rdg + 5 LSD) @ 50 and 60Hz**
AC Voltage 600.0V +/-(0.5% Rdg + 5 LSD) @ 50 and 60Hz
DC Voltage 600.0V +/-(0.5% Rdg + 5 LSD)
Resistance 999.9 Ohms +/-(1.0% Rdg + 6 LSD)
Frequency 5.00Hz to 500.0Hz +/-(0.5% Rdg +4 LSD)
Active Power (W) 0 to 360.0 kW +/-(2.0% Rdg + 6 LSD)
@ Harmonics Fund to 10th & PF 0.1 to 0.99
Reactive Power (VAR) 0 to 360.0 kVAR +/-(2.0% Rdg + 6 LSD)
@ Harmonics Fund to 10th & PF > 0.7
Apparent Power (VA) 0 to 360.0 kVA +/-(2.0% Rdg + 6 LSD) @ Harmonics Fund to 10th
Power Factor 0.10 to 0.99 +/- 3 LSD @ Harmonics Fund to 21th
Optional Accessories Part Number
PC Interface Kit (PC connection cable with software) RS-232 KIT2
Software www.amprobe.com
Replacement Parts (supplied with product) Part Number
Test Leads With Set Of Alligator Clips MTL-90B
(alligator clips are not supplied with product)
Instruction Manual www.amprobe.com
Amprobe® Test Tools
www.Amprobe.com
Page 4
ACD-45PQ 600A Power Quality Clamp
Data Sheet
Amprobe® Test Tools
website: www.Amprobe.com
email: info@amprobe.com
Everett, WA 98203
Tel: 877-AMPROBE
Amprobe® Test Tools
Amprobe® Test Tools Europe
In den Engematten 14
79286 Glottertal, Germany
Tel.: +49 (0) 7684 8009 - 0
©2010 Amprobe Test Tools . All righ ts reserved.
6/2010 ACD-4 5PQ_ DS Rev A
www.Amprobe.com
Loading...