Page 1
Recommended Tools
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
Plumbers' Putty or Caulking
Phillips Screwdriver
Teflon Tape
FINISHED WALL
4"
TOP OF TUB RIM
BOTTOM OF TUB
74" FOR HEAD
CLEARANCE
3-1/8" REF.
1-5/8" TO 3"
18" OPTIONAL
4-5/8" REF.
5-7/8" REF.
1/2" NPT
1/2" NPT
7-1/2"
9-1/2" REF.
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 65'' AND 78'
"SEE ILLUSTRATION "
Certified to comply with ANSI A112.18.1
ROUGHING-IN DIMENSIONS (For reference only)
To assure proper positioning in relation to wall, note roughing-in dimensions.
PRESSURE BALANCING BATH
AND SHOWER TRIM KIT
GREEN TEA
Installation
Instructions
T010.5XX
THREADED INLETS (STOPS)
INLETS
1/2" NPT
5-7/8"
INLETS 1/2" NPT
OUTLETS
1/2" NPT
OUTLETS
1/2" NPT
3-3/8"
3-3/8"
3-3/8"
THREADED INLETS
SHR. 1/2" NOM.
COPPER SWEAT
TUB 1/2" NOM.
COPPER SWEAT
4-1/16"
5-7/8"
INLETS
4-1/16"
4-1/16"
INLETS
1/2" NOM.
COPPER
SWEAT
SHR. 1/2" NOM.
COPPER SWEAT
TUB 1/2" NOM.
COPPER SWEAT
2"
SWEAT
INLETS
SWEAT
INLETS (STOPS)
INLETS
1/2" NOM.
COPPER
SWEAT
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
4-3/16"
Page 2
M968592 Rev.1.1 M968592 Rev.1.1 M968592 Rev.1.1
1
INSTALL VALVE TRIM
1
Figure 1.
Figure 2. Figure 3.
3
5
6
4
2
1
Figure 1. Remove plaster guard from valve. Push CAP (1)
over VALVE CARTRIDGE (2) until seated against stop.
Figure 2. Push ESCUTCHEON HOLDER (3) onto CAP (1)
and attach with LONG SCREWS (4). Mount ESCUTCHEON
SUPPORT (5) to ESCUTCHEON HOLDER (3) with 4 SHORT
SCREWS (6).
Figure 3. Align PINS (7) on back side of ESCUTCHEON (8)
with the FOUR HOLES (9) in ESCUTCHEON SUPPORT (5)
and press ESCUTCHEON (8) flush against finished wall.
PLSTER
GUARD
9
5
PIPE
PLUG
PIPE
CAP
1
4
3
2
SHR.
ELBOW
1/2" NPT
TUB NIPPLE
4-1/8"
REF.
Remove pipe cap and plug from shower and tub
rough piping. Apply Sealing tape to SHOWER ARM (3)
and tub filler pipe.
Install SPOUT ESCUTCHEON (5) onto SPOUT (1) and thread
SPOUT (1) onto tub nipple. Tighten SPOUT (1) and slide
ESCUTCHEON (5) flush agasinst finished wall.
CAUTION: Protect finish on TUB SPOUT (1) when installing.
Install SHOWER ESCUTCHEON (2) onto SHOWER
ARM (3). Thread SHOWER ARM (3) into shower elbow
and tighten. Slide ESCUTCHEON (2) flush agasinst
finished wall.
Thread SHOWER HEAD (4) onto SHOWER ARM (3).
5
2
INSTALL TUB SPOUT, SHOWER HEAD,
SHOWER ARM WITH FLANGE
CAUTION: Protect finish on SHOWER HEAD and
ARM when installing.
CAUTION: Protect finish on SHOWER
HEAD and TUB SPOUT when installing.
7
8
Page 3
SERVICE
5
Remove HANDLE (1), CAP (2) and CARTRIDGE (4). Clean inlets
and MANIFOLD (5).
Reassemble CARTRIDGE (4), alternately tightening SCREWS (3).
Replace CAP (2) and HANDLE (1). Check flow.
If faucet drips, operate handle several times from "off"
to "on". Do not apply excessive force.
Clogged CARTRIDGE (4) inlets may cause reduced flow in "full
on" hot or cold. To clean inlets, first turn off water supply, then:
5
4
3
2
1
6
"B"
"B"
3
ADJUST HOT LIMIT STOP
By restricting handle rotation and limiting the amount
of hot water allowed to mix with the cold, the HOT LIMIT
SAFETY STOP reduces risk of accidental scalding. To set
the maximum hot water temperature of your faucets, all
you need to do is adjust the setting on the HOT LIMIT
SAFETY STOP.
Use a flat blade screwdriver or your fingers to pull
up and rotate red HOT LIMIT SAFETY STOP (1).
Follow Step "A" or "B" to adjust min./max. discharge
temperature. "0" being the hottest to "7" the coldest
temperature setting. Factory set at "0".
HOT LIMIT SAFETY STOP ADJUSTMENT
PRY RED RING
FORWARD AND ROTATE
COUNTER-CLOCKWISE
ONE CLICK
PRY RED RING
FORWARD AND
ROTATE CLOCKWISE
"A"
"A"
ADJUSTMENT WHEN
WATER IS TOO HOT
ADJUSTMENT WHEN
WATER IS TOO COLD
"RED RING"- HOT
LIMIT SAFETY STOP
TEMPERATURE
SETTING
NUMBERS
1
0
1
2
3
4
5
6
1
2.5MM HEX
WRENCH
4
HANDLE INSTALLATION
3
Install HANDLE (1) by pushing it onto CARTRIDGE STEM (2)
and tightening SET SCREW (3) from below with 2.5mm
Hex Wrench supplied.
2
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
Page 4
PRESSURE BALANCE
BATH/SHOWER TRIM KIT
MODEL NUMBER
M962627-YYY0A
SHOWER ARM
AND FLANGE
M950203-YYY0A
DIVERTER SPOUT (1/2" NPT)
M950204-YYY0A
SHOWER HEAD
GREEN TEA
T010.5XX
M907050-YYY0A
CAP
M962625-YYY0A
ESCUTCHEON AND SEAL
M962626-YYY0A
HANDLE
M962427-0070A
ESCUTCHEON HOLDER
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Pr od uct n ame s li ste d her ei n are t rad em ar ks of Am er ic an St and ar d Inc .
© AS Am er ica , In c. 20 07
IN MEXICO 01-800-839-12-00
CHROME 002
Replace the "YYY" with
appropriate finish code
Loading...