American Standard 3354 User Manual

INSTALLATION INSTRUCTIONS

AFWALL FLUSH VALVE
WALL-MOUNTED TOILETS

Model 3351, 3352, 3353, 3354

Meets the American Disabilities Act Guidelines and ANSI A117.1
Requirements for the Physically Challenged

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure thisproduct
is installed properly, please read these instructions carefully before you begin. (Certain installations may require
professional help.) Also be sure your installation conforms to local codes.

!

CAUTION: PRODUCT IS FRAGILE. TWO PEOPLE ARE RECOMMENDED FOR
HANDLING TO AVOID BREAKAGE AND POSSIBLE INJURY!

NOTE: For proper operation product requires a minimum of 30 psi working line pressure

RECOMMENDED TOOLS AND MATERIALS

Closet Carrier Support
Putty Knife

Pictures may not exactly define contour of china

1

FINISHED WALL

660mm

(26)

73mm
(2-7/8)

C/L OF SEAT POST
HOLES 140 mm
(5-1/2) CENTER

330mm

(13)

32mm
(1-1/4)

FOR WALLS UP TO 1" IN THICKNESS FOR EACH INCH
ADDITIONAL THICKNESS OF WALL ADD 25mm (1) TO
MEASUREMENT SHOWN

FINISHED WALL

95mm
(3-3/4)

38mm (1-1/2) DIA. HOLE IN WALL

76mm(3) DIA. HOLE IN WALL
FOR 1-1/2 SPUD

32mm
(1-1/4)

(3-1/4)

62mm

(2-1/8)

142mm

19mm

(3/4)

83mm

(5-1/4)

(3/4)

19mm
83mm

(3-1/4)

62mm

(2-1/8)

(5-1/4)

133mm

470mm

(18-1/2)

FINISHED

660mm

C/L OF SEAT POST HOLES
140mm(5-1/2) CENTERS

330mm

Regular Screwdriver
Adjustable Wrench

AS REQUIRED TO FLUSH VALVE

1-1/2 SPUD

381mm

(15)

or

432mm

(17)

FLOOR

(26)

470mm
(18-1/2)

(13)

FINISHED

FLOOR

1" N.P.T. OR C.W.T. SUPPLY

C/L

121mm

(4-3/4)

356mm

(14)

(4) 22mm

HOLES

229mm

(9)

C/L OF
OUTLET

1" C.W.T. OR N.P.T. SUPPLY
AS REQ'D NOT FURNISHED

121mm

(4-3/4)

254mm

41mm
(1-5/8)

89mm
(3-1/2)

(4) 22mm (7/8)

DIA. HOLES

381mm

(15)

or

432mm

(17)

C/L OF
OUTLET

292mm

(11-1/2)

(7/8)

191mm

(7-1/2)

133mm

(5-1/4)

(10)

38mm

C/L

(1-1/2)

VACUUM BREAKER

356mm

(14)

229mm

(9)

or

Refer to instructions supplied with wall carrier for proper installation of 4-bolt support
system wall cavity requirements and rough-in information for waste outlet piping.

Sealant
Tape Measure

When installed,
top of seat is
17" to 19"
(432mm to 483mm)
from the finished
floor.

184mm

(7-1/4)

298mm
(11-3/4)

191mm

(7-1/2)

133mm

184mm

or

(5-1/4)

(7-1/4)

Carpenters Level
Flush Valve

2

FIXTURE MOUNTING

Fixture studs should project
1-7/8" (48mm) from face of
finished wall.

Side View

Front View

FINISHED
WALL

1-7/8"
(48mm)

(4) STUDS

SAVE FOR FUTURE USE

Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2007

Saniwares

7301115-100 Rev. B

3

Place back-up nuts on both bottom bolts, and
the top left-hand bolt only.

Adjust the two lower back-up nuts so that front
face of nuts is flush with finished wall.

4

Using a level, adjust the top left back-up nut so that
it is in the same vertical plane as the lower left back-up
nut. (If wall surface is irregular, the three back-up
nuts must be positioned to allow a minimum 1/16"
gap between fixture and wall surface.)

Adjust waste horn to project 5/16" (7mm) from
finished wall.

FINISHED WALL

CLOSET
CARRIER
SYSTEM

5

FINISHED WALL

(3) NUTS

WASTE
HORN

5/16" (7mm)

NOTE: Bearing nuts and washers must be set
to take full loading from the fixture allowing
1/16" (2mm) clearance between fixture and wall.

Follow support manufacturer's recommended
setting of closet outlet connection.

Place felt or neoprene gasket (wax ring not
recommended) on closet outlet.

When the fixture is installed, closet outlet
gasket must be compressed sufficiently to
assure a gas and watertight seal.

1/16" (2mm)
(IRREGULAR
WALL SURFACE)

LEVEL

AMERICAN-STANDARD ONE-YEAR LIMITED WARRANTY

If inspection of this American-Standard plumbing product, within one year after its
initial installation, confirms that it is defective in materials or workmanship,
American-Standard will repair or, at its option, exchange the product for a similar
model.

This warranty does not apply to local building code compliance. Since local
building codes vary considerably, the purchaser of this product should check with a
local building or plumbing contractor to insure local code compliance before
installation.

This warranty shall be void if the product has been moved from its initial place of
installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or
other damage; if it was not installed in accordance with American-Standard's
instructions; or if it has been modified in a manner inconsistent with the product as
shipped by American-Standard.

American-Standard's option to repair or exchange the product under this warranty
does not cover any labor or other costs of removal or installation, nor shall

American-Standard be responsible for any other incidental or consequential
damages attributable to a product defect or to the repair or exchange of a
defective product, all of which are expressly excluded from this warranty. (Some

states or provinces do not allow the exclusion or limitation of implied warranties, so this
exclusion may not apply to you.)

The following steps require a helper:

Install bowl on support using cap nuts and fiber
washers with the back-up nuts and washers.

DO NOT APPLY TOP RIGHT FIBER WASHER
AND CAP NUT UNTIL OTHER CAP NUTS
HAVE BEEN FIRMLY TIGHTENED USING A
WRENCH.

Install top right cap nut with fiber washer and
run up hand tight. Wrench tighten approximately
1/4 turn.

Apply sealant to gap between bowl and finished
wall. Remove excess sealant.

7301115-100 Rev. B

This warranty gives you specific legal rights. You may have other statutory rights
that vary from state to state or from province to province, in which case this warranty
does not affect such statutory rights.

For service under this warranty, it is suggested that a claim be made through the
contractor or dealer from or through whom the product was purchased, or that a
service request (including a description of the product model and of the defect) be
sent to the following address:

In the United States:

American Standard Inc.

P.O. Box 6820

Piscataway, New Jersey 08855

Attention: Director of Consumer Affairs

For residents of the United States,

warranty information may also be

obtained by calling the following
toll free number: [phone]

www.americanstandard-us.com

Customer Service Manager
Ideal Standard, S.A. de C.V.

Via Morelos #330

Col. Santa Clara

Ecatepec 55540 Edo. Mexico

www.americanstandard.com.mx

In Mexico:

In Canada:

American-Standard

2480 Stanfield Road

Mississauga, Ontario

Canada L4Y 1S2

Toll Free: [phone]

www.americanstandard.ca

- 2 -