American Standard 6032Y1.ST-R.XXX, 6032Y1.ST-L.XXX, 4834Y1.ST.XXX, 3838Y1.DT.XXX, 3232Y1.ST.XXX User Manual
...
INSTALLATION INSTRUCTIONS
Acrylux Builder Series Shower Bases
Model 3232Y1.ST.XXX
Model 3636Y1.ST.XXX
Model 4834Y1.ST.XXX
Model 3838Y1.NEO.XXX
Model 6032Y1.ST-L.XXX
Model 6032Y1.ST-R.XXX
Model 6032Y1.ST-C.XXX
Model 3838Y1.DT.XXX
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please
read these instructions carefully before you begin. Local building codes vary by location. Observe all local plumbing and building codes.
1"
(25mm)
3232Y1.ST.XXX
31-5/8"
(803mm)
4834Y1.ST.XXX
STUD LAYOUT:
Shower base will fit all standard 32" x 32"
3636Y1.ST.XXX
shower walls.
1"
5-1/8"
(130mm)
31-7/8"
(810mm)
33-1/2"
(851mm)
16"
(406mm)
= stud location = stud location
14-3/4"
(375mm)
Drain C
Floor
Cutout
(6" x 6")
(152mm x 152mm)
32"
(813mm)
L
(25mm)
35-7/8"
(911mm)
6032Y1.ST-L.XXX
STUD LAYOUT:
Shower base will fit all standard 36" x 36"
shower walls.
5-1/8"
(130mm)
37-1/2"
35-7/8"
(911mm)
(953mm)
18"
(457mm)
(152mm x 152mm)
36"
(914mm)
16-1/2"
(419mm)
Drain C
Floor
Cutout
(6" x 6")
5-1/8"
(130mm)
L
6032Y1.ST-R.XXX
15"
6"
L
1"
(25mm)
31-1/4"
(794mm)
6"
(152mm)
30"
(762mm)
(1524mm)
CENTER DRAINLEFT DRAIN
60"
15"
(381mm)
C
L
15"
(381mm)
6"
(152mm)
Drain C
L
RIGHT DRAIN
59-7/8"
(1521mm)
12"
(305mm)
9"
(229mm)
1"
(25mm)
(845mm)
33-1/4"
= stud location
47-7/8"
(1216mm)
35-1/2"
(902mm)
5-1/8"
(130mm)
STUD LAYOUT:
Shower base will fit all
standard 34" x 48"
shower walls.
24"
(610mm)
(1219mm)
16-3/4"
(425mm)
Drain C
L
Floor
Cutout
(6" x 6")
(152mm x 152mm)
48"
6032Y1.ST-C.XXX
STUD LAYOUT:
Shower bases will fit all
standard 32" x 60"
shower walls.
12"
33-1/2"
(838mm)
stud
=
location
(305mm)
(229mm)
(381mm)
9"
Drain C
(152mm)
3838Y1.NEO.XXX
STUD LAYOUT:
Shower base will fit all
standard 38" neo-angle
shower walls.
5-1/8"
(130mm)
39-1/2"
(1003mm)
1"
(25mm)
(965mm)
19-1/2"
(495mm)
38"
26"
(660mm)
38"
(965mm)
19-1/2"
(495mm)
= stud location = stud location
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2008
12"
(305mm)
Floor
Cutout
6"
(152mm)
12"
(305mm)
10"
(254mm)
39-1/2"
(1003mm)
1"
(25mm)
3838Y1.DT.XXX
38"
(965mm)
38"
(965mm)
5-1/8"
(130mm)
39-1/2"
(1003mm)
STUD LAYOUT:
Shower base will fit all
standard 38" corner entry
shower walls.
18"
(457mm)
Floor
Cutout
6"
(152mm)
18"
(457mm)
10"
(254mm)
39-1/2"
(1003mm)
754285-100 Rev. A
IMPORTANT
• Allow base to reach room temperature before installation.
• Before you begin, locate appropriate product reference (see page 1).
• Read installation instructions carefully before starting project.
• Keep instructions for warranty information
RECOMMENDED TOOLS AND MATERIALS
Tape Measure Pencil Saber Saw Personal Safety Equipment
Mortar Mix (optional) Drill 24" Level Screws, 1" Flathead, Stainless
INSTALLATION INSTRUCTIONS
STEP 1. PREPARING ALCOVE
• Strip alcove to bare studs.
• Alcove studs should be constructed as shown above.
• Floor must be clean, smooth, and level (check with level). Sub floor must be
installed. Do not install shower base on open floor joists.
• Cut hole in sub floor as shown on page 1 to accommodate drain.
STEP 2. INSTALLING BASE
• Trial fit base in prepared alcove. With base sitting flat on floor, check with level
on top of base. Base should be level from front-to-back and side-to-side (Fig 1).
If base is not level, remove base and level floor using leveling compound.
• A floor leveling compound (smooth mortar) or a similar quick-setting compound
specifically made for leveling floors may be used to fully support and level base.
• After base is leveled, if alcove is larger than base, shim between base and studs
to create a tight fit. Screw base flange to studs (Fig. 2).
CLEANING
• Do not use any abrasive cleaners or metal scrapers.
• If drywall mud or plaster gets on your shower, it may be carefully
removed with a wooden scraper made from a piece of scrap wood.
• Adhesive may be removed with mineral spirits.
®
• Ideal cleaners are Soft Scrub Gel
or Comet Gel®.
FIGURE 1. Check to assure base is level.
FIGURE 2. If necessary, shim between base and
studs for tight fit and screw to each stud.
WARNING: Some cleaning products are not suitable for use. Read all labels carefully.
DO NOT USE if they say “not suitable for use with ABS, acrylic or polystyrene”.
754285-100 Rev. A-2-
Loading...