AMETEK LPDC-65V User Manual
Technical Note
ReFlex Power™ Mating Connectors for LPDC-65V Module
Document No. W380270-02 Rev E •1/23/2009
PURPOSE
Provide mating connector information for the ReFlex Po wer™ Low Powe r DC, 65V (LPDC-65V) module.
Figure 1. LPDC-65 Front Panel View
MATING CONNECTOR KIT
LPDC-65V Mating Connector Kit - AMETEK Part No. 5380270-02, mates with RFP-D1065-5A1-XXXX, and includes the
following for both Interface and DC output connectors:
Bill of Material
Item
1 856-214-07
2 856-745-53
3 856-247-39
4 856-214-09
5 856-247-10
AMETEK
Part No.
Description Qty
Conn, 13P, DSUB,
8/20AWG, Male
Contact, F-Volt,
3600VRMS, 500C, Male
Conn, Backshell, 37P, Strt,
2 PC
Conn, 9P, DSUB, 2024AWG, Crimp, Male
Conn, Backshell, 9P,
DSUB, 2 PC
Manufacturer
Part No.
1 CBD13W6M2000Z Positronic Industries
6 MS4820D-50 Positronic Industries
1 D37000Z00 Positronic Industries
1 SD9M1000Z Positronic Industries
1 D9000Z00 Positronic Industries
Manufacturer Suggested Source(s)
Positronic Ind.
http://www.connectpositronic.com/default.cfm
Positronic Ind.
http://www.connectpositronic.com/default.cfm
Positronic Ind.
http://www.connectpositronic.com/default.cfm
Positronic Ind.
http://www.connectpositronic.com/default.cfm
Positronic Ind.
http://www.connectpositronic.com/default.cfm
RECOMMENDED TOOLS (NOT INCLUDED WITH MATING CONNECTOR KIT)
Hand crimp: Positronic Industries P/N 95 07-0-0-0
Pneumatic crimp: Positronic Industries P/N 9550-1-0
Insertion/extraction: Positronic Industries P /N M81969/1-02
Pins A1 through A6 insertion/extraction: Positronic Industries P/N 4311-0-0 -0
9250 Brown Deer Road, Sa n Diego CA 92121 • Tel: 858-4 50-008 5 • Fax: 858-458- 0267 • e mail: sal es@progra mmablep ower.com
©2008 AMETEK Programmable Pow er, Inc. • All rights reserv ed. • AME TEK is a tr ademark o f AMETEK, Inc .
• Web: www.programmablepower.com
1 of 4
Technical Note
ReFlex Power™ Mating Connectors for LPDC-65V Module
Document No. W380270-02 Rev E •1/23/2009
INTERFACE CONNECTOR
External isolated digital and analog cont rol interface.
Connector: Positronic Industries P/N SD9M1000Z, AMETEK P/N 856-214-09
Crimp contacts: Positronic Industries P/N MC75 20D (initially suppli ed with conne ctor)
Backshell: Positronic Industries P/N D9000Z00, AMETEK P/N 856-247-10
Wire size: Maximum gauge 20 AWG (recommended)
Maximum length 10 meters (can be extended subject to enviro nment, cable type, and interfa ce circuits).
INTERFACE PINOUT
Figure 2. Interface Connector, Front Panel View, and Interface Connector Wiring Diagram
Pin Name Function Signal Level
1 ENA1 Input: module output enable TTL logic level 20
6 ENA-RTN1 Input: return for ENA signal; connected to Pin-7/8 Signal common 20
2 TRIG-OUT Output: trigger output signal TTL logic level 20
7 TRIG-OUT-RTN Output: return for TRIG-OUT; connected to Pin-6/8 Signal common 20
3 TRIG-IN Input: trigger input signal TTL logic level 20
8 TRIG-IN-RTN Input: return for TRIG-IN; connected to Pin-6/7 Signal common 20
4 Reserved
9 Reserved
5 CHAS-GND Shield ground Chassis ground 20
1
Enable signal is internally pulled up to +5 V with a 10 K resistor. To enable the module, the signal is pulled low (<= 0.5 V) with respect
to the ENA RTN signal; this may also be accomplished by shorting Pin 1 to Pin 6.
Wire Gauge,
AWG
9250 Brown Deer Road, Sa n Diego CA 92121 • Tel: 858-4 50-008 5 • Fax: 858-458- 0267 • e mail: sal es@progra mmablep ower.com
©2008 AMETEK Programmable Pow er, Inc. • All rights reserv ed. • AME TEK is a tr ademark o f AMETEK, Inc .
• Web: www.programmablepower.com
2 of 4
Loading...