Ampeg BA-110 User Manual

BA-110
BASS AMPLIFIER
Owner ’s Manual
BA-110 BASS AMPLIFIER
IMPORTANT SAFEGUARDS AND PRECAUTIONS:
All Ampeg products are designed for continuous safe operation, as long as common sense is used and steps are taken to help avoid certain problems. Abiding by the following rules can help prevent damage to your amplifier, yourself and others.
Connect the amplifier ONLY to a properly grounded AC outlet of the proper voltage for your amp.
Avoid sudden temperature extremes, rain and moisture. Also, avoid sudden and intense impact. (If the unit has been subjected to any of the preceding abuses, have it looked at by an authorized service center.)
NEVER set the amplifier on a support that might give out under its weight.
Always keep the total speaker impedance at or above the rated load.
Unplug the amplifier before cleaning it. NEVER spray liquid cleaners onto the ampli-
fier. Wipe it with a slightly dampened, lint-free cloth to remove dirt and film.
Do not use the amplifier if it has sustained damage to the chassis, controls, or power cord. Refer the unit to an authorized service center for inspection.
Amplifiers capable of producing high volume levels are also capable of inflicting per­manent hearing loss or damage, if the exposure to such levels is prolonged. Such damage is progressive and irreversible!
THIS EQUIPMENT HAS BEEN DESIGNED AND ENGINEERED TO PROVIDE SAFE AND RELIABLE OPERATION. IN ORDER TO PROLONG THE LIFE OF THE UNIT AND PREVENTACCIDENTAL DAMAGES OR INJURY, PLEASE FOLLOW THESE PRECAUTIONARY GUIDELINES:
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT OPEN CHASSIS; DO NOT DEFEATOR REMOVE THE GROUND PIN OF THE POWER CORD; CONNECT ONLYTO A PROPERLY GROUNDED AC POWER OUTLET.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOTEXPOSE THIS EQUIPMENTTO RAIN OR MOISTURE. CAUTION: NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION: OUR AMPLIFIERS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED EXPOSURE TO HIGH SOUND PRESSURE
LEVELS CAN CAUSE PERMANENT HEARING IMPAIRMENT OR LOSS. USER CAUTION IS ADVISED AND EAR PROTECTION IS RECOMMENDED IF UNIT IS OPERATED AT HIGH VOLUME.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
"IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL" “ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES.” "REFERREZ-VOUS AU MANUAL D'UTILISATION" "UNBEDINGT IN DER BEDIENUNGSANLEITUNG NACHSCHLAGEN"
EXPLANATION OF GRAPHICAL SYMBOLS: EXPLICACION DE SIMBOLOS GRAFICOS: EXPLICATION DES SYMBÔLES GRAPHIQUES:
"DANGEROUS VOLTAGE" “VOLTAJE PELIGROSO” "DANGER HAUTE TENSION" "GEFAHLICHE SPANNUNG"
=
=
ATTENTION
RISQUE D'ELECTROCUTION
NE PAS OUVRIR
ATTENTION: POUR REDUIRE D'ELECTROCUTION NE PAS
ENLEVER LE COUVERCLE. AUCUNE PIECE INTERNE N'EST REPRABLE
PAR L'UTILISATEUR. POUR TOUTE REPARATION, S'ADRESSER A UN
TECHNICIEN QUALIFIE.
VORSICHT
ELEKTRISCHE SCHLAGGEFAHR
NICHT OFFENEN
VORSICHT: ZUR MINIMIERUNG ELEKTRISCHER SCHLAGGEFAHR NICHT
DEN DECKEL ABENHMEN. INTERNE TEILE KONNEN NICHT VOM
BENUTZER GEWARTET WERDEN. DIE WARTUNG IS QUALIFIZIERTEM
WARTUNGSPERSONAL ZU UBERLASSEN.
TOP PANEL:
BA-110 BASS AMPLIFIER
0dB
-15dB
Contour
Headphones
Line Out
CD Input
On
1. 0dB INPUT :Connect your “passive” bass guitar here by means of a shielded instru­ment cable. This input is not padded and is best suited for basses without active elec­tronics or “hot” pickups.
2. -15dB INPUT : Connect your “active” bass here by means of a shielded instrument cable. This input is padded 15dB and is best suited for basses with active electronics and/or “hot” pickups.
3. VOLUME: Use this control in conjunction with your instrument’s volume controls to adjust the output level of the amplifier. The BA-110 employs a built in limiter to keep the output clean at full power, however, extreme settings may cause some audible distortion.
4. CONTOUR: This switch, when de­pressed, boosts the high and low frequen­cies while cutting the midrange to provide a “funk” slap-bass tone.
5. LOW: Use this control to adjust the low frequency level of the amplifier. This control has a 28dB range at 100Hz.
6. MID: Use this control to adjust the midrange level of the amplifier. This control has a 26dB range at 600Hz.
7. HIGH: Use this control to adjust the high frequency level of the amplifier. This control has a 35dB range at 10kHz.
8. CD INPUT: Use these RCA jacks to con­nect the line level (or headphones) output of
a CD player or tape deck. The two jacks sum the stereo signal into a mono signal which is fed into the BA-110 just prior to its power amplifier. Use the volume control on the CD or tape player to control the level of this signal.
9. LINE OUT: This jack supplies a post-eq, unbalanced line level signal for connecting to a house sound board, recording unit or external amplifier. The level of this signal is controlled by the Volume control (#3).
10. HEADPHONES: For private practice sessions, plug headphones into this jack. The internal speaker is disconnected when the headphones jack is used.
11. ON LED: This LED illuminates when the amplifier is plugged in and turned on.
12. POWER: Use this switch to turn the amplifier on and off – the top of the switch is depressed in the on position.
13. POWER CORD (rear panel, not shown): Use this cord to connect the
amplifier to a suitable source of A.C. volt­age. This is a grounded, three-wire cord and must be connected to a properly grounded outlet. DO NOT attempt to
defeat the ground connection of the power cord! If your amp was purchased
outside of the United States, see the stick­er next to the A.C. connector for its power ratings. Follow the above guidelines.
5
6
0dB
Input
-15dB
4
3
1
010
7
8
9
2
Volume Low Mid High
Contour
4
3
2
1
010
1 2 3 4 5 6 7 8 9 10 1211
5
6
7
8
9
5
4
3
2
1
010
5
6
7
9
4
3
8
2
1
010
6
7
8
9
Headphones
CD Input
Line Out
On
Power
www.ampeg.com
Ampeg is proudly Made in America.
©2000 SLM Electronics, 1400 Ferguson Avenue, St. Louis, MO 63133 U.S.A.
TECHNICAL SPECIFICATIONS:
OUTPUT POWER RATING 30 Watts at 4 ohms MAX INPUT LEVELS 0dB Input: 800mV RMS
-15dB Input: 5V RMS CD Input: 2V RMS
LINE OUT LEVEL 2.15V RMS HEADPHONE OUT LEVEL 1.35V RMS GAIN 40dB CONTOUR 10dB boost @ 50Hz
5dB cut @ 600Hz 10dB cut @ 10kHz
HIGH 35dB range @10kHz MID 26dB range @600Hz LOW 28dB range @100Hz SPEAKER SPECS 10”, 30 w, 4 ohm, 1.5” voice coil dia., 22 oz. magnet POWER REQUIREMENTS 120VAC, 60Hz, 36VA
100/115VAC, 50/60Hz, 36VA 230VAC, 50/60Hz, 36VA
SIZE AND WEIGHT 15” W x 16” H x 12” D; 32 lbs.
Ampeg continually develops new products, as well as improves existing ones. For this reason,
the specifications and information in this manual are subject to change without notice.
47-637-01 • 09/00
0dB
INPUT
-15dB
INPUT
VOLUME
MIXER
SPEAKER
STYLE
LOW MID HIGH
CD
INPUTS
TONE CIRCUITS
LIMITER
& POWER AMP
LINE OUT
HEAD PHONES
L
R
SYSTEM BLOCK DIAGRAM:
BA-110 BASS AMPLIFIER
Loading...