American Standard 4101.350, 4101.351 User Manual
Installation
Instructions
ARCH
4101.350
4101.351
HI-FLOW PULL-OUT
KITCHEN FAUCET
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
RECOMMENDED TOOLS
Adjustable Wrench Regular Screwdriver Phillips Screwdriver
INSTALL FAUCET WITH DECK ESCUTCHEON
1
(4101.351)
Installation with DECK ESCUTCHEON: Apply a light bead of plumbers putty to underside of ESCUTCHEON (1) if
mounting surface is uneven. Place ESCUTCHEON (1) onto sink or mounting surface with large opening
to the right as shown. Insert supply HOSES (2) and SHANK (3) through ESCUTCHEON (1) and mounting surface.
Make sure slot in fitting base aligns with tab on ESCUTCHEON (1). Figure 1.
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening the
SCREWS (8) slightly each time until all are snug to ensure even pressure.
Install SPOUT ASSEMBLY: Insert HOSE (9) and SHANK (10) through ESCUTCHEON (1) and mounting surface.
Make sure slot in spout base aligns with tab on ESCUTCHEON (1). Figure 2.
Assemble RUBBER WASHER (4a), BRASS WASHER (5a), and threaded LOCKNUT (6a) onto SHANK (10) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6a). Use a screwdriver to tighten SCREWS (8a) on LOCKNUT (6a)
the same as fitting installation above.
Align SOAP DISH (11) and push into place.
CAUTION
Turn off water at
main supply.
4101.351 4101.350
Certified to comply with ANSI A112.18.1M
M968584
Channel Locks
7
Figure 1 Figure 2
SLOT
3
ALIGN SLOT
1
2
4
TAB
5
6
8
AND TAB
11
1
ALIGN SLOT
AND TAB
4a
SLOT
TAB
8a
10
5a
6a
9
1a
INSTALL FAUCET WITHOUT ESCUTCHEON PLATE
(4101.115 with soap dish) (4101.350 less soap dish)
Insert SEAL WASHER (1) into ESCUTCHEON (2). Place ESCUTCHEON (2) onto sink or mounting surface. Insert supply
HOSES (3) and SHANK (4) through ESCUTCHEON (2) and mounting surface.Make sure slot in fitting base aligns with
tab on ESCUTCHEON (2). Figure 1.
Assemble RUBBER WASHER (5), BRASS WASHER (6) and threaded LOCKNUT (7) onto SHANK (4) from underside
of sink or mounting surface. Hand tighten LOCKNUT (7) and check that rotation of HANDLE (8) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (9) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening the
SCREWS (9) slightly each time until all are snug to ensure even pressure.
Install SPOUT ASSEMBLY: Insert SEAL WASHER (1a) into ESCUTCHEON (2a). Insert HOSE (10) and SHANK (11)
through ESCUTCHEON (2a) and mounting surface. Make sure slot in spout base aligns with tab on ESCUTCHEON (2a).
Figure 2.
Assemble RUBBER WASHER (5a), BRASS WASHER (6a), and threaded LOCKNUT (7a) onto SHANK (11) from underside
of sink or mounting surface. Hand tighten LOCKNUT (7a). Use a screwdriver to tighten SCREWS (9a) on LOCKNUT (7a)
the same as fitting installation above.
(4101.115 with soap dish) Push SOAP DISH (11) into SOAP DISH SHANK (12). Insert SOAP DISH ASSEMBLY into
mount hole. From underside of counter assembly LOCKNUT (13) onto SOAP DISH SHANK (12).
Align SOAP DISH (11) and tighten LOCKNUT (13).
8
Figure 1
4
3
2
1
Figure 2
SLOT
ALIGN SLOT
AND TAB
TAB
ALIGN SLOT
AND TAB
SLOT
11
11
TAB
12
5
6
1a
2a
7
9
13
5a
9a
6a
7a
10
MAKE WATER SUPPLY CONNECTIONS
2
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect left supply (Marked with a Red Stripe)
to Hot and right supply (Marked with Blue Stripe) to Cold wall supply. Use adjustable
wrench to tighten connections. Do not over tighten.
Faucet supplies are 21" long from faucet base.
Note: If additional supply length is required, installer must purchase
those parts separately.
Important: If SUPPLY HOSES (1, 2) are too long, loop as illustrated to avoid kinking.
2
1
HOT
COLD
M968584
Loading...