American Standard T075.508, T075.508XH, T075.507, T075.507XH, T075.500 Installation Manual
INSTALLATION
INSTRUCTIONS
T075.500
COLONY® PRO
TUB AND SHOWER
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please
read these instructions carefully before you begin.
RECOMMENDED TOOLS
Phillips Screwdriver
Plumbers’ Putty
or Caulking
ROUGHING-IN DIMENSIONS
• To assure proper positioning in relation to wall.
Note roughing-in dimensions.
FINISHED WALL
8-9/16"
(217 mm)
4-1/16"
(99 mm)
74" (1879 mm)
FOR HEAD
CLEARANCE
18" (457 mm)
OPTIONAL
(72 mm)
"SEE ILLUSTRATIONS "
4-3/16"
(106 mm)
2-7/8"
TOP OF TUB RIM
(155 mm)
7-1/2"
(190 mm)
5-11/16"
(144 mm)
1-1/2"
4-7/8"
(124 mm)
BOTTOM OF TUB
6-1/8"
Teon Tape
2" TO 3"
(51 TO 76 mm)
1/2" NPT
1/2" COPPER
FOR SLIP-ON
SPOUT
Flat Blade Screwdriver
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65'' AND 78"
(1651 AND 1981 mm)
7-1/2"
(190 mm)
3-3/8"
(86 mm)
OUTLETS
1/2" NPT
4"
SHR. 1/2" NOM.
COPPER SWEAT
SWEAT
INLETS
TUB 1/2" NOM.
COPPER SWEAT
INLETS 1/2" NPT
THREADED INLETS
T075.507
T075.508
T075.507xH
T075.508xH
Adjustable Wrench Channel Locks
INLETS
INLETS
4-1/16"
(103 mm)
1/2" NOM.
COPPER
SWEAT
SWEAT
INLETS (STOPS)
SHR. 1/2" NOM.
COPPER SWEAT
TUB 1/2" NOM.
COPPER SWEAT
3-3/8"
(86 mm)
OFF
Certied to comply with ANSI A112.18.1M
2"
4-1/16"
(103 mm)
5-7/8"
(149 mm)
OUTLETS
1/2" NPT
THREADED INLETS (STOPS)
5-7/8"
(149 mm)
5-7/8"
(149 mm)
4-1/16" (103 mm)
INLETS
1/2" NOM.
COPPER
SWEAT
INLETS
1/2" NPT
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2016
- 1 -
M965762 (8/16)
1
INSTALL VALVE TRIM
• Figure 1. Remove plaster guard from valve. Push
CAP (1) over VALVE CARTRIDGE (2) until seated
against stop.
• Figure 2. Push ESCUTCHEON (3) onto CAP (1) and
attach to valve body with LONG SCREWS (4).
PLASTER
GUARD
Figure 1.
1
2
1
3
2
INSTALL TUB SPOUT, SHOWER HEAD,
SHOWER ARM WITH FLANGE
• Remove pipe cap and plug from shower and tub
rough piping.
• Slip TUB SPOUT (1) onto tub nipple and tighten with
2.5 mm Hex Wrench.
CAUTION: Protect finish on TUB SPOUT when
installing.
• Install SHOWER ESCUTCHEON (2) onto SHOWER
ARM (3). Apply sealant or Teon tape to threads on
both ends of SHOWER ARM (3) and thread longer
leg of SHOWER ARM (3) into shower elbow.
• Thread SHOWER HEAD (4) onto SHOWER ARM (3).
CAUTION: Protect finish on SHOWER HEAD and
ARM when installing.
• Slip ADAPTER (5) onto CARTRIDGE (6) and thread
SCREW (7) on.
CAUTION
Figure 2.
Protect finish on SHOWER HEAD
and TUB SPOUT when installing.
SHR.
ELBOW
PIPE
PLUG
OFF
OFF
4
2
3
4
6
5
7
TUB FILLER
NIPPLE
1-1/2" REF.
- 2 -
2.5 MM HEX
WRENCH
1
M965762 (8/16)
Loading...