American Standard 3875-503, 3875-403 User Manual
Installation
Instructions
COLONY SOFT
3875.403
3875.503
Spread Lavatory Faucet with
SpeedConnect™ Drain
C
Congratulations on purchasing your American Standard faucet with
SpeedConnect drain, a feature found only on American Standard faucets.
H
SpeedConnect Drain*
• 1/3 of the parts, installs in 1/3 of the time
• No tools needed
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is designed to work only with the SpeedConnect drain.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Required tools
Adjustable Wrench Screwdriver Channel Locks
INSTALL SPOUT
1
Insert SPOUT (1) and CABLE CONNECTOR (2) through center hole, making sure
the SEAL WASHER (3) is properly seated in SPOUT (1).
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT
SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting
hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.
CAUTION
Turn off hot and cold water
supplies before beginning.
Tubing Cutter
Certified to comply with ANSI A112.18.1
M968886
Fig. A.
1
Tighten LOCKNUT (6) firmly. Fig. A.
1A
INSTALL VALVE BODY
Place RUBBER RING (9) into SCUTCHEON (10).
Install LOCKNUT (11) onto VALVE BODY (12).
From under side of mounting surface, install VALVE BODY (12) through valve
mounting holes. Threads of VALVE BODY (12) should extent at least 5/16
of a inch above mounting surface top. Fig. B. Thread ESCUTCHEON (10)
onto VALVE BODY (12) until snug against internal stop. If necessary, adjust
LOCKNUT (11).
Hand tighten LOCKNUT (11) to secure VALVE BODY (12). Repeat above steps
for opposite VALVE BODY (12A).
10
9
5/16'' MIN.
MOUNTING
SURFACE
10
9
Fig. B.
11
12
12
11
3
SLOT
7
4
5
6
2
12a
1
INSTALL POP-UP DRAIN
2
Remove CLEAR PLASTIC COVER (1). Remove
CARDBOARD SPACER (2) from under DRAIN
POP-UP (3).
Drop DRAIN BODY (4) through sink drain
hole. Make sure WHITE FOAM GASKET (5)
is under flange of DRAIN BODY (4).
Note: No plumber’s putty or caulk is required.
The CABLE ATTACHMENT POINT (6) must
face towards the rear of the SINK.
INSTALL BLACK GASKET
3
Install BLACK CONE GASKET (1) onto DRAIN BODY (2)
from below.
Note: The flat side of the BLACK CONE GASKET (1) must
face down.
Fig. A.
Fig. B.
Fig. B.
Fig. A. Fig. B.
1
3
2
2
REAR OF
SINK
4
6
5
SINK
DRAIN
HOLE
INSTALL GRAY LOCKNUT
4
Install GRAY LOCKNUT (1) onto DRAIN BODY (2)
from below SINK. Fig. A.
Note: The flat side of the GRAY LOCKNUT (1)
must face up.
Tighten firmly by hand. No tools are required.
Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. B.
POP-UP KNOB
5
POP-UP KNOB (1) must be fully down.
Fig. A.
1
FLAT SIDE OF GASKET
MUST FACE DOWN
Fig. B.
2
DRAIN
FLANGE
FLAT SIDE OF
GRAY LOCKNUT
MUST FACE UP
WHITE FOAM
DOWN
3
GASKET
NOT VISIBLE
1
1
M968886
2
Loading...