American Standard 3351.160, 3353.160, 3352.160, 3354.160 User Manual
AFWALL™ ELONGATED TOILET
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE
BUILDING FACILITIES - CHECK LOCAL CODES.
When installed so top of seat is 432 to 483mm (17" to 19") from the
finished floor.
BARRIER FREE
• Wall-mounted ushometer valve toilet
• Vitreous china
• Low-consumption (6.0 Lpf/1.6 gpf)
• EverClean® surface inhibits the growth of
stain- and odor-causing bacteria, mold,
and mildew on the surface
• Condensation channel
• Elongated bowl
• Powerful direct-fed siphon jet action
• 1-1/2" inlet spud
• Fully-glazed 2-1/8" trapway
• 10" x 12" water surface area
• 100% factory ush tested
❏ 3351.160 Elongated bowl only, top spud
❏ 3352.160 Elongated bowl only, top spud with
slotted rim for bedpan holding (White only)
❏ 3353.160 Elongated bowl only, back spud
❏ 3354.160 Elongated bowl only, back spud with
slotted rim for bedpan holding (White only)
Component Parts:
❏ 047007-0070A Inlet Spud (furnished with bowl)
AFWALL™ ELONGATED
1.6 GPF FLUSHOMETER TOILET
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
Nominal Dimensions:
660 x 356 x 381mm
(26" x 14" x 15")
Recommended working pressure–between
25 psi at valve when ushing and 80 psi static
Fixture only, less seat, bolt caps, and ush valve
Compliance Certications Meets or Exceeds the Following Specications:
• ASME A112.19.2 for Vitreous China Fixtures
• CAN/CSA International B45
To Be Specied:
❏ Color: ❏ White ❏ Bone ❏ Silver ❏ Linen ❏ Black
❏ Seat:
❏ American Standard #5901.100 Heavy duty open
front less cover
❏ American Standard #5905.100 Extra heavy duty
open front less cover
❏ Flushometer Valve:
❏ American Standard Selectronic™ #6065.161.002
DC Power (Top Spud)
❏ American Standard Selectronic™ #6065.262.007
DC Power (Concealed Back Spud)
❏ American Standard Selectronic™ #6067.262.007
AC Power (Concealed Back Spud)
❏ American Standard Selectronic™ #6068.262.007
Multi AC Power (Concealed Back Spud)
© 2008 AS America Inc.
M73
Revised 11/08
FINISHED WALL
470mm
(18-1/2)
C/L OF S EAT POST HOLES
140mm(5- 1/2) CENTERS
660mm
(26)
133mm
(5-1/4)
191mm
(7-1/2)
(4) 22mm (7/8)
DIA. HOLES
356mm
(14)
C/L OF
OUTLET
FINISHED
FLOOR
32mm
(1-1/4)
381mm
(15)
330mm
(13)
(3/4)
19mm
133mm
(5-1/4)
95mm
(3-3/4)
C/L
229mm
(9)
89mm
(3-1/2)
76mm(3) DIA. HOLE IN WALL
FOR 1-1/2 SPUD
70mm
(2-3/4)
283mm
(11-1/8)
330mm
(13)
FIN IS HED W ALL
470 mm
(18 -1 /2)
C/L OF SE AT PO ST
HOL ES 140 mm
(5- 1/2) C ENTER
660 mm
(26 )
73m m
(2- 7/ 8)
133mm
(5-1/4)
191mm
(7-1/2)
292mm
(11-1/2)
(4) 22mm
(7/8)
HOLES
356 mm
(14 )
C/L OF
OUTLET
121 mm
(4- 3/ 4)
FINISHED
FLOOR
32mm
(1-1/4)
381mm
(15)
1" N.P.T. OR C.W.T. SUPPLY
AS REQUIRED TO FLUSH VALVE
330mm
(13)
19mm
(3/4)
133mm
(5-1/4)
95mm
(3-3/4)
70mm
(2-3/4)
1-1/2 SPUD
C/L
229mm
(9)
3351.160/3352.160
BARRIER FREE
AFWALL™ ELONGATED
1.6 GPF FLUSHOMETER TOILET
© 2008 AS America Inc.
3353.160/3354.160
NOTES:
● Toilet designed to meet ADA accessibility standards when top of seat height set at
432 to 483mm (17" to 19") from nished oor.
PRODUCT 33 51.160 SHOWN, 3352.160 SAME AS EXCEPT WITH SLOTTED RIM FOR BED
PAN HOLDING.
PRODUCT 33 53.160 SHOWN, 33 54.160 SAME AS EXCEPT WITH SLOTTED RIM FOR BED
PAN HOLDING.
WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITE-FELT (WAX RING
NOT RECOMMENDED).
SUGGESTED 2mm (1/16) CLEARANCE BET WEEN FACE OF WALL AND BACK OF BOWL.
TO COMPLY WITH AREA CODE GOVERNING THE HEIGHT OF VACUUM BREAKER ON
THE FLUSHOMETER VALVE, THE PLUMBER MUST VERIFY DIMENSIONS SHOWN FOR
SUPPLY ROUGHING.
FLUSHOMETER VALVE NOT INCLUDED WITH FIX TURE AND MUST BE
ORDERED SEPARATELY.
CARRIER FITTING AS REQUIRED TO BE FURNISHED BY OTHERS.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORT.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range of
tolerances established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility is assumed for
use of superseded or voided pages
M74
Revised 11/08
Loading...