Communication Ports
The Terminal Charger also has 2 communication ports: RS-232 (DB-9) and USB
(Type II). The Terminal Charger uses a standard RS-232 (DB-9 Male – DB-9
Female) cable with a length of 3 Meters or less.
Both communication connectors on the back of the universal terminal charger
are wired “straight through”. This means that the communication settings on
the handheld terminal will determine the settings on the terminal charger. The
Terminal Charger has no internal or external settings that can be changed.
The full-speed USB or RS-232 communication port can be used for uploading
and downloading of data files to the handheld terminal. These ports can also
be used to load a new or updated operating system into the handheld
terminal.
DB-9 Pin out (RS-232)
1 – DCD (Data Carrier Detect) 6 – DSR (Data Set Ready)
2 – RXD (Receive Data) 7 – RTS (Request To Send)
3 – TXD (Transmit Data) 8 –CTS (Clear To Send)
4 – DTR (Data Terminal Ready) 9 – NC (No Connection)
5 - GND (Signal Ground)
Regulatory Information
All American Microsystems, Ltd. devices are designed to be compliant with
rules and regulations in locations they are sold and will be labeled as required.
Any changes or modifications to American Microsystems, Ltd. equipment, not
expressly approved by American Microsystems, Ltd., could void the user's
authority to operate the equipment.
Power Supply
Use only an American Microsystems, Ltd. approved Power Supply, output rated
5 VDC and minimum 2.8A. The Power Supply is certified to EN60950.
Disclaimer
American Microsystems, Ltd. reserves the right to make changes in specifications and other information contained in this document without prior notice,
and the reader should in all cases consult American Microsystems, Ltd. to
determine whether any such changes have been made. The information in this
publication does not represent a commitment on the part of American
Microsystems, Ltd.
American Microsystems, Ltd. shall not be liable for technical or editorial errors
or omissions contained herein; nor for incidental or consequential damages
resulting from the furnishing, performance, or use of this material.
This document contains proprietary information that is protected by
copyright.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated into another language without the prior written
consent of American Microsystems, Ltd.
FCC Declaration of Conformity
Product Name: Terminal Charger
Model Number: ACC-5925
Radio Frequency Interference Requirements
This equipment complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This equipment may not cause harmful
interference, and (2) this equipment must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a residential environment. This equipment generates
uses and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If you determine the equipment does cause
harmful interference to radio or television reception (this may be determined
by monitoring the interference while turning the equipment off and on), you
are encouraged to try to correct the interference by one of the following
measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
· Consult the dealer or an experienced radio or TV technician for help.
Radio Frequency Interference Requirements - Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.
ACC-5925
Terminal Charger
2190 Regal Parkway • Euless, TX 76040
© 2013 AML
800.648.4452 • Local: 817.571.9015
Marking and European Economic Area (EEA)
Products intended for sale within the European Union are marked
with the CE mark which indicates compliance to applicable
Directives and European Normes (EN), as follows. Amendments to
these Directives or EN’s are included.
· Electromagnetic Compatibility Directive 89/336/EEC
· Low Voltage Directive 73/23/EEC
2190 Regal Parkway • Euless, TX 76040
© 2013 AML
800.648.4452 • Local: 817.571.9015
User’s Guide
www.amltd.com • 800.648.4452
© 2013 AML
Introduction
The ACC-5925 Terminal Charger charges any AML M7225, M7220, M71V2, or
M5900 Series handheld terminal, along with one spare battery.
About This Guide
This guide provides instruction on setting up and using the ACC-5925 Terminal
Charger.
To connect power to the cradle:
1. Plug-in the Power Supply to a standard AC electrical outlet.
2. Connect the Power Supply Plug to the barrel power jack on the cradle.
3. The cradle LED’s will turn green to indicate that power is available.
4. The LED’s remain green until a terminal or battery is inserted into the slots.
The Terminal Charger
The cradle automatically charges the terminal battery while it is resting in the
cradle. The cradle also includes an extra slot to charge a spare battery. The
Terminal Charger can accommodate the terminal with or without the optional
pistol grip handle.
Set Up
Setting up the cradle includes unpacking, connecting the power cable, and
mounting the cradle on a table top.
Unpacking the Cradle
The shipping box includes the following:
· One ACC-5925 Terminal Charger
· One PWR-7100 Power Supply (120VAC)
or PWR-7150 (220VAC)
· One Line Cord with PWR-7150
· This User’s Guide.
If any parts are missing or damaged, contact your authorized Customer
Support Representative immediately. Save the shipping box for storing or
shipping.
Connecting the Power
The PWR-7100 power supply is included with the ACC-5925 Terminal Charger
for 120VAC. The PWR-7150 power supply is included with the ACC-5925
Terminal Charger for 220VAC, along with a country specific line cord.
Use only an American Microsystems, Ltd. approved power supply rated at 5
VDC at a minimum of 2.8 Amps. The power supply connects to the ACC-5925
by a 2.1mm x 5.5mm, barrel center-positive connector.
Charging
For wireless handhelds, turn the terminal off and insert it into a cradle slot for
an optimum charge. It begins to charge as soon as it is inserted.
Batch collection devices, including the M5900 series terminals, should be
charged while powered on. These units will automatically power on if inserted
into the ACC-5925 when in off or suspended modes.
Indicator Lights
LED Color Description
Off No power supplied to terminal charger.
Green If no terminal is present in the charger, green indicates that
there is power available. If terminal is present, green
indicates that the terminal is fully charged.
Red Terminal or battery is present in the terminal charger and the
battery is being charged.
Troubleshooting
Symptom
LED does not light when
the terminal charger is
powered on.
LED stays green when the
terminal is inserted.
LED stays red for more
than 6 hours.
Cause
Terminal charger is not
receiving power.
Terminal is not seated
firmly in the terminal
charger, or the battery is
not properly installed in
the terminal.
Battery is charged.
Battery faulty and can not
be charged.
Suggested Action
Make sure the power
supply is securely
connected and receiving
po wer.
Make sure the battery is
properly installed in the
terminal, and reseat the
terminal in the terminal
charger.
Normal status.
Replace battery with an
AML approved battery.
Spare Battery
The Terminal Charger has three indicator lights:
- Indicates that the terminal charger is plugged in.
- Indicates the terminal main battery is charging.
2190 Regal Parkway • Euless, TX 76040
© 2013 AML
800.648.4452 • Local: 817.571.9015
2190 Regal Parkway • Euless, TX 76040
© 2013 AML
800.648.4452 • Local: 817.571.9015
- Indicates the spare battery is charging.
When the battery charging LED is red, the battery is charging. When the battery
charge LED is green, the battery is fully charged. A fully discharged battery
takes about 6 hours to completely recharge.
2190 Regal Parkway • Euless, TX 76040
© 2013 AML
800.648.4452 • Local: 817.571.9015
Loading...