American Standard T038.990 User Manual
Installation
Instructions
DECK MOUNT
TUB FILLERS
TROPIC DIVERTER & PERSONAL
SHOWER TRIM KITS
with EverClean™ Finish
Congratulations on purchasing your American Standard
faucet with EverClean finish found only on American
Standard faucets.
EverClean Finish
• One wipe effortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
INSTALL HANDLE ADAPTER
1
Remove DIVERTER GUARD (1) from valve.
T038.990
3
2
Certified to comply with ANSI A112.18.1
U.S. Patent No. D403,750
M968897
5
Place the ESCUTCHEON SEAL (7) into groove of DECK ADAPTER (2).
Align the HANDLE STEM (3) with the SLEEVE (4) as necessary.
Thread the HANDLE ADAPTER (5) into the VALVE BODY (6) until
the DECK ADAPTER (2) contacts tight against the finished
mounting surface.
INSTALL HANDLES
2
Push ADAPTER (1) on VALVE STEM (2), so that
the hole of the ADAPTER (1) without a spline is
facing up. Fig. A. Tighten STEM SCREW (3) to
secure ADAPTER (1).
Find correct position of LEVER HANDLE ASSEMBLY (4)
by adjusting male teeth on ADAPTER (1) to female teeth
in HANDLE (4).
Thread LEVER HANDLE ASSEMBLY (4) onto DECK
ADAPTER (5) until snug against mounting surface.
4
TOP
GROOVE
7
4
2
1
6
THREAD ON
TO DECK
ADAPTER
1
3
SPLINE END DOWN
Fig. A.
5
INSTALL HAND SHOWER
3
Unscrew the HOLDER (1) from the SHOWER ESCUTCHEON (2). Slip the
SHOWER HOSE (3) through the SHOWER ESCUTCHEON (2) and the
HOLDER (1).
Pull out the SLEEVE GUARD (6) and HOSE (7). Unthread the SLEEVE GUARD
(6) from the HOSE END (8) connection. Be careful not to allow the HOSE
(7) to fall back through the SLEEVE (9).
Insert SEAL WASHER (10) into the SHOWER HOSE CONNECTOR (11).
Thread the SHOWER HOSE CONNECTOR (11) onto the HOSE END (8) and
tighten securely.
Thread the SHOWER ESCUTCHEON (2) into the SLEEVE (9) until the
SHOWER ESCUTCHEON (2) contacts the finished deck.
Loosen the SET SCREW (12) in the SHOWER ESCUTCHEON (2) and rotate
the ESCUTCHEON (2) so that SET SCREW (12) faces the center of the tub.
Retighten the SET SCREW (12).
Thread the HOLDER (1) into the SHOWER ESCUTCHEON (2).
Insert a SEAL WASHER (4) into the SHOWER HOSE CONNECTOR (5)
and hand tighten HAND SHOWER (13) into
SHOWER HOSE CONNECTOR (5).
Place the HAND SHOWER (13)
into the HOLDER (1).
6
11
10
8
7
13
5
1
2
3
4
13
1
12
2
TEST INSTALLED DIVERTER
4
Turn DIVERTER VALVE (1) fully clockwise (Tub fill position).
Turn on control valves and check all connections for leaks. With
DIVERTER VALVE (1) in clockwise position, flow should only come
from tub spout.
Lift HANDSHOWER (2) from holder, direct spray into tub, turn
DIVERTER VALVE (1) fully counter-clockwise to check
HANDSHOWER (2) and HOSES (3) for leaks. With DIVERTER
VALVE (1) in counter-clockwise position, flow should only
come from HANDSHOWER (2).
Turn control valves "off."
EverClean™ Finish Care Instructions
5
9
2
1
3
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with
clean water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
M968897
Loading...