Amped Wireless AP300 User Manual

SETUP GUIDE

— R E A D F I R S T —

?

Need Help? Give us a call.

Phone: [phone]
Email: [e-mail]
Web: www.ampedwireless.com/support

High Power Wireless-300N Smart Access Point

Connect the Smart Access Point to your Router

1

Connect to

Network Port

2

Scan for available wireless networks on your
PC and connect to the following network:

Connect your Computer to the Smart Access Point

(LAN Port)

Attach the Antennas

Plug in the Power Adapter

Connect the Smart Access Point
to your Router’s Network (LAN)
port, or a network switch.

InternetModemRouter

Allow up to two (2) minutes for the
Smart Access Point to automatically
configure itself to your network

Wired Connections:Wireless Connections:

Attach any Wired Devices to the
Smart Access Point using an
Ethernet cable.

AP300

Network

NETWORK ID: Amped_AP

PASSWORD: wireless

Congratulations, you’re done!

The instructions below are optional. You may now use your Smart Access Point without any additional
configurations. However, if you wish to change any settings (such as network ID and security) for the

!

Note: If your network uses static IP address assignments, you will need to manually configure the settings for your
Smart Access Point. See the instructions on the back to access the configuration menu of the Access Point.

1

Smart Access Point, follow the instructions below to access the configuration menu of the Access Point.

Optional Configurations: Accessing the Settings Menu

Scan for available wireless networks on your
PC and connect to the following network:

NETWORK ID: Amped_AP

PASSWORD: wireless

Amped_AP

2

3

Open your Web Browser

Welcome to the Smart Setup Wizard

Do NOT use an Ethernet cable when accessing the setup menu.

!

Enter the setup web address into your browser:

http://setup.ampedwireless.com

If the URL fails to open, then try: http://192.168.1.240

The wizard will guide you through the
setup of your:

1) System Clock

1

2

2) Wireless Network SSID

3

3) Wireless Network Security Key

Set the System Clock Time

4

5

Wireless Network ID

Click Start to begin.

The System Clock is used for system logs
and setting schedules for Internet access.
Click Sync to synchronize the System Clock
with the time on your computer.

Click Next to continue.

The ID of your Wireless Network is:

Amped_AP

6

Wireless Network Security

To change it, enter a new name in the SSID
field. Users connecting wirelessly to the
Access Point will use this ID to identify your
wireless network.

Click Next to continue.

The default Security Key (WPA) of your
wireless network is: wireless

To change it, enter a new key in the Secu­rity Key field. The key must be at least 8
characters long.

Setup Summary

7

Click Next to apply your settings.

The Smart Access Point will reboot. This
process may take up to 2 minutes. The page
will automatically reload after the count­down. If it does not, you may need to
reconnect to the Access Point and refresh
the page manually.

The Setup Summary provides you with
information regarding your current settings.

If you have wired network devices, you may
attach them to the wired ports on the back
of the Smart Access Point for additional
wired connectivity.

If you have any questions during the setup process
please contact Amped Wireless support department:

Phone: [phone]
Email: [e-mail]
Web: www.ampedwireless.com/support

If you have any questions regarding this product, then give us a call we’re here to help: 888-573-8820

This is the second page of the Setup Guide. Start on the opposite side first.

How to Connect your Computer Wirelessly to the Smart Access Point:

Windows 7 and Vista

A. Click on the Wireless icon to see available
wireless networks (For Vista, click Start >
Connect To). Select the "Amped_AP"
network and click Connect.

Amped_AP

Mac OS X

A. Click on the Wireless icon to see available
wireless networks. Select the "Amped_AP"
network and click Connect.

B. When prompted, enter the wireless
security key “wireless” and click OK.

B. When prompted, enter the wireless
security key “wireless” and click OK.

Amped_AP

Amped_AP

Wi-Fi Protected Setup (One Touch Setup or Push Button Configuration)

If your wireless adapter has WPS one-touch setup you can use it when connecting to the Smart
Access Point. Hold down the WPS button on the Smart Access Point (back panel) for 3 seconds. The
WPS LED will begin to blink. As it blinks, push the WPS button on your wireless adapter or enable
WPS with the provided software for your wireless adapter.

Using the Smart Features on your Smart Access Point

The Smart Access Point is equipped with many powerful security features which can be
accessed through the web menu under More Settings > Smart Features on the left side of
the web menu:

12:26

?

Web Menu (Left Side)

If you are unfamiliar or want more information on how to setup Smart Features, please refer
to the Users Manual on the included CD.

Wireless Access Scheduling

Control when your WiFi is on/off

Menu Location: More Settings > Smart Features > Access Schedule

User Access Control

Restrict network access to specific users

Menu Location: More Settings > Smart Features > User Access

Wireless Coverage Control

Adjust the distance of your wireless network

Menu Location: More Settings > Smart Features > Wireless Coverage

Setting a Static / Manual IP for your Smart Access Point

If your network uses Static IP settings, you will need to set a static IP address for your
Smart Access Point. To do this, access the More Settings > IP Settings menu from the
navigation menu and select Disabled from the DHCP drop down menu. Next enter the IP
information as it relates to your network. Click Apply and reboot when you are done.

Using Power over Ethernet (Optional)

Power-over-Ethernet (PoE) allows you to use the Smart Access Point without a power
adapter. The power for the Smart Access Point is provided through the Ethernet cable
(PoE Ethernet cable required) that is connected to another PoE device (such as an AP300).

To use PoE, simply attach a PoE-ready cable to the Smart Access Point from a PoE ready
device such as another Smart Access Point AP300, as shown below:

Additional Access Points

Power Adapters NOT Required

PoE Ethernet Cable

(sold separately)

Non-PoE Cable

Four (4) wires.

Internet Modem Router

How to identify a PoE Ethernet Cable
by looking at the connectors:

Main Access Point

Power Adapter Required

PoE Ethernet Cable

(sold separately)

PoE Cable

Eight (8) wires.

Tips on using Power over Ethernet with the Smart Access Point

a. Pre-configure the Smart Access Point before Setup:

Configure the wireless network names (SSID), security settings and channel numbers for each Smart
Access Point before beginning your physical installation. This will make it easy to identify each wireless
network as it is installed. Do not use the same name for each Smart Access Point as this will cause

confusion within the network.

b. Proper Network Port Connections
Attach the PoE cable from the Wired Devices Port of the first Smart Access Point (using a power adapter)
to the Network Port of the second Smart Access Point (using only PoE and no power adapter).

c. Allow the Smart Access Point time to Register with your Network:
After attaching the second Smart Access Point, wait 2 minutes for the second Smart Access Point (using
PoE) to auto-configure itself to the network. You will know when registration is complete when the
wireless network name of the second Smart Access Point appears in a SSID scan from a computer.

d. Repeat if Needed:

Repeat the steps above if you have additional Smart Access Points that you wish to daisy chain using PoE.

Troubleshooting Tips

Problem: I entered http://setup.ampedwireless.com and it failed to open the Web Menu

a. Make sure your computer is connected to the Smart Access Point wirelessly and NOT using a network cable. Ensure
the power is plugged in and on. Try to access the setup menu again.
b. Enter the following web address into your web browser instead of ‘setup.ampedwireless.com’: http://192.168.1.240
c. Power off (unplug the power adapter) the Smart Access Point and power it back on. Try again.
d. Reset your Smart Access Point to default settings by holding the Reset Button (located on the back panel) for ten (10)
seconds and try again.

Problem: I do not have Internet access when connecting to the Smart Access Point

a. Your router or original network may not have Internet access. First check to see if you are able to access the Internet
by connecting directly with your router. If you cannot, there is a problem with your router that needs to be fixed first.
If you are able to access the internet, continue with the following troubleshooting options below.
b. Your router may be using Static IP assignments. If so, you will need to configure a Static IP for the Smart Access Point.
Connect your PC to the Smart Access Point using an Ethernet cable. Disconnect your PC from any wireless networks
that it may be connected to. Access the web menu at setup.ampedwireless.com using a web browser. Access the IP
settings menu from the left hand navigation bar. Select ‘Disabled’ under the DHCP dropdown menu and enter an IP
address that matches your router’s IP settings.

If you have any questions regarding this product, then give us a call we’re here to help: 888-573-8820

Amped Wireless

A Division of Newo Corporation
Copyright © 2011 Amped Wireless / Newo Corporation. All rights reserved.
Amped Wireless, Newo Corporation, the Amped Wireless Logo are registered trademarks or trademarks of Newo Corporation.