Page 1
Technical Note
ReFlex Power™ Mating Connectors for HPDC-450V Module
Document No. W380271-02 Rev E • 1/23/2009
PURPOSE
Provide mating connector information for the ReFlex Po wer™ High P ower DC, 450V (HP DC-450V) modul e.
Figure 1. HPDC-450 Front Panel View
MATING CONNECTOR KIT
HPDC-450V Mating Connector Kit - AMETEK Part No. 5380271-02, mates with RFP-D2450-2A3-XXXX, and includes the
following for both Interface and DC output connectors:
Bill of Material
AMETEK
Item
Part No.
1 856-214-04 Conn, 21P, DSUB, 8/20AWG, Male 1 CBC21WA4M1000Z Positronic Industries
2 856-745-53
3 856-247-39 Conn, Backshell, 37P, Strt, 2 PC 1 D37000Z00 Positronic Industries
4 856-214-09
5 856-247-10 Conn, Backshell, 9P, DSUB, 2 PC 1 D9000Z00 Positronic Industries
Contact, F-Volt, 3600VRMS, 500C,
Male
Conn, 9P, DSUB, 20-24AWG,
Crimp, Male
Description Qty
Manufacturer
Part No.
4 MS4820D-50 Positronic Industries
1 SD9M1000Z Positronic Industries
Manufacturer Suggested Source(s)
Positronic Ind.
http://www.connectpositronic.com/default.cfm
Positronic Ind.
http://www.connectpositronic.com/default.cfm
Positronic Ind.
http://www.connectpositronic.com/default.cfm
Positronic Ind.
http://www.connectpositronic.com/default.cfm
Positronic Ind.
http://www.connectpositronic.com/default.cfm
RECOMMENDED TOOLS (NOT INCLUDED WITH MATING CONNECTOR KIT)
Hand crimp: Positronic Industries P/N 95 07-0-0-0
Pneumatic crimp: Positronic Industries P/N 9550-0-2
Insertion/extraction: Positronic Industries P /N M81969/1-02
9250 Brown Deer Road, Sa n Diego CA 92121 • Tel: 858-4 50-008 5 • Fax: 858-458- 0267 • e mail: sal es@progra mmablep ower.com • Web: www.programm ablepow er.com
©2008 AMETEK Programmable Pow er, Inc. • All rights reserv ed. • AME TEK is a tr ademark o f AMETEK, Inc .
1 of 3
Page 2
Technical Note
ReFlex Power™ Mating Connectors for HPDC-450V Module
Document No. W380271-02 Rev E • 1/23/2009
Pins A1 through A6 insertion/extraction: Positronic Industries P/N 4311-0-0 -0
INTERFACE CONNECTOR
External isolated digital and analog cont rol connect or.
Connector: Positronic Industries P/N SD9M1000Z, AMETEK P/N 856-214-09
Crimp contacts: Positronic Industries P/N MC75 20D (initially suppli ed with conne ctor)
Backshell: Positronic Industries P/N D9000Z00, AMETEK P/N 856-247-10
Wire size: Maximum gauge 20 AWG (recommended)
Maximum length10 meters (can be extended subject to t he environment, cable ty pe, and interface ci rcuits).
INTERFACE PINOUT
Figure 2. Interface Connector, Front Panel View, and Interface Connector Wiring Diagram
Pin Name Function Signal Level
1 ENA1 Input: module output enable TTL logic level
6 ENA-RTN1 Input: return for ENA signal; connected to Pin-7/8 Signal common
2 TRIG-OUT Output: trigger output signal TTL logic level
7 TRIG-OUT-RTN Output: return for TRIG-OUT; connected to Pin-6/8 Signal common
3 TRIG-IN Input: trigger input signal TTL logic level
8 TRIG-IN-RTN Input: return for TRIG-IN; connected to Pin-6/7 Signal common
4 Reserved
9 Reserved
5 CHAS-GND Shield ground Chassis ground
1
Enable signal is internally pulled up to +5 V with a 10 K resistor. To enable the module, the signal is pulled low
(<= 0.5 V) with respect to the ENA RTN signal; this may also be accomplished by shorting Pin 1 to Pin 6.
OPTIONAL INTERFACE CONNECTOR ACCESSORIES
• AMETEK P/N 5380508-01, 9-pin Loop-back Connector Assembly. Includes a jumper wire between Pins 1 and 6 to enable
the module outputs.
• AMETEK P/N 5380443-01, Power Module, 9ft. Unterminated Interface Cable Assembly. Use when interfacing to an
external system.
• AMETEK P/N 5380443-03, Power Module, Right Angle, 9ft. Unterminated Interface Cable Assembly. Use when interfacing
to an external system.
9250 Brown Deer Road, Sa n Diego CA 92121 • Tel: 858-4 50-008 5 • Fax: 858-458- 0267 • e mail: sal es@progra mmablep ower.com • Web: www.programm ablepow er.com
©2008 AMETEK Programmable Pow er, Inc. • All rights reserv ed. • AME TEK is a tr ademark o f AMETEK, Inc .
2 of 3
Page 3
Technical Note
ReFlex Power™ Mating Connectors for HPDC-450V Module
Document No. W380271-02 Rev E • 1/23/2009
DC OUTPUT CONNECTOR
Connector: Positronic Industries P/N CBC21WA4M1000Z, AMETEK P/N 856-214-04
Crimp contacts: Positronic Industries P/N MC6020D
Pins A1-A4: Positronic Industries P/N MS4820D-50, AMETEK P/N 856-745-53
Backshell: Positronic Industries P/N D37000Z00, AMETEK P/N 856-247-39
Wire size: Maximum gauge 20 AWG (re commended)
Refer to table for recommended wire ga uge/length.
DC OUTPUT PINOUT
Figure 3. DC Output Connector, Front Panel View
Pin Name Function Signal Level
A1 OUT
A2 OUT-RTN
A3 SNS
A4 SNS-RTN
9 CHAS-GND Shield ground Chassis ground 20 45
1-8,
10-17
Output: module output source;
connected to A3
Output: return for output source, OUT;
connected to A4
Input: remote sense connection for
OUT
Input: remote sense connection for
OUT-RTN
- Reserved - - -
±450V; ±450V, maximum
to chassis
±450V; ±450V, maximum
to chassis
±450V; ±450V, maximum
to chassis
±450V; ±450V, maximum
to chassis
Maximum Wire
Gauge, AWG
20
20
20 45
20 45
Maximum Wire
Length, ft
45, for 1.5V line drop
at 15A
45, for 1.5V line drop
at 15A
DC OUTPUT CONNECTOR ACCESSORIES
• AMETEK P/N 5380447-01, HPDC 450V Module, 9ft. Unterminated DC Output Cable Assembly.
• AMETEK P/N 5380447-03, HPDC 450V Module, right angle, 9ft. Unterminated DC Output Cable Assembly.
9250 Brown Deer Road, Sa n Diego CA 92121 • Tel: 858-4 50-008 5 • Fax: 858-458- 0267 • e mail: sal es@progra mmablep ower.com • Web: www.programm ablepow er.com
©2008 AMETEK Programmable Pow er, Inc. • All rights reserv ed. • AME TEK is a tr ademark o f AMETEK, Inc .
3 of 3
Loading...