American Standard 0211.100, 0211.008, 0211.800, 0211.400, 3801.452 User Manual

FINI SHED WALL

206mm

(8-1/8)

C/L

508mm

(20)

108mm

(4-1/4)

10mm

(3/8)

203mm

(8)

140mm

(5-1/2 REF.)

552mm (21-3/4)

70mm (2-3/4)

660mm

(26)

PEDE STAL A NCHOR ING SCRE W HOLE S

8mm (5/16 ) DIA.

PEDE STAL TO W ALL CLEA RANCE

FINISHED FLOOR

210m m (8-1 /4)

260m m

(10- 1/4)

19mm (3/4) DIA. HOLES FOR ANCHOR BOLTS

DRAIN CHASE

203m m

(8)

1-1/4 O.D

TAILPIECE

1-1/4 O.D.

WASTE

SUPPLIES AS REQ'D

178m m

(7)

864m m

(34)

REF.

597m m (23- 1/2)

400m m (15- 3/4)

PEDE STAL

SIDE SECT ION

178m m

(7)

546m m

(21- 1/2)

REMINISCENCE™ PEDESTAL SINK

• Vintage-styled basin with raised motif backsplash and design-coordinated pedestal

• Made from vitreous china

• Rear overow

• Supplied with mounting kit

• Design matched to Reminiscence toilet

• Faucet ledge Shown with 3801.452 Amarilis Jasmine faucet and handles (not included)

❏ 0211.800 Faucet holes on 8" (203mm) centers

(Illustrated)

❏ 0211.400 Faucet holes on 4" (102mm) centers ❏ 0211.100 Center hole only

Nominal Dimensions: 660 x 508 x 864mm (26" x 20" x 34")

REMINISCENCE™

PEDESTAL SINK

VITREOUS CHINA

Separate Components:

❏ 0211.008 Pedestal top-8" (203mm) centers ❏ 0211.004 Pedestal top-4" (102mm) centers ❏ 0211.001 Pedestal top-center hole only ❏ 734900-400 Pedestal only

Bowl sizes:

476mm (18-3/4") wide 292mm (11-1/2") front to back 133mm (5-1/4") deep

Compliance Certications Meets or Exceeds the Following Specications:

• ASME A112.19.2M for Vitreous China Fixtures

To Be Specied:

❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Silver ❏ Fawn Beige ❏ Black

❏ Faucet*: ❏ Faucet Finish: ❏ Supplies: ❏ 1-1/4" Trap:

* See faucet section for additional models available

NOTES:

DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TR AP ARE

SUGGESTED.

▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED.

■ SUITABLE FOR REINFORCEMENT ONLY. ACTUAL DIMENSIONS MUST

BE TAKEN FROM FIXTURE. FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS. INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.

IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to c hange or cancellation. No responsibility is assumed for use of superseded or voided pages.

Revised 2/08