American Standard T018.50X Installation Manual
EDGEMERE
™
TUB AND SHOWER
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please
read these instructions carefully before you begin.
RECOMMENDED TOOLS
Phillips Screwdriver
INSTALLATION
INSTRUCTIONS
T018.50X
H
C
OFF
Certied to comply with ANSI A112.18.1M
Plumbers’ Putty
or Caulking
Teon Tape
ROUGHING-IN DIMENSIONS
• To assure proper positioning in relation to wall.
Note roughing-in dimensions.
1-5/8" to 3-1/4"
1/2" (13 mm) I.P.S.
FINISHED FLOOR USUALLY
BETWEEN 65" AND 78"
(1651 AND 1981MM)
FINISHED WALL
7-11/16" (195 mm)
18" (457 mm)
OPTIONAL
4-1/8" (108 mm)
1/2" NPT
*5-1/8" (130 mm) Ref.
TOP OF TUB RIM
4" (102 mm)
Flat Blade Screwdriver
SHR. 1/2" NOM.
COPPER SWEAT
SWEAT
INLETS
TUB 1/2" NOM.
COPPER SWEAT
INLETS 1/2" NPT
3-3/8"
(86 mm)
OUTLETS
1/2" NPT
Adjustable Wrench Channel Locks
INLETS
INLETS
4-1/16"
(103 mm)
1/2" NOM.
COPPER
SWEAT
2"
(103 mm)
SWEAT
INLETS (STOPS)
SHR. 1/2" NOM.
COPPER SWEAT
TUB 1/2" NOM.
COPPER SWEAT
3-3/8"
(86 mm)
4-1/16"
OUTLETS
1/2" NPT
5-7/8"
(149 mm)
5-7/8"
(149 mm)
5-7/8"
(149 mm)
4-1/16" (103 mm)
INLETS
1/2" NOM.
COPPER
SWEAT
INLETS
1/2" NPT
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
THREADED INLETS
- 1 -
THREADED INLETS (STOPS)
M965807 (3/17)
1
INSTALL VALVE TRIM
• Figure 1. Remove plaster guard from valve. Push
CAP (1) over VALVE CARTRIDGE (2) until seated
against stop.
• Figure 2. Push ESCUTCHEON (3) onto CAP (1) and
attach to valve body with LONG SCREWS (4). Mount
DECORATIVE PLATE (5) to ESCUTCHEON (3) by
aligning three PINS (6) on back side of DECORATIVE
PLATE (5).
PLASTER
GUARD
Figure 1.
1
2
1
3
OFF
6
H
C
4
2
INSTALL TUB SPOUT, SHOWER HEAD,
SHOWER ARM WITH FLANGE
• Remove pipe cap and plug from shower and tub
rough piping.
• Slip DECORATIVE PLATE (5), then slip TUB SPOUT (1)
onto tub nipple and tighten with 2.5 mm Hex Wrench.
CAUTION: Protect finish on TUB SPOUT when
installing.
• Install SHOWER ESCUTCHEON (2) onto SHOWER
ARM (3). Apply sealant or Teon tape to threads on
both ends of SHOWER ARM (3) and thread longer
leg of SHOWER ARM (3) into shower elbow.
• Thread SHOWER HEAD (4) onto SHOWER ARM (3).
CAUTION: Protect finish on SHOWER HEAD and
ARM when installing.
CAUTION
TUB FILLER
Figure 2.
Protect finish on SHOWER HEAD
and TUB SPOUT when installing.
SHR.
ELBOW
PIPE
PLUG
C
OFF
NIPPLE
1-1/2" REF.
5
2
3
4
H
PIPE
CAP
5
- 2 -
2.5 MM HEX
WRENCH
1
M965807 (3/17)
Loading...