American Standard 7196, 7183, 7145, 7172, Palisade 7103 User Manual

...

Download

Page 1

™

Installation Instructions

SILHOUETTE™ KITCHEN SINKS

MODELS 7145, 7163, 7172, 7179, 7183, 7185, 7196

PALISADE™ KITCHEN SINK

MODEL 7103

LAKELAND™ KITCHEN SINK

MODEL 7173

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

AMERICAST BRAND SELF RIMMING

Certified to comply with ANSI A112.19.4.M U.S. Patent No. 4,664,982 Other patents pending. CAN/C.S.A. B-45 Observe local plumbing and building codes.

790715-100 Rev. S

BEFORE YOU BEGIN...

Refer to American Standard roughing-in information for

specific dimensions for each model.

Unpack new sink and inspect carefully for damage. Replace the sink in its original packing carton to protect it until you are ready to begin installation.

Recommended Tools & Materials

Below are the dimensions needed to determine the cutout size for each sink. Select the correct diagram for your sink and refer to the instructions below.

CUTOUT DIMENSIONS FOR SINKS:

Locate and mark center lines of sink on countertop.

Silicone Sealant Putty Knife Pipe Wrench Channel Locks Phillips Screwdriver Regular Screwdriver Adjustable Wrench

(838mm)

(559mm)

5/8

(16mm)

SILHOUETTE DOUBLE BOWL SINK

SHALLOW SILHOUETTE DOUBLE BOWL SINK

(559mm)

(16mm)

SILHOUETTE TRIPLE BOWL SINK

IMPORTANT: DIMENSION OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE OF TOLERANCES ESTABLISHED BY A.N.S.I. AND C.S.A. STANDARDS

MODEL 7145

MODEL 7163

SILHOUETTE SINK

MODEL 7179 DUAL LEVEL

41-1/2

(1054mm)

5/8

MODEL 7183

CUTTING LINE

1" R TYP.

Drill Basin Wrench Saber Saw Tubing Cutter Tape Measure Hacksaw Mineral Spirits

1" R (25mm) TYP.

5/8 (16mm)

SINK OUTLINE

5/8 (16mm)

SINK OUTLINE

CUTTING LINE

Provide proper clearance under the countertop for the faucet supply lines and the structural parts of the cabinet.

By using the diagrams below and measuring your sink, draw the outline of the sink onto the countertop. This is not the cutting outline.

Refer to the diagram for your sink and draw a line 5/8" (16mm) in from the sink outline. Cut on this line.

(635mm)

(559mm)

5/8

(16mm)

SILHOUETTE

SINGLE BOWL SINK

MODEL 7172

(965mm)

(559mm)

5/8

(16mm)

SILHOUETTE DUAL LEVEL SINK

MODEL 7196

1" R (25mm) TYP.

5/8 (16mm)

SINK OUTLINE

CUTTING LINE

5/8 (16mm)

1" R TYP.

SINK OUTLINE

CUTTING LINE

(457mm

(457mm)

5/8

(16mm)

SILHOUETTE ISLAND SINK

MODEL 7185

(787mm)

19-1/2

(495mm)

5/8

(16mm)

PALISADE SINGLE BOWL

MODEL 7103

(787mm)

(559mm)

5/8

(16mm)

LAKELAND SINGLE BOWL

MODEL 7173

©AMERICAN STANDARD INC. 2004

1" R (25mm) TYP.

CUTTING LINE

5/8 (16mm)

SINK OUTLINE

1" R (25mm) TYP.

5/8 (16mm)

SINK OUTLINE

1" R (25mm) TYP.

5/8 (16mm)

SINK OUTLINE

Page 2

AFTER THE CUTOUT IS DRAWN...

Drill a clearance hole inside the cutout line as marked on the countertop.

Cut opening on cut line inside the perimeter of

sink. Note - Formica countertop installation only is illustrated. Contact your countertop distributor for the best method of cutting other materials such as marble, hard synthetics, etc.

Mount the faucet and

drain assembly on the sink or countertop following the manufacturer's instructions.

Before applying the sealant, place the sink temporarily

into the cutout. Check for alignment and clearance, then trace around the outside edge of the sink as a guide for installation location and application of sealant.

Perimeter of sink

Cutout

Remove sink and apply

Cutout

a masking tape outline 1/8" outside traced outline as a guide for application of silicone sealant.

Apply a generous portion of silicone sealant inside line

traced on countertop. Carefully lower sink into place

Masking tape outline

1/8"

and press down firmly. Use guidelines for proper positioning. Using water to dampen your finger, remove excess sealant for a smooth even line. Apply additional sealant if necessary to provide a uniform bead from the rim of sink to the masking tape line as shown. Carefully remove tape. Dampen finger and run it slightly over the sealant to remove any high spots. Use mineral spirits to remove excess silicone from countertop and sink.

Masking Tape

Silicone Sealant

Sink

NOTE: Silicone must be removed within 10 minutes of application or a permanent residue may remain on the surfaces.

Connect supply lines to

faucet finger tight, and carefully bend to engage with the supply stops. Tighten connections to faucet for secure seal.

Sink outline

If an American-Standard Americast® brand product is found to be defective in materials or workmanship, after inspection by an authorized American-Standard representative, American-Standard will repair or, at its option, exchange the product for a similar model. This warranty extends for the lifetime of the product, so long as it remains in use in its original place of installation, except that the warranty applies to a bathing vessel’s slip-resisting surface only for the first year after the product’s initial installation.

This warranty applies only to the original purchaser and installation of these products.

This warranty does not apply to whirlpool components or to faucets, drains, mounting rims, grab bars or other accessories. If manufactured or supplied by AmericanStandard, such whirlpool components and accessories are covered under separate limited warranties.

This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing contractor to assure local code compliance before installation.

This warranty shall be void if the Americast® brand product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with AmericanStandard’s instructions; or if it was modified in a manner inconsistent with the product as shipped by American-Standard.

American-Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall American-

Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or provinces do

not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.) This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this warranty does not affect such statutory rights.

For service under these warranties, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address:

Attention: Director of Consumer Affairs

For residents of the United States, warranty information may also be obtained by calling

the following toll free number: (800) 442-1902

AMERICAST® LIMITED LIFETIME WARRANTY

In the United States:

American Standard Inc.

P.O. Box 6820

Piscataway, New Jersey 08855

www.AmericanStandard-US.com

In Canada:

American Standard

2480 Stanfield Rd.

Mississauga, Ontario

Canada L4Y 1S2

Toll Free: (800) 387-0369

www.AmericanStandard.ca

Connect drain assembly

hand tight to check alignment. It may be necessary to cut off part of the tailpiece (area "A") or part of the

horizontal leg of the trap (area "B").

Secure joint for watertight assembly.

Trap

Single Bowl Double Bowl

CARE AND CLEANING...

For all porcelain enamel surfaces, regular, gentle care is best. The recommended way to preserve the finish, avoid scratches, and clean porcelain enamel fixtures is to rinse them with detergent and water. Generally, any of the light duty liquid dishwashing detergents, such as Palmolive or Dawn, work well. In areas where the water is hard, a heavy duty liquid laundry detergent such as liquid Tide will work better.

Product names listed herein are trademarks of American Standard Inc.unless otherwise noted.

Palmolive® is a registered trademark of Colgate-Palmolive Co.

Tide® and Dawn® are registered trademarks of Procter and Gamble.

In Mexico:

Customer Service Manager

Ideal Standard, S.A. de C.V.

Via Morelos #330

Col. Santa Clara

Ecatepec 55540 Edo. Mexico

www.AmericanStandard.com.mx

Trap

790715-100 Rev. S