American Standard 2908EC User Manual
REMINISCENCE ELITE™
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
REMINISCENCE ELITE™ WHIRLPOOL
Comfortable oval bathing design with raised
headrest and molded in armrests
2908E (specify White 020, Bone 021, or
Linen 222)
• Acrylic with fiberglass reinforcement
• 1.5 HP self-draining pump/motor
with dry run seal
• Eight multi-directional and flow adjustable jets
including:
Two high performance Ideal-flow™ Jets
Six interchangeable Flex-jets™
• Two silent air volume controls
• Deck-mounted On/Off control
• Complete factory installed and tested
whirlpool system
2908EC (specify White 020, Bone 021, or
Linen 222)
• Same as above with the StayClean™
whirlpool system featuring Antimicrobial
AlphaSan®
Nominal Dimensions: 66” x 36” x 24-1/4"
(1676 x 914 x 616mm)
© 2006 American Standard Inc.
HD-021
SPS 2908E
Revised 04/06
Compliance Certifications Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
* See American Standard Faucet Selector
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
Components Needed:
Bath Filler*: (specify finish)
Bath Drain: BATH-DRAIN
(specify Chrome 002, Polished Brass 099,
or Satin 295)
Custom Accessories Available:
Pulse Jet Kit: PULSE-JET (two per kit,
specify White 020, Bone 021, or Linen 222)
Soft Jet Kit: SOFT-JET (two per kit, specify
White 020, Bone 021, or Linen 222)
E-Z-Install™ Whirlpool Heater - EZHEAT-100
NOTE: E-Z-Install™ Whirlpool Heater is designed to
maintain water temperature during operation. It will not
heat cold water to desired bathing temperature.
REMINISCENCE ELITE™
WHIRLPOOLS BY AMERICAN STANDARD
HIGH GLOSS ACRYLIC
© 2006 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA
TYPE INSTALLATION. SUPPORT OF BATH BY SUMP BEDDING. SUPPORT AND ENCLOSING MATERIAL
BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL
INFORMATION.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI
Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided leaflet.
HD-022
GENERAL SPECIFICATIONS FOR 2908E WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
MIN. OPERATING GAL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
66 x 36 x 24-1/4 In. (1676 x 914 x 616mm)
95 Lbs. (43 Kg.)
659 Lbs. (299 Kg.)
68 Gal. (257 L.)
55 Gal. (208 L.)
40 x 18 In. (1016 x 457mm)
53 x 28 In. (1346 x 711mm)
15 In. (381mm)
40 Lbs./Sq. Ft. (191 Kgs/Sq. m.)
23.8
44.5
WHIRLPOOL ELECTRICAL SPECIFICATIONS
1.6 HP, 9.7 AMPS, 120V.PUMP
Loading...