American Standard 2908.002, 2908.028W, 2908.018WC, 2908.018W User Manual
REMINISCENCE™ DROP-IN
WHIRLPOOL & BATHING POOL
HIGH GLOSS ACRYLIC
REMINISCENCE DROP-IN WHIRLPOOL &
BATHING POOL
❏
2908.018W Whirlpool featuring System I
• Acrylic with fiberglass reinforcement
• Pre-leveled tub bottom
• Sculptured rim design w/raised headrest
• Dual, molded-in arm rests
• Faucet deck/accessory area at drain end
• 1.5 HP single speed, self-draining pump/motor
• Factory installed power cord with plug
• Eight multi-directional and flow-adjustable jets
including:
- Two Ideal-flow jets at foot area
- Four body massage jets
- Two recessed back-rest jets
• Deck-mounted, air switch On/Off
• Two silent air volume controls
• Quick Connect Safe-T-Heater connection
system
• Factory installed and tested whirlpool system
❏
2908.018WC StayClean™ Whirlpool
Massage featuring System I
• Same as 2908.018W except with the
StayClean™ whirlpool system featuring
Antimicrobial AlphaSan®
❏
2908.028W Whirlpool featuring System II
Same as 2908.018W except:
• 2.0 HP, two speed, self-draining pump/motor
with pulse feature
• Deck-mounted electronic control with 20
minute built-in timed safety shut off and
Chrome bezel
❏
2908.028WC StayClean™ Whirlpool
Massage featuring System II
• Same as 2908.028W except with the
StayClean™ whirlpool system featuring
Antimicrobial AlphaSan®
❏
2908.002 Bathing Pool only
Nominal Dimensions: 66” x 36” x 24-1/4"
(1676 x 914 x 616mm)
© 2005 American Standard Inc.
BV-5
To Be Specified - Required:
❏ Color:
❏ Bath Faucet (Specify finish)
❏ Bath Drain: 1583.470 (Specify finish)
To Be Specified - Optional:
❏ Safe-T-Heater*: 9075.120
❏ Jet Trim Ring Kit: 9860.200-two per kit (Specify finish)
for Body Massage Jets only
❏ System II Control Bezel: 9861.100 (Specify finish)
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
Rev. 10/05
Compliance Certifications Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
For color/finish availability and other faucet choices, please see
the Product Selector and Pricing Guide.
* NOTE: the Safe-T-Heater is designed to maintain water
temperature during operation. It will not heat cold water to desired
bathing temperature.
REMINISCENCE™ DROP-IN
WHIRLPOOL & BATHING POOL
HIGH GLOSS ACRYLIC
© 2005 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA
TYPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL
SUPPORT REQUIRED.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL
INFORMATION.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI
Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided leaflet.
■
330mm
457mm
914mm
(36)
INTEGRAL
FITTING DECK
152mm
C/L OF OVERFLOW
149mm REF.
INTEGRAL
SUPPORT
FEET
(13)
(18)
(6)
(5-7/8)
79mm
(3-1/8)
ROUGH
FLOOR
1-1/2 N.P.T.M. THREADS
C/L OF
DRAIN
OUTLET
RIM AT
DRAIN END
1-1/2 O.D.TAILPIECE
ON/OFF
SWITCH
229 x 305mm
(9 X 12)
FLOOR
CUTOUT
64mm REF.
(2-1/2)
1676mm
(66)
OUTLINE OF
CUTOUT
SAFE-T-HEATER
REMOVABLE BLANK
LEVELING STRINGER
(NOT FOR SUPPORT)
PROVIDE ACCESS
TO PUMP FOR SERVICE
ON ALL INSTALLATIONS
70mm
(2-3/4)
464mm
(18-1/4)
117mm
(4-5/8)
73mm
(2-7/8)
616mm
(24-1/4)
PUMP
330mm
457mm
914mm
(36)
INTEGRAL
FITTING DECK
152mm
C/L OF OVERFLOW
149mm REF.
INTEGRAL
SUPPORT
(13)
(18)
(6)
(5-7/8)
79mm
(3-1/8)
FEET
ROUGH
FLOOR
1-1/2 N.P.T.M. THREADS
C/L OF
DRAIN
OUTLET
RIM AT
DRAIN END
1-1/2 O.D.TAILPIECE
229 x 305mm
(9 X 12)
FLOOR
CUTOUT
64mm REF.
(2-1/2)
1676mm
(66)
OUTLINE OF
CUTOUT
LEVELING STRINGER
(NOT FOR SUPPORT)
70mm
(2-3/4)
464mm
(18-1/4)
117mm
(4-5/8)
73mm
(2-7/8)
616mm
(24-1/4)
GENERAL SPECIFICATIONS FOR 2908 WHIRLPOOL
INSTALLED SIZE
66 x 36 x 24-1/4 In. (1676 x 914 x 616mm)
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
MIN. OPERATING GAL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
40 x 18 In. (1016 x 457mm)
53 x 28 In. (1330 x 718mm)
WATER DEPTH TO OVERFLOW
FLOOR LOADING
40 Lbs./Sq. Ft. (191 Kgs/Sq. m.)
(PROJECTED AREA)
PTS.
CUBE (FT3)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM I PUMP
SYSTEM II PUMP
95 Lbs. (43 Kg.)
659 Lbs. (299 Kg.)
68 Gal. (257 L.)
55 Gal. (208 L.)
15 In. (381mm)
23.8
44.5
1.6 HP, 9.7 AMPS, 120V.
2.1 HP, 15.6 AMPS, 120V.
GENERAL SPECIFICATIONS FOR 2908 BATHING POOL
INSTALLED SIZE
66 x 36 x 24-1/4 In.
(1676mm x 914 mm x 616mm)
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
40 x 18 In. (1016 x 457mm)
53 x 28 In. (1330 x 718mm)
39 Lbs./Sq. Ft. (187 Kgs/Sq. m.)
95 Lbs. (43 Kg.)
659 Lbs. (299 Kg.)
68 Gal. (257 L.)
15 In. (381mm)
(PROJECTED AREA)
PTS.
CUBE (FT3)
23.8
44.5
Loading...