AMETEK HPAL User Manual

Technical Note

ReFlex Power™ Mating Connectors for HPAL/LPAL Module

Document No. W380273-01 Rev D • 1/23/2009

PURPOSE

Provide mating connector information for the ReFlex Po wer™ High Power and Low Power Active Loa d (HP/LPAL) mod ule.

Figure 1. HP/LPAL Front Panel View

MATING CONNECTOR KIT

Load (HPAL/LPAL) Mating Connector Kit - AMETEK Part No. 5380273-01, mates with RFP-L3500-375-XXXX and RFP-L3500­750-XXXX, and includes the following for both the Interface and DC input connectors:

Bill of Material

Item

AMETEK

Part No.

1 855-363-08
2 856-214-09
3 856-247-10

Description Qty

Conn, 4P, 8/16AWG,
Plug, SR, Skt
Conn, 9P, DSUB, 20­24AWG, Crimp, Male
Conn, Backshell, 9P,
DSUB, 2 PC

Manufacturer

Part No.

1 MS3106F-20-24S
1 SD9M1000Z Positronic Industries
1 D9000Z00 Positronic Industries

Manufacturer Suggested Source(s)

Amphenol,
ITT Cannon

PEI-Genesis: http://www.pei-genesis.com/
Arrow Electronics: http://www.arrownac.com/
Positronic Ind.

http://www.connectpositronic.com/default.cfm

Positronic Ind.

http://www.connectpositronic.com/default.cfm

RECOMMENDED TOOLS (NOT INCLUDED WITH MATING CONNECTOR KIT)

Hand crimp: Positronic Industries P/N 95 07-0-0-0
Pneumatic crimp: Positronic Industries P/N 9550-1-0
Insertion/extraction: Positronic Industries P /N M81969/1-02

9250 Brown Deer Road, Sa n Diego CA 92121 • Tel: [phone] • Fax: [phone] • e mail: sal es@progra mmablep ower.com • Web: www.programm ablepow er.com

©2008 AMETEK Programmable Pow er, Inc. • All rights reserv ed. • AME TEK is a tr ademark o f AMETEK, Inc .

1 of 3

Technical Note

ReFlex Power™ Mating Connectors for HPAL/LPAL Module

Document No. W380273-01 Rev D • 1/23/2009

INTERFACE CONNECTOR

External isolated digital and analog cont rol interface
Connector: Positronic Industries P/N SD9M1000Z, AMETEK P/N 856-214-09

Crimp contacts: Positronic Industries P/N MC75 20D (initially suppli ed with conne ctor)
Backshell: Positronic Industries P/N D9000Z00, AMETEK P/N 856-247-10
Wire size: Maximum gauge 20 AWG (22 AWG recommended)

Maximum length 10 meters.

INTERFACE PINOUT

Figure 2. Interface Connector, Front Panel View, and Interface Connector Wiring Diagram

Pin Name Function Signal Level

1

ENA-RTN

6

Reserved

2

Reserved

7

Reserved

3

Reserved

8

MOD-IN-H Input: external modulation signal; differential input with MOD_IN_L 5V/10V analog signal

4

MOD-IN-L Input: return for external modulation signal, MOD_IN_H 5V/10V analog signal

9

CHAS-GND Shield ground Chassis ground

5

1

Enable signal is internally pulled up to +5 V with a 10 K resistor. To enable the module, the signal is pulled low (<= 0.5 V) with respect to

the ENA RTN signal; this may also be accomplished by shorting Pin 1 to Pin 6.

1

Input: return for ENA signal; connected to Pin-7/8 Signal common

1

Input: module output enable TTL logic level

ENA

OPTIONAL INTERFACE CONNECTOR ACCESSORIES

• AMETEK P/N 5380508-01, 9-pin Loop-back Connector Assembly. Includes a jumper wire between Pins 1 and 6 to enable

the module outputs.

• AMETEK P/N 5380443-01, Power Module, 9ft. Unterminated Interface Cable Assembly. Use when interfacing to an

external system.

• AMETEK P/N 5380443-03, Power Module, Right Angle, 9ft. Unterminated Interface Cable Assembly. Use when interfacing

to an external system.

9250 Brown Deer Road, Sa n Diego CA 92121 • Tel: [phone] • Fax: [phone] • e mail: sal es@progra mmablep ower.com • Web: www.programm ablepow er.com

©2008 AMETEK Programmable Pow er, Inc. • All rights reserv ed. • AME TEK is a tr ademark o f AMETEK, Inc .

2 of 3