Page 1
AittM'emi Skmhrd
Installation
Instructions
ONE
T064.60X
BATH/SHOWER TRIM KIT WITH DIVERTER
Congratulations on purchasing your American Standard faucet with
EverClean™ finish a features found oniy on American Standard faucets.
EverClean™ Finish
• One wipe effortlessly removes spots.
• Eliminates the need for cleaners and scrubbing.
• Permanent surface protectant remains beautiful
for the life of the faucet.
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)
To ensure that your installation proceeds smoothly-please read these
instructions carefully before you begin.
Required Tools
Flat Blade Screwdriver
Pipe Wrench
ROUGHING-IN DIMENSIONS
■ To assure proper positioning in relation to wall, note
roughing-in dimensions.
Phillips Screwdriver Plumbers' Putty or Caulking Adjustable Wrench
-►M-5/8" TO 3-1/4"
Certified to compiy with ANSI A112.18.1
M968836
Channel Locks
5-5/8" REF.
74"FOR
HEAD CLEARANCE
OPTIONAL
FINISHED WALl^
18"
TOP OF^
TUB RIM \
BOTTOM OF
f
8-1/8" REF.
7-1/4" □. ac
h
-----
8-3/4"-
TUB
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
80" AND 86'
4-'
"SEE ILLUSTRATION"
1/2" NPT
1/2" REF.
4"
^ OUTLETS 1/2" NPT
INLETS
1/2" NPT
THREADED INLETS (STDPS)
Page 2
INSTALL DIVERTER
When finished tiling the wall, remove PLASTER GUARD (1).
Remove two screws that secure the DIVERTER LID (2) and
remove Lid. Inspect the inside surface of diverter port.
Diverter port must be free of any dirt. Clean if necessary.
Install DIVERTER (3) with SCREWS (4) removed with
DIVERTER LID (2).
Operate DIVERTER (3). DIVERTER (3) should slide in
and out smoothly.
INSTALL VALVE TRIM
DIVERTER
PORT
Figure 1. Push CAP (1) over VALVE CARTRIDGE (2) until
seated against stop. Push CAP (3) over DIVERTER (4) until
seated against stop.
Figure 2. Push ESCUTCHEON HOLDER (5) onto CAP(1J
and attach with SCREWS [S). Mount ESCUTCHEON
SUPPORT (7J to ESCUTCHEON HOLDER (5) with
SCREWS (8).
Figure 3. Align PINS (10) on back side of ESCUTCHEON (11)
with the FOUR HOLES (12) in ESCUTCHEON SUPPORT (7)
and press ESCUTCHEON (11) flush against finished wall.
Figure 1.
Figure 2.
M968836
Page 3
ADJUST HOT LIMIT STOP
By restricting HANDLE rotation and limiting the amount of hot
water allowed to mix with the cold, the HOT LIMIT SAFETY
STOP 11J reduces risk of accidental scalding. To set the maximum
hot water temperature of your faucet, all you need to do
is adjust the setting on the HOT LIMIT SAFETY STOP llj.
Turn CARTRIDGE STEM (2) to the OFF position [coldest setting)
before making adjustment to HOT LIMIT STOP (1). Use a flat
blade screwdriver to pry free the HOT LIMIT SAFETY STOP (1J.
Pull forward and rotate counterclockwise one number to limit hot
water temperature. Use ARROW (3) on CARTRIDGE (4)
and NUMBERS (5) on HOT LIMIT STOP (1J for
indication.
(Larger Numbersl
□ 1 3 5 719 11 13 15l
INSTALL HANDLE, DIVERTER KNOB, TUB
O
SPOUT AND SHOWER
■ Thread DIVERTER KNOB (1) onto diverter stem.
■ Hold ADAPTER (2) onto VALVE STEM (3) and install
ADAPTER SCREW (4) through ADAPTER (2) into
VALVE STEM (3J.Tighten ADAPTER SCREW (4) to
secure ADAPTER (2) to VALVE STEM (3).
■ Install HANDLE BASE (5) onto ADAPTER (2). Insert
SET SCREW (S) into HANDLE BASE (5). Align
HANDLE BASE (4) and tighten with HEX WRENCH
(7) supplied.
■ Thread LEVER HANDLE (8) into HANDLE BASE (5).
■ Remove pipe cap and plug from shower and tub
rough piping.
■ Install SPOUT ESCUTCHEON (8) onto TUB SPOUT IIO).
■ Apply sealant or Teflon tape to threads of tub filler
nipple. Thread TUB SPOUT (10) onto tub nipple.
■ Install SHOWER ESCUTCHEON (11) onto SHOWER
ARM (12). Apply sealant or Teflon tape to threads on
both ends of SHOWER ARM (12) and thread longer
leg of SHOWER ARM (12) into shower elbow.
■ Thread SHOWER HEAD (13) onto SHOWER ARM (12).
CAUTION: Protect finish on SHOWER HEAD and
ARM when installing.
TO GAIIM ACCESS TO VALVE FOR SERVICING
Unthread LEVER HANDLE, loosen SET SCREW and pull
HANDLE off valve stem.
To remove Escutcheon assembly reverse steps in Step 3.
VALVE LEAKS WHEN SHUT OFF
Remove CARTRIDGE (1) by removing CARTRIDGE SCREWS (2).
Remove three SCREWS (3) from FIXATION RING (4) and pull
out PRESSURE BALANCING (5) unit.
Clean SEALS (S) on base of CARTRIDGE (1). Check base of
PRESSURE BALANCING UNIT (5) and clean 0-RINGS (6). Remove
CAPS (7J and check D-RINGS on inside of CAPS (7J. Clean inside
sealing surfaces of VALVE BODY (8).
Reessemble PRESSURE BALANCING UNIT (5) and CARTRIDGE (1J.
Tighten all screws.
Turn on water supply and see above for installing TRIM and HANDLE.
UNABLE TO MAINTAIN CONSTANT TEMPERATURE
Remove PRESSURE BALANCE UNIT (5). Remove CAPS (7) and
clean valve thoroughly.
Examine balancing unit and check condition of 0-ring on end of
piston. Piston should move back and forth. Order Repair
Part M952100-0070A if balancing unit is defective.
Replace CAPS (7) and install PRESSURE BALANCE UNIT (5).
Make sure inlets line up with two holes in bottom of casting.
Top flange should butt-up against top of casting.
BACK TO BACK INSTALLATION
Remove PRESSURE BALANCE UNIT (5). Rotate PRESSURE BALANCE UNIT (5) 1 B0‘ so that the inlets face up and the
large outlet port faces down.
Push PRESSURE BALANCE UNIT (5) in casting make sure inlets line up with holes in bottom of casting. Top flange should
butt up against top of casting.
Reassemble FIXATION RING (4) and CARTRIDGE HJ.
ROTATE 180'
SHR.
ELBOW
BACK TO BACK INSTALLATION
M968836
Page 4
Лмпст Skmia^xl
M9G2818-YYY0A
DEEP ROUGH KIT
(NOT SHOWN]
ONE
BATH/SHOWER TRIM KIT
WITH DIVERTER
MODEL NUMBER
T064.60X
M982493-YYY0A
SHOWER ARM & FLANGE
M953540-YYY0A
SHOWER HEAD
M962494-0070A
ESCUTCHEON HOLDER
Replace the "YYY" with
appropriate finish code
CHROME GG2
SATIN NICKEL
295
M907053-YYY0A -
CAP
M962495-YYY0A
TUB SPOUT ESCUTCHEON
M918039-0070A-
HANDLE ADAPTER
M962209-YYY0A
SPOUT KIT
M9G242G-YYY0A-
HANDLE KIT
A950849-YYY0A
ESCUTCHEON
WITH DIVERTER
M909917-YYY0A
DIVERTER KNOB
I—A918477-0070A
HANDLE SCREW
922388-YYYOA
STREAM STRAIGHTENER
For toll-free Informetlon end enswers to your questions, cell:
IN CANADA 1-800387-0389 (TORONTO 1-905-306-1093)
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2006
HOT LINE FOR HELP
1 [800)442-1902
Weekdays 8:00 e.m. to 8:00 p.m. EST
IN MEXICO 01-800939-12-00
Weekdays 8:00 e.m. to 7:00 p.m. EST
M968836
Loading...