American Standard 2981, 2980 User Manual
Installation
Instructions
THE
“”
COLLECTION
by
™
DECK-MOUNT
BATH FILLER
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
2980
2981
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Required Tools
Flat Blade Screwdriver
*Wrench
Adjustable Wrench
Channel Locks
SPOUT ASSEMBLY
1
Turn off hot and cold water supplies before beginning.
Insert SPOUT SHANK (1) through center hole of MOUNTING LEDGE.
Make sure that the RUBBER RING (2) is properly seated in RECESS
at base of SPOUT (3).
Assemble RUBBER WASHER (4) and BRASS WASHER (5) onto
SHANK (1). From underside of ledge secure SPOUT (3) into position
with LOCKNUT (6).
*Hex key
*Supplied with Fitting
CAUTION
ROUGHING-IN DIMENSIONS
4-1/4"
MOUNTING
SURFACE
8-5/8"
2-7/8"
3/4-14 MALE
N.P.T. INLETS
2
2-1/2D.
1-1/8 D.
1-1/16 D.
PREPARE TUBE AND TEE ASSEMBLY
Prepare TUBE and TEE ASSEMBLY (1) to fit center to center
VALVE (2) location (between 6-1/2" and 12"). If necessary,
cut and/or bend TUBING carefully. Make sure tube bend is
close to the TEE (1) so that it will not effect the compression
joint at the VALVE CONNECTION.
Remove COUPLING NUT (3) and FERRULE (4) from each
VALVE (2) and slide onto TUBING (5).
3-1/2"
(H)
Certified to comply with ANSI A112.18.1M
ADJ. 6-1/2 TO 12
2-1/2D.
1-1/4
MAX.
4
3
3
(C)
12 MAX
M968212
2-1/16
D.
1-1/2 MAX.
1-3/16 D.
7-1/4
RECESS
4
6
1
5
3
3
4
1
2
MOUNTING
LEDGE.
2-1/2D.
ADJ. 6-1/2 TO 12
2-1/2D.
MOUNTING
SURFACE
5
2
NOTE
VALVE inlet is 3/4-inch NPT male.
VALVE ASSEMBLY
3
Install LOCKNUTS (1) and RUBBER WASHERS (2) onto valve shanks.
Push TUBING (3) ends into VALVE (4) side outlets. Insert VALVES (4)
into mounting holes from underside of ledge.
Press TEE (5) onto SPOUT SHANK (6) making certain that the O-RING (7) is
properly seated on SHANK (6). Push COUPLING (8) into TEE (5) and attach to
SPOUT SHANK (6) and tighten.
Thread of VALVE BODY (4) should extend at least 5/16 inch above MOUNTING
SURFACE (11). If necessary, adjust LOCKNUT (1).
Place RUBBER RING (10) into ESCUTCHEON ADAPTERS (9) and thread onto
valves until snug against internal stop.
Tighten LOCKNUT (1) to secure VALVE (4) position.
Slide FERRULE (12) and COUPLING NUT (13) to outlet of VALVE (4) and tighten
COUPLING NUT (13) firmly.
Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
9
11
2
1
MOUNTING
SURFACE
INSTALL HANDLES
4
5/16'' MIN.
10
4
9
10
HOT
MOUNTING
SURFACE
4
12
13
3
5
8
11
13
9
10
7
6
12
4
COLD
6
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
ADAPTER (1) without spline is facing up. See figure "A".
Thread HANDLE BASE (3) onto DECK ADAPTER (7)
Push HANDLE (4) onto ADAPTER (1).
Find correct position of HANDLE (4) by adjusting male teeth on
ADAPTER (1) to female teeth in HANDLE (4).
Secure HANDLE (4) with HANDLE SCREW (5).
Push INDEX CAP (6) in hole of HANDLE (4).
SERVICE
5
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Pull out INDEX CAP (1) and remove
HANDLE SCREW (2).
Pull off HANDLE (3), and unscrew
ESCUTCHEON (4).
Pull off STEM ADAPTER (7).
Remove SPRING CLIP (6).
Lift STOP WASHER (5), turn 90° and replace.
Replace SPRING CLIP (6) and STEM ADAPTER (7).
Reinstall ESCUTCHEON (4) and HANDLE
ASSEMBLY (1,2 & 3).
If spout drips, operate handles several times
from OFF to ON position. Do not force - handles
turn only 90°.
Figure "A"
SPLINE END DOWN
5
4
TOP
3
1
2
7
1
2
3
4
90°
6
7
5
M968212
Loading...