AMETEK XG 850 Watt Series Quick Start 1.09 and earlier User Manual

QUICK REFERENCE GUIDE: XG 850 Watt Series Programmable DC Power Supply (firmware v1.09 and below)

The XG is equipped with a rotary Adjust/Enter control to provide a streamlined front panel for faster setup. Set voltage and current quickly and easily using the rotary Adjust/Enter control and the 9-position Mode control. The information provided in this Quick Reference Guide is for basic usage of the front panel and for understanding the menu system. See the other side of this Quick Reference Guide for a map of the front panel menu system. For complete information on the XG, please refer to the XG 850 Watt Series Programmable DC Power Supply Operating Manual (Part number: M370078-01).

1. Rotary Adjust/Enter Control

2. Constant Voltage Mode LED

3. Model Identification Label

4. Output Voltage Display

5. Constant Current Mode LED

6. Output Current Display

7. Alarm Indicator LED

8. Output On/Off Button

9. AUX On/Off Button

10.l 9-position Mode Control

VOLTS: Voltage Programming AMPS: Current Programming FLD: Foldback PRT: Protection SAV: Save User Setting Memory Locations RCL: Recall User Setting Memory Locations CAP: Current Analog Programming VAP: Voltage Analog Programming PGM: Programming

XG Front Panel Controls, Displays, and Indicators XG Rotary Adjust/Enter Control

General Procedures for Setting Up Features

• To select a mode, rotate the 9-position Mode control to the desired mode.

• To select the feature or setting, turn the rotary Adjust/Enter control to scroll through the different available settings of that mode.

• The settings appear on the output display.

• Press the rotary Adjust/Enter control to select the feature or setting.

• Set each value using the rotary Adjust/Enter control. When the value has been selected, press the Adjust/Enter control to commit the

updated value.

Setting the Output Voltage and Current Limit Using Tracking Mode

To access the tracking mode where new values take effect as the rotary Adjust/Enter control is turned:

1. Select VOLTS or AMPS on the 9-position Mode control. The set point will blink and the unit will be in coarse tracking mode.

• When VOLTS mode is selected, the voltage set point will blink in the output voltage display.

• When AMPS mode is selected, the current set point will blink in the output current display.

2. Use the rotary Adjust/Enter control to adjust the set point.

3. Press the Adjust/Enter control to use fine adjust tracking mode. The set point blinks faster when the unit is in fine tracking mode.

4. Use the rotary Adjust/Enter control to fine tune the set point.

5. Once the set point has been selected, press the Adjust/Enter control to exit tracking.

Front Panel Menu System (firmware v1.09 and below) Front Panel Display Messages

)

VOL

CUR

FLD

PRT

SAV

RCL

CAP

VAP

PGM

Coarse CurrentTracking

CV CC

None

OVP UVP

Overheat Protection

Shutdown Logic

Select Preset

Off

Voltage Isolated

Voltage Non-Isolated

Resistive Isolated

Resistive Non-Isolated

Off

Voltage Isolated

Voltage Non-Isolated

Resistive Isolated

Resistive Non-Isolated

USB LAN

GPIB RS-232 RS-485

Slave Address (1-30)

Local Lock

Fold Delay Fold Delay

OVP CoarseAdjust OVP FineAdjust UVP CoarseAdjust UVP Fine Adjust

On/Off

1/0

Current APG Level Current APG Level Current APG Level Current APG Level

VoltageAPG Level VoltageAPG Level VoltageAPG Level

VoltageAPG Level

Address (1-30) Address (1-30) Address (1-30)

Data Rate Data Rate

On/Off

Coarse Volt Pre-SetCoarse Volt Tracking

Coarse Current Pre-Set

Legend:

Press rotaryAdjust/Enter control

when no modification of the tracking value has been made.

Press rotaryAdjust/Enter control

Rotate rotaryAdjust/Enter control

Address (1-30) Address (1-30)

Fine Volt Pre-SetFine Volt Tracking

Fine Current Pre-SetFine Current Tracking

Mode Control State

Setting/Value

0 1 AnPR AS AvAS CAPr CLr CC COn7 CU CRPC CrPU CShr Curr CUrrShAr deLa FOLD FLA FNPC FNPU FLd gpib HbPS In H rS LE C LE U Loc LOCL OCP O7P OUP OvPF OUPC OU7P POL PRO PSU r IS rCL RE rnIs SAFE Sd sLa

S rS U Is UN Is UUP UUPF UAPr UOL

Negative Polarit Positive Polarit Analog Programmin Power On Autostart Auxiliary Autostart Current Analog Programmin Clea Constant Current Controlle Constant Voltage Coarse Current Pre-set Mode Coarse Voltage Pre-set Mode Current Share (same as CUrrShAr Current Current Share (same as CShr Fold Dela Foldback protection triggered Flash Fine Current Pre-set Mode Fine Voltage Pre-set Mode Setting up Foldback trigge GPIB Interface Data rate (Kbps Interlock Hard Reset Current APG Level Voltage APG Level Lock Local Over Current Protection Over Temperature Protection Over Voltage Protection Over Voltage Protection fine adjustment OVP Calibration Output Protection Polarit Protection mode Power Supply Unit Isolated Resistive Analog Programmin Recall User Setting Memory Locations Remote Programming/Interface Non-Isolated Resistive Analog Safe Shutdown Slave Remote Interface Soft Reset Isolated Analog Voltage Programmin Non-Isolated Analog Voltage Under Voltage Protection Coarse Under Voltage Protection Fine Adjustment Voltage Analog Programmin Voltage