Page 1
Installation
Instructions
ARCH
4101.301
HI-FLOW KITCHEN FAUCET
with SIDE SPRAY
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
RECOMMENDED
TOOLS
Adjustable Wrench Regular Screwdriver Phillips Screwdriver
INSTALL FAUCET WITH DECK ESCUTCHEON
1
(4101.351)
Installation with DECK ESCUTCHEON: Apply a light bead of plumbers putty to underside of ESCUTCHEON (1) if mounting
surface is uneven. Place ESCUTCHEON (1) onto sink or mounting surface with large opening to the right as shown. Insert
supply HOSES (2) and SHANK (3) through ESCUTCHEON (1) and mounting surface. Make sure slot in fitting base aligns
with tab on ESCUTCHEON (1). Figure 1.
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening the
SCREWS (8) slightly each time until all are snug to ensure even pressure.
Install SPRAY HOLDER: Insert SPRAY HOLDER (11) into ESCUTCHEON (1). From underside of sink or mounting surface
thread LOCKNUT (12) onto SPRAY HOLDER (11) shank and tighten.
CAUTION
Turn off water at
main supply.
4101.301 shown with
optional escutcheon 4101.000P
Certified to comply with ANSI A112.18.1M
4101.301
M968583
Channel Locks
Install SPOUT ASSEMBLY: Insert SPRAY HOSE (9) and SHANK (10) through ESCUTCHEON (1) and mounting surface.
Make sure slot in spout base aligns with tab on ESCUTCHEON (1). Figure 2.
Assemble RUBBER WASHER (4a), BRASS WASHER (5a), and threaded LOCKNUT (6a) onto SHANK (10) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6a). Use a screwdriver to tighten SCREWS (8a) on LOCKNUT (6a)
the same as fitting installation above.
7
Figure 1
SLOT
Figure 2
3
TAB
ALIGN SLOT
AND TAB
ALIGN SLOT
AND TAB
SLOT
10
TAB
11
1
2
12
4
5
1
6
8
4a
8a
5a
6a
9
Page 2
1a
INSTALL FAUCET WITHOUT ESCUTCHEON PLATE
(4101.115 with soap dish) (4101.350 less soap dish)
Insert SEAL WASHER (1) into ESCUTCHEON (2). Place ESCUTCHEON (2) onto sink or mounting surface. Insert supply
TUBES (3) and SHANK (4) through ESCUTCHEON (2) and mounting surface.Make sure slot in fitting base aligns with
tab on ESCUTCHEON (2). Figure 1.
Assemble RUBBER WASHER (5), BRASS WASHER (6) and threaded LOCKNUT (7) onto SHANK (4) from underside
of sink or mounting surface. Hand tighten LOCKNUT (7) and check that rotation of HANDLE (8) from HOT to COLD
is centered.
Use a screwdriver to tighten SCREWS (9) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening the
SCREWS (9) slightly each time until all are snug to ensure even pressure.
Install SPRAY HOLDER: Insert SPRAY HOLDER (11) into ESCUTCHEON (12). Insert SEAL (14) into underside of
ESCUTCHEON (12). From underside of sink or mounting surface thread LOCKNUT (13) onto SPRAY HOLDER (11)
shank and tighten.
Install SPOUT ASSEMBLY: Insert SEAL WASHER (1a) into ESCUTCHEON (2a). Insert SPOUT HOSE (10) and SHANK (11)
through ESCUTCHEON (2a) and mounting surface. Make sure slot in spout base aligns with tab on ESCUTCHEON (2a).
Figure 2.
Assemble RUBBER WASHER (5a), BRASS WASHER (6a), and threaded LOCKNUT (7a) onto SHANK (11) from underside
of sink or mounting surface. Hand tighten LOCKNUT (7a). Use a screwdriver to tighten SCREWS (9a) on LOCKNUT (7a)
the same as fitting installation above.
8
Figure 1
SLOT
Figure 2
4
ALIGN SLOT
AND TAB
11
3
2
TAB
ALIGN SLOT
AND TAB
1
12
14
5
13
6
7
9
MAKE WATER SUPPLY CONNECTIONS
2
Push HOSE END (1) with compression fitting onto COPPER TUBE (2) Make sure
HOSE and COPPER TUBE are fully engaged (approx.1/2" engagement). Use adjustable
wrench to tighten connections. Do not over tighten.
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (3) directly to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect left supply (Marked with a Red Stripe)
to Hot and right supply to Cold wall supply. Use adjustable wrench to tighten
connections. Do not over tighten.
Faucet supplies are 24-1/2" long from faucet base.
Note: If additional supply length is required, installer must purchase
those parts separately.
Important: If SUPPLY HOSES (3) are too long, loop as illustrated to avoid kinking.
SLOT
TAB
1a
5a
9a
11
2a
RED STRIPE
2
1
3
HOT
6a
7a
10
1/2"
ENGAGEMENT
COLD
M968583
Page 3
CONNECT SPRAY HOSE AND SPOUT HOSE
3
Feed HAND SPRAY HOSE (1) through SPRAY HOLDER (2).
Use wrench to tighten COUPLING NUT (3) on SPRAY HOSE (1)
to SIDE SPRAY CONNECTION (4) on fitting.
Make sure SEAL WASHER (5) is installed in COUPLING
NUT (6). Connect threaded end of HOSE (7) to SPOUT HOSE
COUPLING NUT (6) from fitting. Use wrench to tighten.
2
1
6
5
4
CHECK CONNECTIONS FOR LEAKS.
4
Move HANDLE (1) down into "off" position.
Turn on water supplies and check connections
for leaks
.
7
3
1
CHECK CONNECTIONS
FOR LEAKS
M968583
Page 4
TEST INSTALLED FAUCET
5
Move HANDLE (1) down into "off" position.
Remove AERATOR (2).
Operate handle up and down, in COLD and HOT positions,
to flush water lines thoroughly.
Replace AERATOR (2).
With HANDLE (1) down in "off" position, pull HAND SPRAY (3)
from holder and direct SPRAY END (3) into sink.
Check HAND SPRAY (3) operation:
With faucet on push BUTTON (4) to activate HAND SPRAY (3).
Release BUTTON (4) to stop spray and return
HAND SPRAY (3) to holder.
1
2
4
3
SERVICE
6
If faucet drips, operate HANDLE several times from "off" to "on." Do not
apply excessive force.
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
Remove INDEX BUTTON (1), loosen HANDLE SCREW (2)
and remove HANDLE (3).
Unthread ESCUTCHEON CAP (4). Unthread three
MOUNTING SCREWS (5).
Lift CARTRIDGE (6) off MANIFOLD (7) and remove
CARTRIDGE SEALS (8).
Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).
Place SEALS (8) into CARTRIDGE PORTS (6a).
Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING
SCREWS (5) alternately.
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE
SCREW (1) and install INDEX BUTTON (2).
Test fitting.
3
2
1
4
5
6
6a
8
7
CARE INSTRUCTIONS:
7
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
M968583
Page 5
M962715-YYY0A
AERATOR
M962717-YYY0A
HANDLE KIT
M962716-0070A
BUTTON AND
SCREW KIT
ARCH
HI-FLOW KITCHEN FAUCET
with SIDE SPRAY
MODEL NUMBERS
4101.301
M907305-YYY0A
CARTRIDGE COVER
M918521-0070A
CARTRIDGE SCREWS
A951470-0070A
CARTRIDGE
042850-0070A
DIVERTER
M953578-YYY0A
HAND SPRAY AND HOSE
M923651-YYY0A
SPRAY HOLDER
M907610-YYY0A
SPRAY ESCUTCHEON
(4101.301)
US61812-YYY0A
NUT
Replace the "YYY" with
appropriate finish code
CHROME
STAINLESS STEEL
(4101.301)
M962725-YYY0A
ESCUTCHEON KIT
(4101.301)
M962726-YYY0A
ESCUTCHEON KIT
WITH PUTTY PLATE
(4101.000P)
060467-0070A
MOUNTING KIT
M923276-0070A
SUPPLY HOSE
002
075
For toll-free information and answers to your questions, call:
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
HOT LINE FOR HELP
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-12-00
M962722-0070A
SPRAY HOSE
AND SEAL
M968583
Loading...