Ametek ATC-125, ATC-140, ATC-156, ATC-157, ATC-250 Data sheet

...
t e m p e r a t u r e
Accessory Sheet AS-CP-2205-US
Insertion tubes
for JOFRA temperature dry-blocks
Inserts for JOFRA dry-blocks:
ITC-155 -23 to 155°C / -9 to 311°F ITC-320 33 to 320°C / 91 to 608°F ITC-650 33 to 650°C / 91 to 1202°F
CTC-140 -17 to 140°C / -1 to 284°F CTC-320 33 to 320°C / 91 to 608°F CTC-650 33 to 650°C / 91 to 1202°F CTC-1200 300 to 1205°C / 572 to 2200°F
MTC-140 -17 to 140°C / -1 to 284°F MTC-320 33 to 320°C / 91 to 608°F MTC-650 33 to 650°C / 91 to 1202°F
Page 1:
Does and don’ts in the use of inserts
Page 2:
Using inserts
Page 3:
Inserts for CTC and MTC series
Page 4-5:
Predrilled inserts for ATC and ITC series
Page 5:
Undrilled inserts for ATC and ITC series
Page 6-7:
Multi-hole inserts for ATC and ITC series
Page 8:
Application kit for calibration of sanitary sensors
PRODUCT DESCRIPTION
From time to time we get informa­tion from end-users of JOFRA dry­block calibrators that something is wrong with the calibrator, as it is not able to meet the temperature specifications.
This is often due to the fact that the customer is using a wrong insertion tube, although he is in good faith.
Therefore, you can save a lot of time and irritations by using the right insertion tube.
Does and dont´s in the use of inserts
Important things to REMEMBER when using inserts:
Remove inserts from the well with the insert removal tool.
Remove the inserts after calibration, as it might cause problems to remove them later on if they stay in the well for longer periods.
Take care when removing very hot or cold inserts and use adequate
protective equipment if necessary.
Make certain that the sensors and inserts are free from any particles of dirt before inserting them into the well. Inserts are designed to fit perfectly into the well thus maximizing the thermal conductivity. If not the insert may be jammed.
Remove regularly build-up of dirt and dust from inserts and wells with a cloth or detergent.
Important things to AVOID when using inserts:
Do not force inserts or sensors into the well.
Do not drop any foreign materials into the well.
Do not use oil or other liquids to optimise the thermal conductivity
due to risk of leakage, which will destroy the other components.
Do not use inserts of metals dissimilar to that of the block, unless specified by the manufacturer as this may cause a different degree of expansion and contraction.
ISO 9001 Manufacturer
Sensor-under-test
Calibrator
Insertion tube
Well
Sensor-under-test
Calibrator
Insertion tube
Well
Sensor-under-test
Calibrator
Insertion tube
Well
Sensor-under-test
Calibrator
Insertion tube
Well
Sensor-under-test
Insulation plug
Calibrator
Insertion tube
Well
Sensor-under-test
Calibrator
Insertion tube
Well
USING INSERTS
Insertion tubes for temperature dry-blocks
Using inserts from other JOFRA calibrators
Often customers believe that they can use inserts from other models of JOFRA tem­perature calibrators. Consequently, we get complaints about errrors in the tempera­ture specifications.
Even if the diameter is right, the length might not be. In this case the insertion tube is too tall. This gives a heat flow out of the top of the well and the temperature unifor­mity will change dramatically.
Using inserts that are too small
Using insertion tubes with diameters that are too small creates another problem. The heat transfer between the well and the insertion tube is insufficient, as the air around the tube has an insulating effect. This will make the temperature very unstable and unable to reach the set value.
This problem also applies to the use of 6 mm and 1/4 in (6.35 mm) sensor holes. Even though this combination may seem to match it gives a very poor heat transfer as the sensors do not have an even contact with the insertion tube.
Accessory Sheet AS-CP-2205-US
Using inserts made of the “wrong” material
Home-made inserts can be made in a very professional way with the correct lenght and size, but the material used for the inserts might cause problems and wrong results. If the specifications e.g. apply to a brass insert, it is not a good idea to use inserts made of aluminum or other materials due to the difference in conductivity.
To get the right result and to make the calibrator measure correctly, it is therefore extremely important to use the right material for the inserts.
Using inserts with too short sensor holes
When drilling your own inserts it is a common mistake to make the sensor holes too short. Using this kind of insert may influence the temperature gradient, as the calibra­tor was originally calibrated at the bottom of the well.
Using inserts without using an insulation plug
All JOFRA cooling temperature calibrators are delivered with an insulation plug, to be placed on top of the well. The design of this type of calibrators require such a device, and the calibrators have also been calibrated with the insulation plug.
There is a large heat flow out of the well, and if the plug is not used during calibration, it will cause problems reaching the set temperature of the calibrator.
2 www.jofra.com
Using inserts with the correct size, holes and material
To avoid problems, waste of time and to get the optimum use of your calibrator we recommend that you use inserts from AMETEK Calibration Instruments as they follow our specifications.
Insertion tubes for temperature dry-blocks
PREDRILLED INSERTS FOR CTC AND MTC SERIES
Inserts for CTC-140 A and CTC-320 A/B are made of aluminum. Inserts for CTC-650 A/B are made of brass. Inserts for CTC-1200 A are made of high-temperature steel alloy. All specifications on hole sizes are referring to the outer diameter (OD) of the sensor-under-test. The correct clearance size is applied in all predrilled inserts.
Inserts, undrilled
Instruments
Inserts CTC/MTC-140 A 2CTC/MTC-320 A CTC/MTC-650 A CTC-320 B CTC-650 B CTC-1200 A
5-pack, undrilled inserts
Undrilled insulation plug
Spare part no. for predrilled inserts - metric (mm)
Probe diameter
3 mm 003
4 mm 004
5 mm 005
6 mm 006
7 mm 007
8 mm 008
9 mm 009
10 mm 010
11 mm 011
12 mm 012
13 mm 013
14 mm 014
15 mm 015
16 mm 016
18 mm 018
20 mm 020
Package of the above inserts
Multi-hole type 1 M01
Spare part no. for predrilled inserts - imperial (inch)
Probe diameter
1/8 in 125
3/16 in 187
1/4 in 250
5/16 in 312
3/8 in 375
7/16 in 437
1/2 in 500
9/16 in 562
5/8 in 625
11/16 in 688
3/4 in 750
13/16 in 813
7/8 in 875
Package of the above inserts
Multi-hole type 2 M02
Note 1: Use the insert code, when ordered as the standard insert together with a new calibrator. Note 2: CTC-140 A only: Remember to use matching insulation plugs. Note 3: CTC-140 A only: All multi-hole inserts are delivered with a matching insulation plug. Note 4: CTC-1200 A only: Remember to order matching insulation plugs.
60F448 100175 100194 60F356 60F420 124403
123937 N/A N/A N/A N/A see below
Instruments
Insert
code
Insert
code
CTC/MTC-
1
140 A
123428 123436 123444 N/A N/A 124503
60F451 100177 100196 60F359 60F423 124406
123429 123437 123445 123452 123460 124504
60F453 100179 100198 60F361 60F425 124407
123430 123438 122516 123453 123461 124505
105185 100182 100201 105190 105195 124506
105186 100183 100202 105191 105196 124507
105187 100185 105188 105192 105197 124508
123431 100188 100204 105193 105198 124509
123432 100186 100206 105194 105199 124510 124414
123433 60F339 105189 123454 123462 N/A
N/A 100190 100208 123455 123463 N/A
N/A 100191 100209 123456 123464 N/A
N/A 123439 123446 123457 123465 N/A
N/A 123440 122517 123458 123466 N/A
N/A 123441 122518 123459 123467 N/A
124679 124681 124685 124683 124687 124689
123479
CTC/MTC-
1
140 A
60F450 100176 100195 60F358 60F422 124511 124415
60F452 100178 100197 60F360 60F424 124512
60F454 100180 100199 60F362 60F426 124404
60F456 100181 100200 60F364 60F428 124513 124518
60F458 100184 100203 60F366 60F430 124514
60F460 100187 100205 60F368 60F432 124515
60F462 100189 100207 60F370 60F434 124405 124414
60F464 60F344 60F408 60F372 60F436 N/A
60F466 100192 100210 60F374 60F438 N/A
N/A 60F348 60F412 60F376 60F440 N/A
N/A 100193 100211 60F378 60F442 N/A
N/A 60F352 60F416 105184 60F444 N/A
N/A 60F354 60F418 60F377 60F446 N/A
124680 124682 124686 124684 124688 124690
123480
CTC/MTC-
2
320 A
3
123475 123476 N/A N/A N/A
CTC/MTC-
2
320 A
3
123477 123478 N/A N/A N/A
CTC/MTC-
650 A
CTC/MTC-
650 A
CTC-320 B CTC-650 B
Instruments
CTC-320 B CTC-650 B
CTC-1200 A
Inserts
CTC-1200 A
Inserts
4
Insulation
plugs
124415
124416
124518
124519
N/A
4
Insulation
plugs
124416
124519
N/A
Accessory Sheet AS-CP-2205-US
Undrilled inserts
(CTC/MTC-140 A)
4
4
Undrilled inserts
(CTC/MTC-320 / 650 A/B)
Undrilled inserts
(CTC-1200 A)
3
4
5
Multi-hole type 1
(CTC/MTC-140 A)
9
3
6
Multi-hole type 1
(CTC/MTC-320 A / 650 A)
3/16
1/8
Multi-hole type 2
(CTC/MTC-140 A)
3/8
1/8
1/4
Multi-hole type 2
(CTC/MTC-320 A / 650 A)
www.jofra.com 3
4,5
6
4
5
1/4
3/16
Insertion tubes for temperature dry-blocks
Accessory Sheet AS-CP-2205-US
PREDRILLED INSERTS FOR ATC AND ITC SERIES - 4 MM REFERENCE HOLE
JOFRA dry-block insert compatibility and materials: ATC-320 = ATC-650 = ITC-320 = ITC-650 (made of brass) ATC-125 = ATC-155 = ATC-156 (made of aluminum) ATC-157 = ITC-155 (made of aluminum) All specifications on hole sizes are referring to the outer diameter (OD) of the sensor-under-test. The correct clearance size is applied in all predrilled inserts.
Spare part no. for predrilled inserts with 4 mm reference hole
Instruments
Probe diameter
3 mm
4 mm
5 mm
6 mm
7 mm
8 mm
9 mm
10 mm
11 mm
12 mm
13 mm
14 mm
15 mm
16 mm
Package of the above inserts
Set of insulation plugs for 4 mm reference hole
Spare part no. for predrilled inserts with 4 mm reference hole
Probe diameter
1/8 in
3/16 in
1/4 in
5/16 in
3/8 in
7/16 in
1/2 in
9/16 in
5/8 in
Package of the above inserts
Set of insulation plugs for 4 mm reference hole
Insert
code
003 105623 105623 123270 105622 123270
004
005
006
007
008
009
010
011
012
013
014
015
016
Insert
code
125
187
250
312
375
437
500
562
625
ATC-125 A/B
1
105625 105625 123271 105624 123271
105627 105627 123272 105626 123272
105629 105629 123273 105628 123273
105631 105631 123274 105630 123274
105633 105633 123275 105632 123275
105635 105635 123276 105634 123276
105637 105637 123277 105636 123277
105639 105639 123278 105638 123278
105641 105641 123299
105643 105643 123300
105645 105645 N/A 105644 N/A
105647 105647 N/A 105646 N/A
105649 105649 N/A 105648 N/A
- 124697 124697 124699 124701 124699
- 126234 105810 123374 N/A N/A
ATC-125 A/B
1
105677 105677 123279 105676 123279
105679 105679 123280 105678 123280
105681 105681 123281 105680 123281
105683 105683 123282 105682 123282
105685 105685 123283 105684 123283
105687 105687 123301
105689 105689 123302
105691 105691 N/A 105690 N/A
105693 105693 N/A 105692 N/A
- 124698 124698 124700 124702 124700
- 126234 105810 123374 N/A N/A
ATC-155/156
A/B
ATC-155/156
A/B
ATC-157 A/B
Instruments
ATC-157 A/B
ATC-320/650 A/B
ITC-320/650 A
2
2
ATC-320/650 A/B
ITC-320/650 A
2
2
ITC-155 A
105640 123299
105642 123300
ITC-155 A
105686 123301
105688 123302
Note: All inserts (metric and inches) are supplied with a hole for the 4 mm OD reference sensor. Note 1: Use the insert code, when ordered as the standard insert together with a new calibrator. Note 2: ATC-157 / ITC-155: 12 mm, 13 mm, 7/16 in and 1/2 in inserts are delivered without the 4 mm reference hole, but supplied with a matching insulation plug.
4
(ATC-157 A/B and ITC-155 A)
2
2
4
(ATC-125/155/156/320/650 A/B
and ITC-320/650 A)
2
2
ATC-series
4 www.jofra.com
Insertion tubes for temperature dry-blocks
Accessory Sheet AS-CP-2205-US
PREDRILLED INSERTS FOR ATC AND ITC SERIES - 1/4 INCH REFERENCE HOLE
Spare part no. for predrilled inserts with 1/4 in (6.35 mm) reference hole
Instruments
Probe diameter
3 mm
4 mm
5 mm
6 mm
7 mm
8 mm
9 mm
10 mm
11 mm
12 mm
13 mm
14 mm
15 mm
Package of the above inserts
Set of insulation plugs for 1/4 in. reference hole
Spare part no. for predrilled inserts with 1/4 in (6.35 mm) reference hole
Probe diameter
1/8 in
3/16 in
1/4 in
5/16 in
3/8 in
7/16 in
1/2 in
9/16 in
Package of the above inserts
Set of insulation plugs for 1/4 in. reference hole
Inser t
code
803 125260 125260 125290 125259 125290
804 125262 125262 125291 125261 125291
805 125264 125264 125292 125263 125292
806 125266 125266 125293 125265 125293
807 125268 125268 125294 125267 125294
808 125270 125270 125295 125269 125295
809 125272 125272 N/A 125271 N/A
810 125274 125274 N/A 125273 N/A
811 125278 125278 N/A 125277 N/A
812 125280 125280 123299
813 125282 125282 123300
814 125284 125284 N/A 125283 N/A
815 125286 125286 N/A 125285 N/A
Inser t
code
901 125297 125297 125314 125296 125314
902 125299 125299 125315 125298 125315
903 125301 125301 125316 125300 125316
904 125304 125304 125317 125303 125317
905 125306 125306 N/A 125305 N/A
906 125308 125308 123301
907 125310 125310 123302
908 125312 125312 N/A 125311 N/A
ATC-125 A/B
1
- 125389 125389 125387 125388 125387
- 126240 125511 125510 N/A N/A
ATC-125 A/B
1
- 125392 125392 125390 125391 125390
- 126240 125511 125510 N/A N/A
ATC-155/156
A/B
ATC-155/156
A/B
ATC-157 A/B
2
2
Instruments
ATC-157 A/B
2
2
ATC-320/650 A/B
ITC-320/650 A
125279 123299
125281 123300
ATC-320/650 A/B
ITC-320/650 A
125307 123301
125309 123302
ITC-155 A
ITC-155 A
Note: All inserts (metric and inches) are supplied with a hole for the 4 mm OD reference sensor. Note 1: Use the insert code, when ordered as the standard insert together with a new calibrator. Note 2: ATC-157 / ITC-155: 12 mm, 13 mm, 7/16 in and 1/2 in inserts are delivered without the 4 mm reference hole, but supplied with a matching insulation plug.
1/4
(ATC-157 A/B / ITC-155 A)
2
2
1/4
(ATC-125/155/156/320/650 A/B
and ITC-320/650 A)
2
2
ITC-series
UNDRILLED INSERTS FOR ATC AND ITC SERIES
Instruments
Inserts ATC-125 A/B
5-pack, undrilled inserts
5-pack, undrilled inserts with a 4 mm hole for the reference probe
5-pack, undrilled inserts with a 1/4 in hole for the reference probe
One undrilled insert
Undrilled insulation plug
122720 122720 123286 122719 N/A N/A
122722 122722 123285 122721 N/A N/A
125288 125288 125313 125287 N/A N/A
N/A N/A N/A N/A 124899 124891
126040 122781 123304 N/A N/A N/A
ATC-155/156
A/B
ATC-157 A/B /
ITC-155 A
ATC-320/650
A/B / ITC­320/650 A
4
ATC-140 A/B ATC-250 A/B
1/4
www.jofra.com 5
Insertion tubes for temperature dry-blocks
MULTI-HOLE INSERTS FOR ATC AND ITC SERIES - METRIC (MM)
Accessory Sheet AS-CP-2205-US
12
8
4
1/4
5
6
11
Multi-hole M01
(ATC-140/250 A/B)
4
6
6
6
Multi-hole M01
(ATC-157 A/B / ITC-155 A)
3
3
3
4
3
3
333
3
4
6
9
4
4
3
6
5
Multi-hole M02
(ATC-157 A/B / ITC-155 A)
6
1/4
6
6
4
4
1/4
4
Multi-hole M01
(ATC-125 A/B)
4
6
1/4
6
6
Multi-hole M02
(ATC-125 A/B)
4
3
3
3
3
1/4
6
3
Multi-hole M03
(ATC-125 A/B)
4
4
4
4
4
4
1/4
4
Multi-hole M01
(ATC-156/320/650 A/B /
ITC-320/650 A)
6
6
4
6
6
1/4
6
6
6
Multi-hole M02
(ATC-156/320/650 A/B /
ITC-320/650 A)
4
3
3
3
3
3
3
3
3
1/4
3
3
3
6
Multi-hole M03
(ATC-156/320/650 A/B /
ITC-320/650 A)
Multi-hole M03
(ATC-157 A/B / ITC-155 A)
4
3
1/4
6
5
Multi-hole M07
(ATC-157 A/B / ITC-155 A)
Multi-hole M06
(ATC-157 A/B / ITC-155 A)
3
3
3
1/4
3
3
3
3
3
Multi-hole M08
(ATC-157 A/B / ITC-155 A)
4
6
5
1/4
9
6
4
Multi-hole M04
(ATC-125 A/B)
4
6
3
9
5
4
Multi-hole M04
(ATC-156/320/650 A/B /
ITC-320/650 A)
Spare part no. for multi-hole inserts - metric (mm)
Instruments
Insert code
M01
M02
M03
M04
M06
M07
M08
1
ATC-125 A/B ATC-155/156 A/B
ATC-157 A/B /
ITC-155 A
126272 122751 123294 122750 124897 124889
126273 122753 123295 122752 N/A N/A
126274 122755 123296 122754 N/A N/A
126275 122757 N/A 122756 N/A N/A
N/A N/A 125377 N/A N/A N/A
N/A N/A 125378 N/A N/A N/A
N/A N/A 125379 N/A N/A N/A
ATC-320/650 A/B
ITC-320/650 A
ATC-140 A/B ATC-250 A/B
Note: All multi-hole inserts (metric and inches) for ATC-125/140/156/157 and ITC-155 are supplied with a matching insulation plug. Note: Remember to use matching insulation plugs. Note 1: Use the insert code, when ordered as the standard insert together with a new calibrator.
6 www.jofra.com
1/4
3
6
Insertion tubes for temperature dry-blocks
MULTI-HOLE INSERTS FOR ATC AND ITC SERIES - IMPERIAL (INCH)
Accessory Sheet AS-CP-2205-US
1/2
5/16
3/16
1/4
3/16
1/4
7/16
Multi-hole M02
(ATC-140/250 A/B)
1/8
1/8
4
3/16
Multi-hole M04
(ATC-157 A/B / ITC-155 A)
4
1/4
1/4
1/4
4
1/4
1/4
1/8
4
3/8
1/4
1/4
1/4
1/4
Multi-hole M05
1/4
(ATC-125 A/B)
4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
Multi-hole M05
(ATC-156/320/650 A/B /
ITC-320/650 A)
1/8
1/8
1/4
1/4
3/16
4
1/8
1/4
3/8
1/4
3/16
Multi-hole M06
(ATC-125 A/B)
4
1/8
1/4
3/8
1/4
3/16
Multi-hole M06
(ATC-156/320/650 A/B /
ITC-320/650 A)
Multi-hole M05
(ATC-157 A/B / ITC-155 A)
Spare part no. for multi-hole inserts - imperial (inch)
Insert code
M02
M04
M05
M06
M09
1
ATC-125 A/B ATC-155/156 A/B
N/A N/A N/A N/A 124898 124890
N/A N/A 123297 N/A N/A N/A
126276 122759 123298 122758 N/A N/A
126277 122761 N/A 122760 N/A N/A
N/A N/A 125380 N/A N/A N/A
Multi-hole M09
(ATC-157 A/B / ITC-155 A)
ATC-157 A/B /
ITC-155 A
Instruments
ATC-320/650 A/B
ITC-320/650 A
ATC-140 A/B ATC-250 A/B
Note: All multi-hole inserts (metric and inches) for ATC-125/140/156/157 and ITC-155 are supplied with a matching insulation plug. Note: Remember to use matching insulation plugs. Note 1: Use the insert code, when ordered as the standard insert together with a new calibrator.
www.jofra.com 7
ORDERING CUSTOM-MADE SPECIAL INSERTS
Schedule for Insert – Order Form
AMETEK D enma rk A/S
• G ydev ang 32- 34 • 34 50 A ller ød • De nmar k • CVR nr .: D K 14 747 079 105171 11
Phon e: + 45 4 816 800 0 • Fax : +4 5 4 816 808 0 • E-ma il: ame tek@ ame tek. dk • ww w.jo fra. com 11-0 4-20 08
The Order Form must be filled in by the customer / distributor
Customer information AMETEK Denmark use only
Company
CSD Department
Purchase Department
Sales order: Purchase no:
Initial: Date: Initial: Date:
Order information
Enquiry only Order Customer drawing 110296 Calibrator model : ______________________________________
Single hole inserts
Incl. one reference hole ø4.2
Model
CTC­320 A
CTC­320 B
CTC­650 A
CTC­650 B
CTC­140 A
D55SE-9TOWER 2CE-
140SE 1”
SD40 ATC-155/
156 A/B
ITC/ ATC-320/ 650 A/B
CTC­1200 A
ITC-155 A/ATC­157 A/B
ATC-156 A/B Clamp insert
ATC-125 A/B
ATC-140
A/B
ATC-250 A/B
Part no.
60F355 60F379 60F419 60F447 60F505 60F508 60F519 60F534 60F701 122885 122886 124408 123400 123868 126160 124900 126162
Pcs.
Requested holes in insert (NOT INCLUDING THE ADDITIONAL DIMENSION). Sensor size – ø Diameter (inch/mm)
Hole no.
Hole no. 1 Hole no. 2 Hole no. 3 Hole no. 4 Hole no. 5 Hole no. 6 Hole no. 7 Hole no. 8 Hole no. 9 Hole no. 10 Hole no. 11 Hole no. 12 Hole no. 13 Hole no. 14
No. of holes
CONDITION: We reserve the right to alter any mechanical construction
Notes
Multi- hole inserts
Model
CTC-320 A CTC-320 B CTC-650 A CTC-650 B CTC-1200 ACTC-140 A TOWER-2 CE-140SE 1”ATC-125
A/B
ATC-155/ 156 A/B
ITC/ATC­320/650 A/B
ITC-155/ ATC-157 A/B
ATC-140 A/B
ATC-250 A/B
Part no.
60F357 60F380 60F421 60F449 125475 60F506 60F518 60F535 126343 123398 123399 123401 126156 126161
Pcs.
Custom-made special inserts are made on request.
When ordering custom made special inserts a few details have to be noticed:
• Specify the instrument for which the inserts are ordered
• Specify the sensor size for each hole
Please use our order form for custom-made insert, which are available at www.jofra.com
APPLICATION KIT FOR CALIBRATION OF SANITARY SENSORS
At picture 1 you see a custom made insert and our STS-102 A cable reference sensor placed in a JOFRA ATC-156 B dry-block calibrator. At picture 2, the sanitary sensor has been fitted into the insert and is ready for calibration. Note that the design makes room for the reference sensor cable.
To learn more about calibration of sanitary temperature sensors please see accessory sheet AS-CP-2201 available at www.jofra.com
is one of the world’s leading manufacturers and
AMETEK Calibration Instruments
developers of calibration instruments for
temperature, pressure and process signals
as well as for temperature sensors both from
a commercial and a technological point of view.
JOFRA Temperature Instruments
Portable precision thermometers. Dry-block and
liquid bath calibrators: 4 series, with more than
25 models and temperature ranges from
-90° to 1205°C / -130° to 2200°F. All featuring speed, portability, accuracy and advanced documenting
functions with JOFR ACAL calibration software.
JOFRA Pressure Instruments
Convenient electronic systems ranging from
-1 to 1000 bar (25 inHg to 14,500 psi) -
multiple choices of pressure ranges, pumps and
accuracies, fully temperature- compensated
for problem-free and accurate field use.
JOFRA Signal Instruments
Process signal measurement and simulation for
easy control loop calibration and measurement
tasks - from handheld field instruments to
laboratory reference level bench top instruments.
JOFRA / JF Marine Instruments
A complete range of calibration equipment
for temperature, pressure and signal,
approved for marine use.
FP Temperature Sensors
A complete range of temperature sensor s
for industrial and marine use.
M&G Pressure Testers
Pneumatic floating-ball or hydraulic piston dead
weight testers with accuracies to 0.015% of reading.
M&G Pumps
Pressure generators from small pneumatic
“bicycle” style pumps to hydraulic pumps
generating up to 1,000 bar (15,000 psi).
Picture 1 Picture 2 Application kit
Headquarters:
AMETEK Denmark A/S Gydevang 32-34 • 3450 Allerød • Denmark Tel: +45 4816 8000 • ametek@ametek.dk
Sales & Service: Europe, Asia, Africa, Middle East and South America
Information in this document is subject to change without notice. ©2007, by AMETEK, Inc., www.ametek.com. All rights reserved.
Pub code AS -CP-2205-US Issue 0 805
8 www.jofra.com
.. .b ec au se c al ib ra tion is a ma tter of confidence
www.ametekcalibration.com
www.jofra.com
Sales & Service Offices:
AMETEK Mansfield & Green (North America)
Tel: +1 800 527 9999 • cal.info@ametek.com
AMETEK Singapore Pte. Ltd. (Singapore) Tel: +65 6 484 2388 • aspl@ametek.com.sg
AMETEK Inc. Beijing Rep. Office (China)
Tel: +86 10 8526 2111 • jofra@ametek.com.cn
AMETEK GmbH (Germany)
Tel: +49 2159 91360 • info@ametek.de
AMETEK Lloyd Instruments (UK)
Tel: +44 (0) 1489 486 404 • jofra@ametek.co.uk
Loading...