American Standard 4114.003, 4114.001 User Manual
Installation
LAKELAND
SINGLE CONTROL KITCHEN
FAUCET WITH CAST SPOUT
Instructions
4114.001
4114.003
with EverClean™ Finish
Congratulations on purchasing your American Standard faucet with
EverClean nish found only on American Standard faucets.
EverClean Finish
• One wipe eortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel, Stainless Steel, Polished Brass (or any combination of these nishes)
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
TOOLS REQUIRED
3FHVMBS4DSFXESJWFS
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
CAUTION
(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Insert supply HOSES (2) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface.
Follow mounting instructions below to secure faucet to mounting surface.
Turn off hot and cold water
supplies before beginning.
Phillips Screwdriver
Adjustable Wrench
Certified to comply with ANSI A112.18.1M
.3&7
Plumbers' Putty or Caulking
(B) Installation less ESCUTCHEON (1). Discard ESCUTCHEON with PUTTY PLATE (1). Insert supply HOSES (2) and
SHANK (3) through mounting hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
7
1
PUTTY
7
A
SPOUT BASE
2
3
B
3
2
SINK OR
4
5
8
6
MOUNTING
SURFACE
8
4
5
6
MAKE WATER SUPPLY CONNECTIONS
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply to Hot (Marked with a Red Line)
and right supply to Cold wall supply. Use
adjustable wrench to tighten connections.
Do not over tighten.
Faucet supplies are 21" long from faucet base.
Note: If additional supply length is
required, installer must purchase
additional parts separately.
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
INSTALL SPRAY HOLDER
On model with separate spray, place the SPRAY HOLDER (1)
into the appropriate mounting hole. Assemble the SPRAY
HOLDER WING NUT (2) onto the shank of SPRAY HOLDER (1)
from below and hand tighten. Do not use putty.
On model with spray through the ESCUTCHEON (3), place
SPRAY HOLDER (4) into the hole of ESCUTCHEON (3). Assemble
SPRAY HOLDER NUT (5) onto the shank of SPRAY HOLDER (4)
from below and hand tighten. Do not use putty.
For installation less spray, cap off SPRAY HOSE
CONNECTION (9) with PIPE CAP (6).
1
SPRAY HOSE
CONNECTION
2
COLD
HOT
1
7
9
CONNECT HOSE SPRAY
Feed SPRAY HOSE (7) through SPRAY
HOLDER (1) and attach COUPLING NUT (8)
of HOSE (7) to SPRAY HOSE CONNECTION (9)
on valve body. Tighten COUPLING NUT (8)
firmly.
TEST INSTALLED FAUCET
Move HANDLE down into "off" position and remove
AERATOR (1).
Turn on water supplies and check connections for leaks
Operate HANDLE (2) up and down, left and right to flush
water lines thoroughly.
For faucet with spray, direct SPRAY HEAD (3) into sink and
activate SPRAY (3). Check hose connections for leaks.
Move HANDLE (2) down to "off" position and replace AERATOR (1).
4
5
.
3
2
8
6
2
3
1
CHECK CONNECTIONS
FOR LEAKS
.3&7
Loading...