American Standard T106.500, T106.501, T106.502, T106.507, T106.508 Installation Manual
INSTALLATION
INSTRUCTIONS
T106.500
PATIENCE
TUB AND SHOWER
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please
read these instructions carefully before you begin.
RECOMMENDED TOOLS
Phillips Screwdriver
Plumbers’ Putty
or Caulking
ROUGHING-IN DIMENSIONS
• To assure proper positioning in relation to wall.
Note roughing-in dimensions.
FINISHED WALL
9-1/2"
(223 mm)
3-3/4"
(97 mm)
(160 mm)
7-3/8"
(187 mm)
7"
Teon Tape
2" TO 3"
(51 TO 76 mm)
1/2" NPT
Flat Blade Screwdriver
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65'' AND 78"
(1651 AND 1981 mm)
SHR. 1/2" NOM.
COPPER SWEAT
SWEAT
INLETS
TUB 1/2" NOM.
COPPER SWEAT
T106.501
T106.502
T106.507
T106.508
Certied to comply with ANSI A112.18.1M
Adjustable Wrench Channel Locks
INLETS
INLETS
4-1/16"
(103 mm)
1/2" NOM.
COPPER
SWEAT
2"
(103 mm)
SWEAT
INLETS (STOPS)
4-1/16"
5-7/8"
(149 mm)
74" (1879 mm)
FOR HEAD
CLEARANCE
4-1/8"
(105 mm)
18" (457 mm)
OPTIONAL
2-3/4"
(83 mm)
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
7-5/8"
(207 mm)
1-1/2"
6-5/8"
(179 mm)
TOP OF TUB RIM
BOTTOM OF TUB
(198 mm)
1/2" COPPER
FOR SLIP-ON
SPOUT
SHR. 1/2" NOM.
COPPER SWEAT
TUB 1/2" NOM.
COPPER SWEAT
8"
OUTLETS
INLETS 1/2" NPT
3-3/8"
(86 mm)
3-3/8"
OUTLETS
1/2" NPT
4"
THREADED INLETS
(86 mm)
1/2" NPT
THREADED INLETS (STOPS)
5-7/8"
(149 mm)
5-7/8"
(149 mm)
- 1 -
4-1/16" (103 mm)
INLETS
1/2" NOM.
COPPER
SWEAT
INLETS
1/2" NPT
M965819 (6/17)
1
INSTALL VALVE TRIM
• Figure 1. Remove plaster guard from valve. Push
CAP (1) over VALVE CARTRIDGE (2) until seated
against stop.
• Figure 2. Push ESCUTCHEON (3) onto CAP (1) and
attach to valve body with LONG SCREWS (4) (cut
screws if needed). Mount DECORATIVE PLATE (5) to
ESCUTCHEON (3) by aligning three PINS (6) on back
side of DECORATIVE PLATE (5).
PLASTER
GUARD
Figure 1.
1
2
1
2
INSTALL TUB SPOUT, SHOWER HEAD,
SHOWER ARM WITH FLANGE
• Remove pipe cap and plug from shower and tub
rough piping.
• Slip DECORATIVE PLATE (5), then slip TUB SPOUT (1)
onto tub nipple and tighten with 4mm Hex Wrench.
CAUTION: Protect finish on TUB SPOUT when
installing.
• Install SHOWER ESCUTCHEON (2) onto SHOWER
ARM (3). Apply sealant or Teon tape to threads on
both ends of SHOWER ARM (3) and thread longer
leg of SHOWER ARM (3) into shower elbow.
• Thread SHOWER HEAD (4) onto SHOWER ARM (3).
CAUTION: Protect finish on SHOWER HEAD and
ARM when installing.
CAUTION
Figure 2.
Protect finish on SHOWER HEAD
and TUB SPOUT when installing.
4
3
6
H
C
4
5
2
SHR.
ELBOW
PIPE
PLUG
3
1
- 2 -
PIPE
CAP
TUB FILLER
NIPPLE
5
1-1/2" REF.
2.5 MM HEX
WRENCH
M965819 (6/17)
Loading...